Poulan Pro 530163900 User manual

ENGLISH ESPAÑOL FRANÇAIS
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves.
AVERTISSEMENT:
Lirelemanueld’instructionsetbienrespectertouslesavertisse-
ments et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
25 HHT
For Occasional Use Only
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Copyright E2003 Electrolux Home Products, Inc. 530163900 12/1/03
R

-- 2 --
SAFETY RULES
WARNING: Failure to follow all
Safety Rules and Precautions can result in
serious injury.
DANGER: THIS POWER TOOL CAN
BEDANGEROUS! This unit can cause serious
injury including amputation or blindness to the
operator and others. The warnings and safety
instructions in this manual must be followed to
provide reasonable safety and efficiency in us-
ing this unit. The operator is responsible for fol-
lowing the warnings and instructions in this
manual and on the unit. Never allow children to
use this tool.
KNOW YOUR UNIT
SReadyourinstructionmanualcarefully until
you completely understand and can follow
all warningsandsafety rules beforeoperat-
ing the unit.
DRestrict unit to users who understand and
will follow all warnings and safety rules in
this manual and on the unit.
PLAN AHEAD
WARNING: Inspect area before start-
ing unit. Remove all debris and hard objects
such as rocks, glass, wire, etc. that can rico-
chet, be thrown, or otherwise cause injury or
damage during operation.
DAlways wear eye protection when operating,
servicing, or performing maintenance on unit.
Wearing eye protection will help to prevent
brush or debris from being thrown orricochet-
ing into eyes and face which can result in
blindness and/or serious injury. Eye protec-
tion should be marked Z87.
DWear hearing protection when using this
unit.
DSecure hair above shoulder length. Secureor
remove jewelry, loose clothing, or clothing
with loosely hanging straps, ties, tassels, etc.
They can be caught in moving parts.
DStay alert. Do not operate unit when you are
tired,ill,upset,orifyouareundertheinfluence
of alcohol, drugs, or medication.
DKeep children, bystanders, and animals
away from work area a minimum of 30 feet
(10meters)whenstartingor operatingunit.
HANDLE FUEL WITH CAUTION
DEliminate all sources of sparks or flame(in-
cluding smoking, open flames, or work that
cancausesparks)intheareaswherefuelis
mixed, poured, or stored.
DMix and pour fuel in an outdoor area; store
fuel in a cool, dry, well ventilated place;use
an approved, marked container for all fuel
purposes.
DDo not smoke while handling fuel or while
operating the unit.
DDo not fill fuel tank while engine is running.
DMake sure the unit is properly assembled
and in good operating condition.
DAvoid spilling fuel or oil. Wipe up fuel spills
before starting the engine.
DMove atleast 10 feet (3meters) awayfrom
fuel and fueling site before starting engine.
DAlways store gasoline in a container ap-
proved for flammable liquids.
OPERATE YOUR UNIT SAFELY
DANGER: RISK OF CUT; KEEP
HANDS AWAY FROM BLADE--Blade
moves momentarily after the trigger is re-
leased. Do not attempt to clear away cut ma-
terial when the blade is in motion. Make sure
the switch is in the OFF position, the spark
plug wire is disconnected, andthe blade has
stopped moving before removing jammed
materialfromthecuttingblade.Donotgrabor
hold the unit by the cutting blade.
DInspect unit before each use for worn,
loose, missing, or damaged parts. Do not
use until unit is in proper working order.
DKeep outside surfaces free from oil and fuel.
DNever start or run engine inside a closed
room or building. Breathing exhaust fumes
can kill.
DAvoiddangerousenvironments.Donotuse
in unventilated areas or where explosive
vapors or carbon monoxide build up could
be present.
DDo notoverreachor usefromunstablesur-
faces such as ladders, trees,steep slopes,
rooftops,etc.Keepfirmfootingandbalance
at all times.
DDo not raise unit above your shoulders;the
cutting blade can come dangerously close
to your body.
DAlways keepunit infrontofyour body.Keep
all partsof yourbody away from thecutting
blade.
DKeep the cutting blade and air vents free
from debris.
DUse only for jobs explained in this manual.
MAINTAIN YOUR UNIT PROPERLY
DHave all maintenance other than the rec-
ommendedproceduresdescribedin thein-
struction manual performed by an autho-
rized service dealer.
