Power House 500Wi User manual

500Wi OM
500Wi Digital Inverter Generator
By POWERHOUSE®
OWNER’S MANUAL
PLEASE READ THIS MANUAL
CAREFULLY BEFORE USING

2 500Wi OM
Quick Start Guide
Use outdoors only. Generators produce carbon monoxide —
a poisonous, colorless, odorless gas that can cause death or
serious injury.
Always operate on a level surface
Keep away from rain, snow or other wet conditions
Keep away from smoking materials, sparks, and other sources
of combustion when refueling.
Pre-Operation:
1. Add oil by removing the maintenance panel and inspecting the dipstick. Fill the oil reservoir
with 7.4 oz. (220 ml) of oil or to the full mark on the dipstick. Use appropriate grade,
high-detergent, premium quality, 4-stroke engine oil. Use SAE 15W-40 viscosity oil unless
operating at ambient temperatures below 32° F (0° C). For temperatures below 32° F, use
SAE 0W-40 viscosity oil. See page 14 for more information about operating at extreme
temperatures.
2. Carefully add regular unleaded automotive gasoline up to the shoulder of the filler neck. To
avoid spilling fuel, use care to not fill too quickly or over fill. Avoid getting dirt, dust, or water in
the fuel tank. Do not use a blend that contains more than 10% ethanol. Do not use gasoline
containing methanol. An octane rating of 87 or higher is recommended.
Operation:
1. Ensure that no loads have been connected to the AC receptacle.
2. Open the fuel valve.
3. Push the engine switch on the control panel to the ―ON‖ position.
4. Move the choke lever to the ―START‖ position.
5. Pull the starter grip lightly until resistance is felt, then pull briskly out. Repeat until the engine
starts.
6. Move the choke lever to the ―RUN‖ position after the engine warms up.
7. The green ―RUN‖ light will illuminate when the generator is ready for use.
8. Make sure that all appliances to be connected have been switched off and are in good working order.
Confirm that the electrical rating does not exceed that of the generator.
9. Connect the appliance to the appropriate receptacle on the generator’s panel.
10. To minimize fuel consumption and noise, push the economy switch to the ―ON‖ position. This setting
regulates the engine’s speed so that it matches the needs of the connected loads. Do not use
the economy setting if you are connecting items with electric motors that have a high amperage
draw during startup or with appliances that cycle on and off rapidly.
In an emergency, pushing the Engine Switch on the control panel
to the “OFF” position will automatically stop the engine with or
without a load. However, repeatedly stopping the generator
without disconnecting all loads can cause damage to the
generator or appliances.
Shutdown:
1. Turn off all connected appliances and disconnect from the generator.
2. Push the engine switch on the control panel to the ―OFF‖ position.
3. Turn the fuel valve to the OFF‖ position.

3 500Wi OM
PREFACE
Thank you for purchasing a POWERHOUSE generator.
This manual covers operation and maintenance of POWERHOUSE generator model 500Wi.
All information in this publication is based on the latest product information available at the time of
approval for printing.
We reserve the right to make changes at any time without notice and without incurring any obligation.
No part of this publication may be reproduced without written permission.
This manual should be considered a permanent part of the generator and should remain with it if it is
resold.
Pay special attention to statements preceded by the following words:
Indicates a strong possibility of severe personal injury or death if instructions are not
followed.
Indicates a possibility of personal injury or equipment damage if instructions are not
followed.
Gives helpful information.
If you have a problem with this generator, do not return it to the store where you purchased it.
For warranty support call 877-544-4449 from 8am to 6pm ET, email us at
[e-mail] or send a fax to 800-263-0280.
Failure to properly follow these precautions can result in property
damage, serious injury, or DEATH!
Read all labels and the Owner's Manual before operating this
generator.
Generators produce carbon monoxide —a poisonous, colorless,
odorless gas that can cause death or serious injury.
Indoor use of a generator can kill quickly. Generators should be
used outdoors only.
Generators should only be used outdoors away from garages and
open windows, but protected from rain and snow.
Check for spilled fuel or leaks. Clean and/or repair before use.
Always stop engine before refueling. Wait 5 minutes before
restarting.
Keep any source of ignition away from fuel tank, at all times.
The portable generator is not meant to be used as a permanent
back-up power system for the home. A permanently installed
stationary generator is designed to be safely used for this specific
purpose.
Our generators are designed to give safe and dependable service if operated
according to instructions. Read and understand the Owner's Manual before
operating the generator. Failure to do so could result in personal injury or equipment
damage.
©Copyright DTS Manufacturing /The Coast Distribution System, Inc. 2011

