POSJET PK105 Series User manual

Posjet Thermal printer
PK105 Series
Operation manual
MEGADATA INDUSTRIAL, Inc.
No. 16, Ln. 11, Nanhe 1st St., South Dist., Taichung
City 402, Taiwan (R.O.C.)
TEL: [phone] FAX:[phone]
www.posjet.com.tw [email protected]

Content
1. Specification P.3
2. The functions of control panel (Optional) P.4
3. Communication P.5
4. Commandsets P.6
5. Command code description and example P.10
6. Mechanical Dimensions P.24

1. Specification
Printing
Method Direct thermal
Effective area 48 mm
Resolution 8 dots / mm
Speed 50 mm / second (Max.)
Fonts
Character Set
A
SCII International, (Traditional/Simplify Chinese)
Characters ASCII 48 (16*8), 32 (16*12) 32(24*12) (H x W dot)
Character Chinese 24(16*16), 16(24*24)(Chinese) (H x W dot)
Graphic Bit addressable graphic command set
Bar codes Code 39, EAN and UPC
Downloadable Fonts, graphics, logos and additional bar codes
Interface
Bluetooth Class II 10~15M(outdoor)
Paper roll “Easy paper loading design”
Width 57.5 mm (2”)
Thickness 2.2 to 3.5 mils
Diameter 40 mm (Max.) Core: 12 mm
Length 16 meter (Max.)
Power supply
Li – Polymer rechargeable battery 7.2V/2200mA
Dimensions
Size 90 (W) x 150(L) x 60mm (H)
Weight 800g with Battery/Paper (Paper roll 40mm)
Environmental
Operating Temp 0 to 50°C
Storage Temp -20 to 60°C
Humidity 20~85% RH (non-condensing)

2. The functions of control Jump(connector)
PK-105
On/OffLine Feed
2.1 The function of button:
Line Feed Key: Line Feed –
Press once One line feed
Hold it Feeding continuously and stop when release
On/Off Key: Power on/off
Power off status hold it and power on Self-test page will printing out
Press it more than 2 seconds Power off
2.2 The function of LED and Buzzer:
Green LED: Power and status indicator
Red LED: Alarm and status indicator
Status Green LED
Stand-by On
No paper Blinking

3. Communication
Bluetooth connection
a. Need to match the Bluetooth connection between PK105 and your facility
before using at the first time.
b. The PIN CODE is four number “0000 “ (PK105 Bluetooth module)
c. Printing controls same as RS-232.
*The printer has one communication interface RS-232. The RS-232 has hardware
handshaking. Programmer can easily setup connection. Set primary device communication as
9600,n, 8,1 then transfer to printer. When printer received 0ah or 0dh it will start printing.
Programmer hint (for RS-232 communication)
a. In special condition you can send printer inquiry command to confirm printer status.
As usually; we do not check it.
b. In RS-232 communication must send 0ah, 0dh to enable start printing.
c. ESC (1Bh), 0Ah, 0Dh etc. unprintable characters treat as 1 data byte.

4. Command sets
Command Control code Description
LF 0Ah Line Feed
CR 0Dh Carriage return.
ESC+SP+n 1Bh+20h+n, 0<n<255
Sets the character spacing
ESC+’－’+n 1Bh+2Dh+n, 0<n<1 Enable/Disable under line mode
ESC+’＿’+n 1Bh+5Fh+n, 0<n<1 Enable/Disable upper line mode.
ESC+’ ‘ ‘+n+data 1Bh+27h+n+data Print curving graph lines
ESC+’[‘+n+0+data 1Bh+5Bh+n+00h+data
Print the bit image mode
ESC+’＊’+m+n1+n2+data 1Bh+2Ah+m+n1+n2+data Print the bit image mode
ESC+’(‘+’B’+n+n1+barcode
data 1Bh+28h+42h+n+n1 1 < n < 5 Barcode printing mode.
(See Table 4)
ESC+’{‘+n 1Bh+7Bh+n, 0<n<1
Enable/Disable upside-down printing
mode
ESC+’@’ 1Bh+40h Initialize printer
ESC+’1’+n 1Bh+31h+n, 0<n<255 Set line spacing rate of minimum
pitch
ESC+’3’+n 1Bh+33h+n, 0<n<255
Set line spacing (Use in graphic
mode)
ESC+’H’+n 1Bh+48h+n, 0<n<6 Select/Cancel n times height
ESC+’K’+n1+n2+data 1Bh+4Bh+n1+n2+data Print the bit image mode
ESC+’M’+n 1Bh+4Dh+n, 0<n<2
Select Ascii character font
(see Table 1) only use in standard
mode
ESC+’R’+n 1Bh+52h+n
0 < n < 6 (Chinese version)
0 < n <10(Standard version)
Select an international character
(see Table 2)
ESC+’W’+n 1Bh+57h+n, 0<n<6 Select/Cancel n times width
ESC+’Z’+n 1Bh+5Ah+n, 0<n<6 Select/Cancel n times height and n
times width
ESC+’b’+n 1Bh+62h+n, 0 < n < 7 Communication speed setting.
(See Table 3)
ESC+’c’+’3’+n 1Bh+63h+33h+n, 0<n<1
Enable/disable paper sensor
ESC+’c’+’5’+n 1Bh+63h+35h+n, 0<n<1
Enable/disable switch
ESC+’c’+’6’+n 1Bh+63h+36h+n, 0<n<1
Enable/disable Temperature sensor
ESC+’d’+n 1Bh+64h+n, 1 < n < 255 After printing feed n lines