DDisconnect spark plug before performing
maintenance except for carburetor adjust-
ments.
DDo not use a cutting blade that is bent,
warped, cracked, broken, or damaged in
any other way. Have worn or damaged
parts replaced by an authorized service
dealer.
DUseonlyrecommendedPoulanPRO!cut-
ting blades and replacement parts; use of
anyotherpartsmayvoidyourwarrantyand
cause damage to your unit.
DEmpty fuel tank before storing the unit. Use
upfuel leftin carburetor bystarting engineand
letting it run until it stops.
DHandcarrytheunitwiththeenginestopped
andthemufflerandcuttingbladeawayfrom
your body, preferably with the blade cover
installed.

-- 3 --
Allow blades to stop
before removing
them from the cut.
WARNING:
Blades can throw objects violently.
DYou can be blinded or injured.
DWear safety glasses.
WARNING:
Hazard zone for thrown objects
DBlades can throw objects violently.
DOthers can be blinded or injured.
DKeep people and animals 30 feet
(10 meters) away.
Boots
Blades move
momentarily
after the
trigger is
released.
WARNING:
Blades move momentarily after the
trigger is released.
DThe blades can seriously cut you or
others.
DAllow blades to stop before
removing them from the cut.
30 ft.
(10 m)
Safety
Glasses
DAllow engine to cool, empty the fuel tank,
and secure the unit before storing or trans-
porting it in a vehicle.
DDo notstorethe unitor fuel ina closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters,electric
motors or switches, furnaces, etc.
DStore unit so the cutting blade cannotacci-
dentally cause injury.
DStore unit with the blade cover installed.
DStore in a dry area out of reach of children.
SAFETYNOTICE:Exposure to vibrations
through prolonged use of gasoline powered
handtools could causebloodvessel ornerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swelling. Prolonged use in cold
weatherhasbeenlinkedtobloodvesseldam-
agein otherwisehealthypeople.Ifsymptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti vibration system
does not guarantee the avoidance of these
problems.Users who operatepower tools on
a continual and regular basis must monitor
closely theirphysical condition andthe condi-
tion of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperaturelimiting muffler and spark
arresting screen which meets the require-
mentsofCaliforniaCodes4442and4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equippedwithasparkarrestingscreen. Ifyou
operateinalocalewheresuchregulationsex-
ist, youarelegallyresponsibleformaintaining
theoperatingconditionoftheseparts. Failure
to do so is a violation of the law. For normal
homeowneruse,themufflerandsparkarrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by an autho-
rized service dealer.
ASSEMBLY
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue onmuffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
ASSEMBLY
Yourhedgetrimmer is fully assembled; noas-
sembly is required.

-- 4 --
OPERATION
KNOW YOUR HEDGE TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Comparetheillustrations withyourunit tofamiliarize yourself with thelocationof thevari-
ous controls and adjustments. Save this manual for future reference.
Hand
Guard
Muffler
Spark Plug
Throttle Trigger
ON/OFF
Switch
Throttle Lock
Throttle
Lock--out
Primer
Bulb Choke Lever
Fuel Mix
Fill Cap
Blade
Cover
ON/OFF SWITCH
The ON/OFF SWITCH is used to stop the en-
gine. To stop the engine, move the switch to the
OFF position.
CHOKE
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving choke lever to the desired position. See
STARTING YOUR ENGINE for complete start-
ing information.
PRIMER BULB
ThePRIMERBULBremovesairfromthecar-
buretor and fuel lines and fills them with fuel.
This allows you tostart the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original position.
THROTTLE TRIGGER
The THROTTLE TRIGGER controls engine
speed. Squeeze the trigger for full speedopera-
tion; release it for idle speed.
