Power Electronics SD 300 Series User manual

SD300
ACCESSORIES MANUAL
ETHERNET MODULE
www.power-electronics.com

A C C E S O R I E S
Ethernet Module
Accessories Manual
Edition: August 2017
SD30MA01AI

SD300 - ETHERNET MODULE
POWER ELECTRONICS
2

POWER ELECTRONICS
SD300 - ETHERNET MODULE
3
ABOUT
PURPOSE
This manual contains important instructions for the installation and
maintenance of the optional Ethernet communication module for Power
Electronics SD300 variable speed drives.
AUDIENCE
This manual is intended for qualified customers who will install, operate and
maintain Power Electronics SD300 variable speed drives.
Only trained electricians approved by the installation company may install
and commission the drives. The instructions assume that the installer is
familiar with electrical installation rules and regulations.
REFERENCE MANUALS
The following reference guide is available for the SD300 variable speed
drives:
•Getting Started Manual
POWER ELECTRONICS CONTACT INFORMATION
Power Electronics, S.A.
C/ Leonardo da Vinci, 24 –26
46980 –PATERNA
SPAIN
Tel. [phone] (Spain) • Tel. [phone] • Fax [phone]
Email: [e-mail]
Website: www.power-electronics.com

SD300 - ETHERNET MODULE
POWER ELECTRONICS
4
Revisions
The equipment and technical documentation are periodically updated. Power
Electronics reserves the right to modify all or part of the contents of this manual without
previous notice. To consult the most updated information of this product, you may
access through our website www.power-electronics.es, where the latest version of this
manual can be downloaded.
Date Revision Description
29 / 08 / 2017 A First edition.

POWER ELECTRONICS
SD300 - ETHERNET MODULE
TABLE OF CONTENTS
5
TABLE OF CONTENTS
1. INTRODUCTION ......................................................... 14
What is Ethernet?......................................................... 14
Components ................................................................. 14
2. ETHERNET COMMUNICATION MODULE
FEATURES....................................................................... 15
Common Features........................................................ 15
Layout of the module.................................................... 16
3. INSTALLATION AND CONNECTION......................... 17
Installation .................................................................... 17
Terminal Block of Ethernet Communication……………….
Specification ................................................................. 22
Network cable specification ..................................... 23
Protocol Selection.................................................... 24
LEDs description...................................................... 25
4. MODBUS TCP............................................................. 28
Modbus TCP frame structure........................................ 28
Function Codes............................................................. 29
Exception Frame........................................................... 29
5. ETHERNET IP............................................................. 31
Basic Protocol Configuration ........................................ 31
Implicit Messaging........................................................ 32
Supported range...................................................... 33
Input instance........................................................... 34
Output instance........................................................ 37
Explicit Messaging........................................................ 40
Identity object (Class 0x01, Instance 1)................... 40

SD300 - ETHERNET MODULE
POWER ELECTRONICS
6
TABLE OF CONTENTS
Motor data object (Class 0x28, Instance 1).............. 42
Control supervisor object (Class 0x29, Instance 1).. 43
AC Drive Object (Class 0x2A; Instance 1) ............... 46
Class 0x64 (Drive Object) –Manufacture Profile..... 48
6. PARAMETERS CONFIGURATION............................. 49
7. LOST COMMAND....................................................... 56
Drive Keypad Parameters............................................. 56
Modbus/TCP Lost Command Status........................ 57
Ethernet/IP Lost Command Status........................... 57
8. CONFIGURATION REGISTER ................................... 58

POWER ELECTRONICS
SD300 - ETHERNET MODULE
SAFETY SYMBOLS
7
SAFETY SYMBOLS
Always follow safety instructions to prevent accidents and potential hazards
from occurring.
In this manual, safety messages are classified as follows:
The following CAUTION symbols can be used in this manual and they
symbolize:
WARNING
Identifies potentially hazardous situations where
dangerous voltage may be present, which if not avoided,
could result in minor personal injury, serious injury or
death.
Be extremely careful and follow the instructions to avoid
the risk of electrical shocks.
CAUTION
Identifies potentially hazardous situations, which if not
avoided, could result in product damage, or minor or
moderate personal injury.
Read the message and follow the instructions carefully.
NOTICE
Identifies important measures to take in order to prevent
damage equipment and warranty lost, as well as
encouraging good use and environmental practices
Hot surface. Be careful and follow the instructions to
avoid burns and personal injuries.
Risk of fire. Be careful and follow the instructions to
prevent causing an unintentional fire.

SD300 - ETHERNET MODULE
POWER ELECTRONICS
8
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
IMPORTANT!
Read carefully this manual to maximize the performance of the product and
to ensure its safe use.
In order to appropriately use the drive, please, follow all instructions
described in the installation manual which refer to transportation, installation,
electrical connection and commissioning of the equipment.
Power Electronics accepts no responsibility or liability for partial or total
damages resulting from incorrect use of equipment.
Please, pay careful attention to the following recommendations:
WARNING
Be cautious when handling the CMOS components of the
communication module.
Static may lead to product malfunctioning.
Turn the drive power off before changing the communication cable.
Otherwise, you may damage the module or a communication error may
occur.
Make sure to insert precisely the communication module connector to
the drive.
Otherwise, you may damage the module or a communication error may occur.
Check the parameter unit before setting up the parameters.
Otherwise, a communication error may occur.
Do not remove the cover while power supply is connected or the drive
is operating.
Otherwise, you may get an electric shock.
Do not run the drive with the front cover removed.
Otherwise, you may get an electric shock.