4 500Wi OM
CONTENTS
1. SAFETY INSTRUCTIONS.............................................................................................................5
2. COMPONENT IDENTIFICATION..................................................................................................7
2.1 Control panel 500Wi ................................................................................................................8
2.2 Serial number and bar code identification and location ..........................................................9
3. PRE-OPERATION CHECK..........................................................................................................10
3.1 Check the engine oil level......................................................................................................10
3.2 Check the fuel level................................................................................................................11
3.3 Check the air cleaner.............................................................................................................12
4. OPERATING INSTRUCTIONS....................................................................................................13
4.1 Starting the engine.................................................................................................................13
4.2 High altitude operation...........................................................................................................14
4.3 Operating at extreme temperatures.......................................................................................14
4.4 Generator use........................................................................................................................15
4.5 AC application........................................................................................................................17
4.6 Output and Overload Lights...................................................................................................18
4.7 DC application........................................................................................................................19
4.8 Low oil alarm system .............................................................................................................20
4.9 Economy switch.....................................................................................................................21
4.10 Stopping the engine.............................................................................................................21
5. MAINTENANCE...........................................................................................................................22
5.1 Emission control system........................................................................................................22
5.2 Maintenance Schedule ..........................................................................................................24
5.3 Changing oil...........................................................................................................................25
5.4 Air cleaner service..................................................................................................................26
5.5 Spark plug maintenance ........................................................................................................27
5.6 Spark arrestor maintenance...................................................................................................29
6. TRANSPORTING and STORAGE...............................................................................................30
6.1 Transporting the generator.....................................................................................................30
6.2 Short term storage of the generator.......................................................................................30
6.3 Storing the generator for an extended period:.......................................................................31
6.4 Exercising the Generator.......................................................................................................31
7. TROUBLESHOOTING.................................................................................................................32
7.1 Engine will not start:...............................................................................................................32
7.2 Appliance does not operate: ..................................................................................................33
7.3 No output at the DC receptacle: ............................................................................................33
8. SPECIFICATIONS.......................................................................................................................34
9. WARRANTYAND CONSUMER INFORMATION........................................................................35
9.1 CALIFORNIA EMISSIONS CONTROLWARRANTY STATEMENT......................................36
9.2 EMISSION CONTROL SYSTEM WARRANTY.....................................................................37
10. APENDIX B - EMISSION CONTROL SYSTEM ........................................................................37
11. APENDIX C - SAFETYAND CHARGING INSTRUCTIONS.....................................................38

5 500Wi OM
1. SAFETY INSTRUCTIONS
■This generator is designed to give safe and dependable service if operated
according to instructions.
Read and understand the Owner's Manual before operating the generator.
Failure to do so could result in personal injury or equipment damage.
■Exhaust gas contains poisonous carbon monoxide. Never run the generator in
an enclosed area.
Be sure to provide adequate ventilation.
■The muffler becomes very hot during operation and remains hot for several
minutes after stopping the engine.
Be careful not to touch the muffler while it is hot.
Let the engine cool before storing the generator indoors.
To ensure safe operation
Gasoline is extremely flammable and explosive under certain conditions. Refuel
in a well ventilated area with the engine stopped.
Keep away from cigarettes and sparks when refueling the generator.
Wipe up spilled gasoline at once.

6 500Wi OM
■This generator is not intended, nor designed, for use as a standby power supply
and should never be used as such. Severe property damage and/or severe
personal injury or death may result. Never connect this generator to an
automatic transfer switch (ATS). Severe damage to the generator will occur.
■To avoid accidents or equipment damage, always make a pre-operation
inspection before you start the engine.
■Place the generator at least 3 ft (1 m) away from buildings or other equipment
during operation.
■Operate the generator on a level surface. If the generator is tilted, fuel spillage
may result.
■Know how to stop the generator quickly and understand operation of all controls.
Never permit anyone to operate the generator without proper instructions.
■Keep children and pets away from the generator when it is in operation.
■Keep away from moving parts while the generator is running.
■Generators are a potential source of electrical shocks when misused; do not
operate with wet hands.
■Do not operate the generator in rain or snow and do not let it get wet.
■Do not operate this generator inside a compartment. Doing so may lead to
overheating and, consequently, fire. It may also lead to death by asphyxiation.
■Do not modify the enclosure of this generator.