WARNING: Muffler is very hotduring
and after use. Do not touch the muffler or al-
lowcombustiblematerialsuchasdrygrassor
fuel to do so.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you donot understandthe safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling. HELPFUL TIP
Toobtainthecorrectoil mix
ratio, pour 3.2 ounces of
2--cycle synthetic oil into
one gallon of fresh gas.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycleair-
cooled engine oil designedto be mixed at aratio
of 40:1. Poulan/Weed Eater brand synthetic oil
is recommended. A 40:1 ratio is obtained by
mixing 3.2 ounces (95 ml) of oil with 1 gallon (4
liters) of unleaded gasoline). DO NOT USE au-
tomotiveoil orboatoil.Theseoilswill causeen-
gine damage. When mixing fuel, follow instruc-
tions printed on oil container. Once oil is added
to gasoline, shake container momentarily to as-
sure that the fuel is thoroughly mixed. Always
read and follow the safety rules listed under
HANDLE FUEL WITH CAUTION.
IMPORTANT
Experience indicates that alcohol blended fuels
(called gasohol or using ethanol or methanol)
can attract moisture which leads to separation
and formation of acids during storage. Acidic
gas can damage the fuel system of an engine
while in storage. To avoid engine problems,
empty the fuel system before storage for 30
days or longer. Drain the gas tank, start the en-
gine and let it run until the fuel lines andcarbure-
tor are empty. Use fresh fuel next season.
Neveruseengineor carburetorcleanerprod-
ucts in the fuel tank or permanent damage
may occur.
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operatedforlongerthan30secondsatfull
throttle. Releasing the trigger and allowing
the engine to briefly return to idle speed (5 --
10 seconds) will be sufficient.

-- 5 --
IMPORTANT POINTS
SUse theminimum throttle speednecessary
to effectively cut hedges for optimal hedge
trimmer performance.
SNever attemptto use this hedgetrimmer to
cut hedges that have any branches with a
diameter larger than 5/8"(1.5 cm).
OPERATING POSITION
Eye
Protection
Hearing
Protection
STOPPING YOUR ENGINE
DTo stop the engine, move the ON/OFF
switch to the OFF position.
SIf engine does not stop, move choke lever
to the FULL CHOKE position.
STARTING YOUR ENGINE
DFuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
DRemove the blade cover from the blade
before starting the unit.
DHold the unit on the ground in the starting
position as shown. Support unit so the
blade is off of the ground and away from
trees, bushes, onlookers, etc.
HELPFUL TIP
If your engine still does not
start after following these
instructions, please call
1--800--554--6723.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
WARNING: The cutting blade will be
moving once the throttle lock has been set
and the engine is started. Wear your protec-
tiveequipmentandobserveall safetyinstruc-
tions.
Throttle Lock
Throttle Lock-out
Throttle
Trigger
ON/OFF
Switch
1. Move the ON/OFF switch to the ON posi-
tion.
2. Engage the throttle lock as follows:
Dpress the throttle lock--out;
Dsqueeze and hold throttle trigger;
Dpress and hold throttle lock, then
Drelease the throttle trigger
NOTE: Keepthe throttlelock engageduntil
the engine starts.
3. Slowly press the primer bulb 6 times.
4. MovethechokelevertotheFULLCHOKE
position.
Choke
Lever
Primer Bulb
5. Pull starter rope handle sharply until en-
gine sounds as if it is trying to run, but do
not pull rope more than 6 times.
6. Move the choke lever to the HALF
CHOKE position.
7. Pull starter rope sharply until the engine
runs, but no more than 6 pulls.
NOTE: If the engine doesn’t start after 6 pulls
(at the HALF CHOKE position), check to
make sure the ON/OFF switch is in the ON
position. Move the choke lever to the FULL
CHOKE position and press theprimer bulb 6
times; pull the starter rope 2 more times.
Move the choke lever to the HALF CHOKE
position and pull the starter rope until the en-
gine runs, but no more than 6 more pulls. If
the engine still doesn’t start, it is probably
flooded. Proceed to STARTING A
FLOODED ENGINE.
8. Once the engine starts, allow the engine to
run 10 seconds, then move the choke lever
totheOFFCHOKEposition.Allowtheunitto
runfor30more seconds atthe OFFCHOKE
position before squeezing and releasing the
throttle trigger to release the throttle lock.
NOTE:If engine dies with the choke lever in
the OFF CHOKE position, move the
choke lever to the HALF CHOKE position
and pull the rope until the engine runs, but
no more than 6 pulls.

-- 6 --
STARTING A WARM ENGINE
1. Move the ON/OFF switch to the ON posi-
tion.