GS+’!’ 1Dh+21h+n, 0<n<255
Select character size
GS+’＊’+n1+n2+n3+data 1Dh+2Ah+n1+n2+n3+data Define the download bit image
GS+’/’ 1Dh+2Fh
Printing the download bit image
GS+’B’+n 1Dh+42h+n, 0<n<1
Turn white/black reverse printing
mode on/off
GS+V+0 1Dh+56h+00h
Cut paper
GS+’k’+m+n+dn 1Dh+6Bh+m+n+dn
65 <= m <=73 Barcode printing mode
(see table 5)
GS+’h’+n 1Dh+68h+n, 0<n<=255
n=16 (default) Select the height of the barcode
(use in GS k)
GS+’w’+n 1Dh+77h+n, 0<n<=255
n=0 (default) Select the width of the barcode
(use in GS k)
GS+’H’+n 1Dh+48h+n, 0=<n<=2
n=2 (default)
Selecting of Printing Position of HRI Code
(use in GS k)
FS+’&’ 1Ch+26h
Select Chinese character mode
FS+’.’ 1Ch+2Eh
Cancel Chinese character mode
Table1: Select Ascii character font
N Character Set
0 Ascii font (16 x 8)
1 Ascii font (16 x 12)
2 Ascii font (24 x 12) default
Table2: Set up international code
Chinese Big-5 version (24 x 12)
N Character Set
0 U.S.A (16 x 8)
1 U.S.A (16 x 12)
2 U.S.A (24 x 12) default
3 France (24 x 12)
4 Germany (24 x 12)
5 U.K. (24 x 12)
6 Denmark I (24 x 12)
7 Sweden (24 x 12)
Chinese Big-5 version (16 x 12)

N Character Set
0 U.S.A (16 x 8)
1 U.S.A (16 x 12)
2 U.S.A (24 x 12) default
3 France (16 x 12)
4 Germany (16 x 12)
5 U.K. (16 x 12)
6 Denmark I (16 x 12)
7 Sweden (16 x 12)
8 Italy (16 x 12)
9 Spain (16 x 12)
Chinese Big-5 version (16 x 8)
N Character Set
0 U.S.A (16 x 8)
1 U.S.A (16 x 12)
2 U.S.A (24 x 12) default
3 France (16 x 8)
4 Germany (16 x 8)
5 U.K. (16 x 8)
6 Denmark I (16 x 8)
7 Sweden (16 x 8)
8 Italy (16 x 8)
9 Spain (16 x 8)
10 Japan (16 x 8)
11 Norway (16 x 8)
12 Denmark II (16 x 8)
Standard version
N Character Set
0 U.S.A
1 France
2 Germany
3 English
4 Denmark I
5 Sweden
6 Italy
7 Spain
8 Japan
9 Norway
10 Denmark II

- Latin-1
- Latin-2
- Japan1
- Russian
- Thai
- Thrkish
Table 3: Communication speed setting (RS-232 only)
N Communication speed
0 1200 bps
1 2400 bps
2 4800 bps
3 9600 bps (Default)
4 19200 bps
5 38400 bps
6 57600 bps
Table 4: Barcode prints mode
n Bar code prints mode Bar code data length
(Barcode data)
1 EAN-8 n1=0 Len=8
2 EAN-13 n1=0 Len=13
3 UPC-A n1=0 Len=12
4 UPC-E 1< n1 <9 Len=6
5 CODE 39 n1=0 1 < Len < 15(first is length define)
Table 5: Barcode prints mode
m Bar code prints mode Number(n)
(Decimal) Data (dn) (Decimal)
65 UPC-A n=11 48 <= d <= 57
66 UPC-E n=11 48 <= d <= 57
67 EAN13 n=12 48 <= d <= 57
68 EAN8 n=7 48 <= d <= 57
69 CODE39 1 <= n <= 255 32,36,37,43,45,46,47,48
<= d <= 57;65 <= d <= 90
70 ITF 1 <= n <= 255
(even number) 48 <= d <=57
71 CODABAR 1 <= n <= 255 36,43,45,46,47,48 <= d
<= 57,58;65 <= d <=68
72 CODE93 1 <= n <= 255 0 <= d <=127
73 CODE128 1 <= n <= 255 0 <= d <=127

5. Command code description and example
LF [Print and Line Feed]
Command code
ASCII LF
Hexadecimal 0A
Decimal 10
Function After printing out skips a line
Example
1. PRINT #1,”AAAAAAAAA”;CHR$(&HA);
2. PRINT #1,”BBBBBBBBB”;CHR$(&HA);
Result
1. AAAAAAAAA
2. BBBBBBBBB
CR [Carriage return]
Command code
ASCII CR
Hexadecimal 0D
Decimal 13
Function Place the print head at start position
Example
1. PRINT #1,”AAAAAAAAA”;CHR$(&HD);
2. PRINT #1,”BBBBBBBBB”;CHR$(&HD);
Result
1. AAAAAAAAA
2. BBBBBBBBB
ESC SP n [Set the character space]
Command code
ASCII ESC SP n
Hexadecimal 1B 20 n
Decimal 27 32 n
Defined region 0 <= n <= 255
Function Sets the character spacing for the right side of the character to [n ⋅ 0.125 mm]
Example
1. PRINT #1,CHR$(&H1B);CHR$(&H20);CHR$(&H0);CHR$(&HA);
2. PRINT #1,”ABCDEFGHIJK”;CHR$(&HA);
3. PRINT #1,CHR$(&H1B);CHR$(&H20);CHR$(&H5);CHR$(&HA);
4. PRINT #1,”ABCDEFGHIJK”;CHR$(&HA);
Result
ABCDEFGHIJK