7 500Wi OM
2. COMPONENT IDENTIFICATION
Spark Plug
Access Door
Fuel Cap
Control
Panel
Choke Lever
Starter Grip
Fuel Lever
Maintenance
Door
Exhaust
Grill

8 500Wi OM
2.1 Control panel 500Wi
Run Light
Overload
Light
Low Oil
Alarm
Light
120V ~ 20A
Receptacle
120V ~ 5A
Circuit Breaker
Engine Switch
Economy
Switch
Grounding
Terminal
Battery Charge
Receptacle
12V ~ 2.5A
Battery Charge
Circuit Breaker

9 500Wi OM
2.2 Serial number and bar code identification and location
The generator bar code number and the engine serial number identify your particular unit and are necessary
when ordering parts and accessories. These two numbers are used by your dealer and The Coast
Distribution System, Inc. for warranty administration and must be supplied before any work can be done.
The engine serial number can be found stamped on the
engine to the left of the oil dipstick. It is visible when the
maintenance door is removed.
The bar code label is found in two locations:
1. On the bottom of the generator.
2. On the packing carton.
Please record this information below and keep this manual in a safe place along with the bill of sale.
Engine Serial Number __________________________________
Bar Code Number _______________________________
Date of Purchase ________________________________
Name of Selling Dealership ________________________________
Please go to www.powerhouse-products.com/register and register your unit today. Online registration
will be accepted as proof of purchase. Online registration will make sure you are protected in the event you
have lost your receipt, and will significantly speed the process in the event warranty service is necessary.
For warranty assistance:
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
Serial Number
Serial Number

10 500Wi OM
3. PRE-OPERATION CHECK
■Be sure to check the generator on a level surface with the engine stopped.
3.1 Check the engine oil level.
Do not use non-detergent oil or 2-stroke engine oil. It will void the warranty
and will shorten the engine's service life.
Use a high-detergent, premium quality, 4-stroke engine oil, certified to meet
or exceed U.S. automobile manufacturer's requirements forAPI Service
Classification SG/SF.
Change the oil in a new engine between the first 4 to 6 hours of operation to
clean manufacturing debris and contamination.
Use SAE 15W-40 viscosity oil unless operating at ambient temperatures
below 32° F (0° C). For temperatures below 32°F, use SAE 0W-40 viscosity
oil. See page 14 for more information about operating at extreme
temperatures.
1. Loosen the maintenance door screws and remove the maintenance door.
2. Remove the dipstick, wipe it with a clean rag and reinsert it into the filler neck, screwing it down
completely.
3. Remove the dipstick again and check the oil level.
4. If the oil level is at or below the lower level of the dipstick, refill with the recommended oil up to the
top of the upper level marking. It may be necessary to tilt the engine slightly to allow trapped air to
escape as you add oil. Do not overfill.
5. Reinsert the dipstick and be sure to screw it down until it is tight.
■Running the engine with insufficient oil can cause serious engine damage.
■The Low Oil Alarm System will automatically stop the engine before the oil level
falls below a safe limit. However, to avoid the inconvenience of an unexpected
shutdown, it is still advisable to visually inspect the oil level regularly.
Engine oil capacity: 7.4 fl oz (0.46 pt) / 220 ml
Oil Fill Hole
Dip Stick
Upper Level
Lowest oil
level allowed

11 500Wi OM
3.2 Check the fuel level.
Use automotive unleaded regular gasoline only.
1. If the fuel level is low, refill to the bottom of the filler neck.
2. Never use an oil/gasoline mixture or dirty gasoline.
3. Avoid getting dirt, dust or water in the fuel tank.
4. After refueling, tighten the fuel filler cap securely..
■Gasoline is extremely flammable and is explosive under certain conditions.
■Refuel in a well-ventilated area with the engine stopped. Keep all smoking
materials, sparks, and any other source of combustion away from the generator
during refueling.
■Do not overfill the fuel tank (fill to the bottom of the filler neck).After refueling, make
sure the tank cap is closed properly and securely.
■Be careful not to spill fuel when refueling. Spilled fuel or fuel vapor may ignite, If
any fuel is spilled, make sure the area is dry before starting the engine.
■Avoid repeated or prolonged contact with skin or breathing of vapor. KEEP OUT
OF REACH OF CHILDREN.
Fuel tank capacity: 0.37 gal (1.4 liters)
Gasoline containing alternate fuels
Do not use a blend that contains more than 10% ethanol. Do not use gasoline containing methanol. An
octane rating of 87 or higher is recommended.
■Fuel system damage or engine performance problems resulting from the use of
fuels that contain an improper alcohol blend are not covered under warranty.
■Before buying fuel from an unfamiliar station, Determine if the fuel contains ethanol
and if it does, confirm the type and percentage of ethanol used. If you notice any
undesirable operating symptoms while using a gasoline that contains ethanol, or
one that you think contains ethanol, replace it with a gasoline that you know has the
proper blend.
Fuel Level
Fuel Cap