2. Slowly press the primer bulb 6 times.
3. Move the choke lever to the HALF
CHOKE position.
4. Engage the throttle lock as directed in
STARTING A COLD ENGINE.
NOTE: Keepthe throttlelock engageduntil
the engine starts.
5. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
6. Allow the engine to run 10 seconds, then
move the choke lever to the OFF CHOKE
position.
7. Releasethethrottlelockbysqueezingand
releasing the trigger.
NOTE:If engine has not started, pull starter
rope 5 more pulls. If engine still does not
run, it is probably flooded. Proceed to
STARTING A FLOODED ENGINE.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
theON/OFFswitchintheONpositionandthe
choke lever in the OFF CHOKE position and
engaging the throttle lock as directed in the
STARTING A COLD ENGINE section; then,
pull the rope to clear the engine of excess
fuel. Starting could require pulling the starter
rope many times depending on how badly the
unit is flooded. If the unit still doesn’t start, refer
to the TROUBLESHOOTING TABLE or call
1-800-554-6723.
SERVICE
WARNING: Ensure ON/OFF switch
is in the OFF position and disconnect the
spark plug before performing maintenance
except for carburetor adjustments.
HELPFUL TIP
IMPORTANT: Have all
repairs other than the rec-
ommended maintenance
described in the instruction
manual performed by an
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, Electrolux Home Products,
Inc., may not pay for repairs underwar-
ranty. Itisyourresponsibilitytomaintain
and perform general maintenance.
GENERALRECOMMENDATIONS
Thewarrantyonthisunitdoesnotcoveritems
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
CHECK FOR LOOSE
FASTENERS AND PARTS
SSpark Plug Boot
SAir Filter
SHousing Screws
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
SON/OFF Switch -- Ensure ON/OFF switch
functions properly by moving the switch tothe
OFF position. Make sure engine stops; then
restart engine and continue.
SFuel Tank -- Do not useunit if fuel tank shows
signs of damage or leaks.
SGearbox -- Do notuse ifthe gearboxshows
signs of damageor leaks. After50 hoursof
use, we recommend that your gearbox be
serviced by an authorized service dealer.
INSPECT AND CLEAN UNIT AND
LABELS
SBefore and after each use, inspect com-
plete unitfor loose ordamagedparts. After
each use, clean the unit and labels using a
damp cloth with a mild detergent.
SWipe off unit with a clean dry cloth.
CLEAN AIR FILTER
Air Filter
Cover
Screw
Air Filter
Cleaning the air filter:
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
1. Clean the cover and the area around it to
keepdebrisfromfallingintothecarburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
NOTE: Donotcleanfilteringasolineorother
flammable solvent. Doing so can create a fire
hazardor produceharmfulevaporativeemis-
sions.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Adda fewdropsof oil tothe filter;squeeze
filter to distribute oil.
6. Replace parts.
INSPECT MUFFLER AND SPARK
ARRESTINGSCREEN
WARNING: The muffler on this prod-
uct contains chemicals known to the State of
California to cause cancer.

-- 7 --
As your unit is used, carbondeposits build up
on the muffler and spark arresting screen.
For normal homeowner use, however, the
mufflerandsparkarrestingscreenwill notre-
quire any service. After 50 hours of use, we
recommend that your muffler be serviced or
replaced by your authorized service dealer.
CARBURETOR ADJUSTMENT
WARNING: Keep others away when
making idle speed adjustments. The blade
will be moving during most of this procedure.
Wearyour protectiveequipmentandobserve
all safety precautions. When making adjust-
ments, use a screwdriver short enough to
keep your hands behind the handguard and
away from the blade. After making adjust-
ments,theblademustnotmoveatidlespeed.
The carburetor has been carefully set at the
factory.Adjustments maybenecessaryifyou
notice any of the following conditions:
SEngine will not idle when the throttle is re-
leased.
SThe blade moves at idle.
Keep others away when making idle speed
adjustments. Make adjustments with the unit
resting on a level surface free of debris that can
be caught in the hedge trimmer blade. Serious
injury to the operator and others can occur if the
carburetor is not properly adjusted. Keep all
parts of your body away from the blade and
muffler.
Idle Speed Adjustment
Allowenginetoidle. Adjustspeeduntilengine
runswithoutblademoving(idletoofast)oren-
gine stalling (idle speed too slow).
STurn idle speed screw clockwise to in-
creaseenginespeedif enginestalls ordies.
STurnidle speedscrew counterclockwise to
decrease enginespeed if the blademoves
at idle.
WARNING: Recheck the idle speed
after each adjustment. The blade must not
move at idle speed to avoid serious injury to
the operator or others.Idle Speed Screw
Ifyourequirefurtherassistanceorareunsure
about performing this procedure, contact an
authorized service dealer or call
1--800--554--6723.
BLADE ADJUSTMENT
The clearance between the cutting blades
mustbeadjustedperiodicallytomaintainopti-
mal performance and sharp cutting.
Blade
guide
Bolt
Blades
Cupped
Washer
Flat
Washer
Blade guide
Nuts
Nut
1. Using a wrench, loosen each nut on the
top side of the blade guide.
Wrench
Nut TOP SIDE OF BLADE
2. Tighten each bolt from underside of blade
with a wrench.
UNDERSIDE OF BLADE
Bolt
3. Loosen each bolt 1/2 turn.
UNDERSIDE OF BLADE
Bolt
1/2 turn
4. While holding each bolt in place with a
wrench, retighten the nuts.
TOP SIDE
OF BLADE

-- 8 --
NOTE: After adjustment, the washers be-
tween the bolt head and the blade should be
able to be turned by hand, but not loose
enough to move when the unit is tilted from
side to side.
CAUTION: If the clearance between the
cutting blades is set too wide, the blades will
notcutcorrectly.Ifthebladesareadjustedtoo
tight, overheating may occur.
REPLACE SPARK PLUG
Replace spark plug each year to ensure the
engine starts easier and runs better. Set
spark plug gap at 0.025 inch (0.6 mm). Igni-
tion timing is fixed, nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and dis-
card.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
(19 mm) socket wrench.
4. Reinstall the spark plug boot.
REPLACE FUEL FILTER
Toreplacefuelfilter,drainunitbyrunningitdry
of fuel, then remove fuel cap/retainer assem-
bly from tank. Pull filter from tank andremove
itfromthefuelline.Installnewfuelfilteronfuel
line; reinstall parts.
Fuel Line
Fuel
Filter
STORAGE
WARNING: Perform the following
steps after each use:
SAllow engine to cool, and secure the unit
before storing or transporting.
SStore unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
SStore unit with the blade cover installed.
Position unit so that any sharp object can-
not accidentally cause injury.
SStore unit and fuel well out of the reach of
children.
SEASONALSTORAGE
Prepareunit for storageat end ofseason or if
it will not be used for 30 days or more.
If your unit is to bestoredfor aperiodof time:
SClean the entire unit.
SStore in a clean dry area.
SClean all parts and check for damage.
Have damaged parts repaired or replaced
by an authorized service dealer.
SKeep all nuts, bolts, and screws tight.
SLightly oil external metal surfaces, includ-
ing the blade.
SInstall the blade cover.
To oil the blade, do the following:
SStopthe engineandallow bladeto cometo
a complete stop.
SEnsure ON/OFF switch is in the OFF posi-
tion.
SDisconnect the spark plug wire.
SApply a light machine oil along the edgeof
the top strap as shown.
Top Strap
OIL
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TIONsectionofthismanual,seemessagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine. Fuel stabilizer is an ac-
ceptable alternative in minimizing the formation
of fuel gum deposits during storage. Add stabi-
lizer to gasoline in fuel tank or fuel storage con-
tainer. Follow the mix instructions found on sta-
bilizer container. Run engine at least 5 minutes
after adding stabilizer.
HELPFUL TIP
Duringstorageofyourgas/
oil mixture,theoil will sepa-
rate from the gas.
We recommend that you
shake the gas can weekly
toinsureproperblendingof
the gas and oil.

-- 9 --
ENGINE
SRemove spark plugand pour1 teaspoonof
40:1,2-cycle engineoil (air cooled)through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
SReplacesparkplugwithnewone ofrecom-
mended type and heat range (see RE-
PLACE SPARK PLUG section).
SClean air filter.