12 500Wi OM
3.3 Check the air cleaner
1. Loosen the maintenance door screws and remove the maintenance door.
2. Remove the air filter retaining screw. Remove the cover and check the element. Clean or replace the
element if necessary.
3. Replace the air cleaner element, and cover. Tighten the screw securely.
4. Replace the maintenance door and tighten the screws securely.
■Never run the engine without the air cleaner element in place. Rapid engine wear
will result from contaminants, such as dust and dirt, being drawn through the
carburetor, into the engine.
Air Cleaner
Case
Air Cleaner
Element
Air Cleaner
Cover
Air Cleaner
Screw
Maintenance
Cover
Cover
Screw

13 500Wi OM
4. OPERATING INSTRUCTIONS
4.1 Starting the engine
Before starting the engine, disconnect any loads from the AC and DC receptacles.
1. Turn the fuel valve lever to the ―ON‖ position.
2. Push the engine switch to the ―ON‖ position.
3. Move the choke lever to the ―START‖position.
4. Pull the starter grip lightly until resistance is felt then pull the starter grip briskly.
5. Move the choke lever to the ―RUN‖position after the engine warms up.
■Do not allow the starter grip to snap back. Return it slowly by hand.
■Do not let the starter rope rub against the generator body or the rope will
wear out prematurely.
Starter Grip
Fuel Valve
Engine Switch
Choke Lever
Start
Running

14 500Wi OM
4.2 High altitude operation
At higher altitudes, the standard carburetor air-fuel mixture will be excessively rich. Performance will
decrease, and fuel consumption will increase.
High altitude performance can be improved by installing a smaller diameter main fuel jet in the carburetor. If
you always operate the generator at altitudes higher than 5000 feet (1500 m) above sea level, have your
authorized dealer install a high altitude main jet.
Even with suitable carburetor jetting, engine horsepower will decrease approximately 3.5% for each 1000
feet (305 m) increase in altitude. The affect of altitude on the horsepower will be greater than this if no
carburetor modification is made.
Be sure to have any carburetor modification reversed before operating at lower
altitudes. Operation of the generator at an altitude lower than the carburetor is
jetted for may result in reduced performance, overheating, and serious engine
damage caused by an excessively lean air/fuel mixture.
4.3 Operating at extreme temperatures
High temperature adversely affects generator operation. Generator performance will decrease 1% for each
10°F (5.5°C) increase in temperature above 85°F (29°C). The normal operating range of this generator is 0°
to 113° F (-18° to 45°C). Although the generator can operate at 0°F (-18°C) it will be necessary to use a
lower viscosity engine oil such as SAE 0W-40. Even with 0W-40 oil, the engine will be more difficult to
start.
■Do not operate the generator when the ambient temperature is below 0°F
(-18°C).
■Do not operate the generator when the ambient temperature exceeds 113°F
(45°C).
(-18° C)
(0° C)
(45° C)

15 500Wi OM
4.4 Generator use
Be sure to ground the generator when loads are connected.
■To prevent electrical shock from faulty appliances, the generator should be
grounded. Connect a length of heavy cable between the generator's ground
terminal and an external ground source.
■Connections for standby power to a building's electrical system must be made by
a qualified electrician and must comply with all applicable laws and electrical
codes. Improper connections can allow electrical current from the generator to
back feed into the utility lines. Such back feed may electrocute utility company
workers or others who contact the lines during a power outage. When utility power
is restored the generator may explode, burn, or cause fires in the building's
electrical system.
■Do not connect the generator to an automatic transfer device. Severe damage to
the inverter module may result.