SCheck entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
SAt the beginning of the next season, use
only freshfuelhavingthepropergasolineto
oil ratio.
OTHER
SDo not store gasoline from one season to
another.
SReplaceyourgasolinecanifitstartstorust.
NEED ASSISTANCE?
NEED ASSISTANCE?
Call 1-800-554-6723for assistance.
NEED SERVICE PARTS?
Contact your dealer.
TROUBLE CAUSE REMEDY
Engine will not
start.
Engine will
not idle
properly.
1. Carburetorrequires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Air filter dirty.
2. Spark plug fouled.
3. Carburetorrequires
adjustment.
4. Carbonbuild-up on
muffler outlet screen.
5. Compression low.
Engine will not
accelerate,
lacks power,
or dies under
a load.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
smokes
excessively.
1. Choke partially on.
2. Fuel mixture incorrect.
3. Air filter dirty.
4. Carburetorrequires
adjustment.
1. Adjust choke.
2. Empty fuel tank and refill with
correct fuel mixture.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
Engine runs
hot. 1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetorrequires
adjustment.
4. Carbon build-up on
muffler outlet screen.
1. See “Fueling Engine” in Operation
section.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
WARNING: Alwaysstop unitand disconnectsparkplugbeforeperformingall ofthe
recommendedremedies below except remedies that require operation of the unit.
TROUBLESHOOTINGTABLE
1. ON/OFF switch in the
OFF position.
2. Engine flooded.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
6. Compression low.
1. Move ON/OFF switch to the ON
position.
2. See “Starting a Flooded Engine”
in Operation Section.
3. Fill tank with correct fuel mixture.
4. Install new spark plug.
5. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
6. Contact an authorized service dealer.

-- 10 --
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
warrants to theoriginal purchaser that each new
Poulan PROrbrand gasoline tool or attach-
ment is free from defects in material and work-
manship and agrees to repair or replace under
this warranty any defective gasoline product or
attachment as follows from the original date of
purchase.
2 YEARS -- Parts and Labor, when used for
household purposes.
60 DAYS -- Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS -- Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
accessories and/or attachments notspecifically
recommended by ELECTROLUX HOME
PRODUCTS, INC., for this tool. Additionally,
this warranty does not cover tune--ups, spark
plugs, filters, starter ropes, starter springs, cut-
ting line, or rotating head parts that will wear and
require replacementwith reasonable use during
the warranty period. This warranty does not
cover predelivery setup or normal adjustments
explained in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CON-
SEQUENTIALDAMAGES, SO THEABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of ELECTROLUX HOME PRO-
DUCTS, INC., is to continuously improve its
products. Therefore, ELECTROLUX HOME
PRODUCTS, INC., reserves the right to
change, modify, or discontinue models, de-
signs, specifications, and accessories of all
products at any time without notice or obligation
to any purchaser.
U.S. EPA / CALIFORNIA / ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U.S. Environmental
Protection Agency/California Air Resources
Board,EnvironmentCanadaandELECTRO-
LUX HOME PRODUCTS, INC., are pleased
to explain the emissions control system war-
ranty on your year 2002--2004small off--road
engine. In California, all small off--road en-
gines must be designed, built, and equipped
to meet the State’s stringent anti--smog stan-
dards. ELECTROLUX HOME PRODUCTS,
INC., must warrantthe emission control sys-
temonyoursmalloff--roadenginefortheperi-
ods of time listed below provided there has
been no abuse, neglect, or improper mainte-
nance of your small off--road engine. Your
emission control system includes parts such
as the carburetor and the ignition system.
Where a warrantableconditionexists, ELEC-
TROLUX HOME PRODUCTS, INC., will re-
pair your small off--road engine engine at no
costtoyou.Expensescoveredunderwarran-
ty include diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COV-
ERAGE:Ifanyemissions relatedpartonyour
engine (as listed under Emissions Control
WarrantyPartsList) isdefectiveora defectin
the materials or workmanship of the engine
causesthefailureofsuchanemissionrelated
part, the part will be repaired or replaced by
ELECTROLUX HOME PRODUCTS, INC.
OWNER’S WARRANTY RESPONSIBILI-
TIES: As the small off--road engine engine
owner, you are responsible for the perfor-
mance of the required maintenance listed in
your instruction manual. ELECTROLUX
HOMEPRODUCTS,INC.,recommendsthat
you retain all receipts covering maintenance
on your small off--road engine, but ELEC-
TROLUX HOME PRODUCTS, INC., cannot
denywarrantysolely forthelackof receiptsor
for your failure to ensurethe performance of
allscheduledmaintenance. Asthesmalloff--
road engine engine owner, you should be
aware that ELECTROLUX HOME PROD-
UCTS, INC., may deny you warranty cover-
age if your small off--road engine engine or a
part of it has failed due to abuse, neglect, im-
proper maintenance, unapproved modifica-
tions, or the use of parts not made or ap-
provedby theoriginalequipmentmanufactur-
er. You are responsible for presenting your
small off--road engine to an ELECTROLUX
HOME PRODUCTS,INC., authorizedrepair
centeras soonas a problem exists. Warranty
repairs should be completed in a reasonable
amountof time, not to exceed 30days. If you
have any questions regarding your warranty
rightsandresponsibilities,youshouldcontact
your nearestauthorizedservice centerorcall
ELECTROLUXHOMEPRODUCTS,INC.,at
1--800--554--6723. WARRANTY COM-
MENCEMENT DATE: The warranty period
begins on the date the small off--road engine
is purchased. LENGTH OF COVERAGE:
This warranty shall be for a period of two
yearsfromtheinitialdateofpurchase. WHAT
IS COVERED: REPAIR OR REPLACE-
MENT OF PARTS. Repair or replacement of
any warranted part will be performed at no
charge to the owner at an approved ELEC-
TROLUX HOME PRODUCTS, INC., servic-

-- 11 --
ing center. If you have any questions regard-
ing your warranty rights and responsibilities,
you should contact your nearest authorized
service center or call ELECTROLUX HOME
PRODUCTS, INC., at 1--800--554--6723
WARRANTY PERIOD: Any warranted part
whichisnotscheduledforreplacementasre-
quired maintenance, or which is scheduled
only for regular inspection to the effect of “re-
pair or replace as necessary” shall be war-
ranted for 2 years. Any warranted part which
is scheduled for replacement as required
maintenanceshallbewarrantedfortheperiod
of time up to the first scheduled replacement
point for that part. DIAGNOSIS: The owner
shall not be charged for diagnostic labor
which leads to the determination that a war-
ranted part is defective if the diagnostic work
is performed at an approved ELECTROLUX
HOME PRODUCTS, INC., servicing center.
CONSEQUENTIAL DAMAGES: ELEC-
TROLUXHOME PRODUCTS,INC., may be
liable for damages to other engine compo-
nents caused by the failure of a warranted
partstill underwarranty.WHATIS NOTCOV-
ERED: All failures caused by abuse,neglect,
or improper maintenance are not covered.
ADD--ON OR MODIFIED PARTS: The use
of add--on or modified parts can be grounds
for disallowing a warranty claim. ELECTRO-
LUX HOME PRODUCTS, INC., is not liable
tocoverfailuresofwarrantedpartscausedby
theuseofadd--onormodifiedparts.HOWTO
FILEA CLAIM:Ifyouhaveany questionsre-
gardingyour warrantyrights andresponsibili-
ties, you should contact your nearest autho-
rized service center or call ELECTROLUX
HOME PRODUCTS, INC., at
1--800--554--6723. WHERE TO GET WAR-
RANTY SERVICE: Warranty services or re-
pairs shall be provided at all ELECTROLUX
HOME PRODUCTS, INC., service centers.
Call: 1--800--554--6723 MAINTENANCE,
REPLACEMENT AND REPAIR OF EMIS-
SION RELATED PARTS: Any ELECTRO-
LUXHOMEPRODUCTS,INC.,approvedre-
placement part used in the performance of
any warrantymaintenanceor repair on emis-
sion related parts will be provided without
charge to the owner if the part is under war-
ranty. EMISSION CONTROL WARRANTY
PARTS LIST: Carburetor, Ignition System:
Spark Plug (covered up to maintenance
schedule), Ignition Module, Muffler including
catalyst. MAINTENANCE STATEMENT:
Theowneris responsiblefortheperformance
of all required maintenance as defined in the
instruction manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)