16 500Wi OM
■The total wattage of all appliances connected must be considered.
■Do not exceed the current limit specified for any one receptacle.
■Do not connect the generator to a household circuit. This could cause the
damage to the generator or to electrical appliances in the house.
■Do not modify or use the generator for other purpose than it is intended for. Also
observe the following when using the generator.
■Do not connect an extension to exhaust pipe.
■When an extension cord is required, be sure to use a rubber sheathed flexible
cord. Also make sure to use the proper size and length cord.
16 Gauge Cords- a 16 gauge cord between 0 and 100 feet long will safely handle
tool and appliance loads up to 10 amps.
14 Gauge Cords- a 14 gauge cord between 0 and 50 feet long will safely handle
tool and appliance loads between 10 and 15 amps.
12 Gauge Cords- a 12 gauge cord between 50 and 100 feet will safely handle tool
and appliance loads between 10 and 15 amps.
■Keep the generator away from other electric cables or wires such as commercial
power supply lines.
■The DC receptacle can be used while theAC power is in use. If you use both at
the same time, be sure not to exceed the total power forAC and DC.
■Most appliance motors require more than their rated wattage for start-up.

17 500Wi OM
4.5 AC application
1. Start the engine and make sure only the output (Run) indicator light (Green) comes on.
2. Confirm that the appliance to be used is switched off before plugging into the control panel.
■Substantial overloading that continuously lights the overload light (Red) may
damage the generator. Marginal overloading that temporarily lights the overload
light (red) may shorten the service life of the generator.
■Be sure that all appliances are in good working order before connecting them to
the generator. If an appliance begins to operate abnormally, becomes sluggish,
or stops suddenly, turn off the generator engine switch immediately. Disconnect
the appliance and examine it for signs of malfunction.
Run Light (Green)
120V ~ 20
Receptacle

18 500Wi OM
4.6 Output and Overload Lights
1. The output indicator light (Green) will remain illuminated during normal operating conditions.
2. If the generator is overloaded (In excess of 500 W), or if there is a short in the connected appliance,
the output indicator light (Green) will go out, the overload indicator light (Red) will turn on and current
to the connected appliance will be shut off.
3. Remove all electrical loads from the generator and investigate the cause of the overload.
4. To reset the overload condition (Red light), stop and restart the generator. The (Green) indicator light
should be illuminated within 10 seconds.
■Before connecting or reconnecting an appliance to the generator, check that it is
in good order, and that its electrical rating does not exceed that of the generator.
■When an electric motor is started, both the overload indicator light (Red) and the
output indicator light (green) may go on simultaneously. This is normal if the
overload indicator light (red) goes off after about four (4) seconds. If the overload
indicator light (Red) stays on, consult your generator dealer.
Overload
Light
120V ~ 20A
Receptacle

19 500Wi OM
4.7 DC application
The DC receptacle may be used for charging 12 volt lead acid batteries only.
Other types of batteries may burst causing personal injury or damage.
To prevent the possibility of creating a spark near the battery, connect the charging
cable first to the battery then to the generator. Disconnect the cable first at the
generator.
Before connecting charging cables to a battery that is installed in a vehicle,
disconnect the vehicle’s ground battery cable. Reconnect the vehicle's ground
battery cable after the charging cables are removed. This procedure will prevent
the possibility of a short circuit and sparks if you make accidental contact between
a battery terminal and the vehicle's frame or body.
Do not attempt to start an automobile engine with the generator still connected to
the battery. The generator may be damaged.
Connect the positive charging cord to the positive battery terminal. Do not reverse
the charging cables, or serious damage to the generator and/or battery may occur.
DC operation is only intended for the purpose of charging batteries. It should not
be used to power DC equipment.
1. For DC operation, with the engine running, turn the Economy switch to the OFF position.
2. Connect the charging cables to the battery terminals first.
3. Connect the charging cables to the DC receptacle of the generator last.
Economy
Switch

20 500Wi OM
■Batteries give off explosive gases; keep sparks, flames and cigarettes away.
Provide adequate ventilation when charging.
■Batteries contain sulfuric acid (electrolyte). Contact with skin or eyes may cause
severe burns. Wear protective clothing and a face shield.
-If electrolyte gets on your skin, flush with water.
-If electrolyte gets in your eyes, flush with water for at least 15 minutes and call a
physician immediately.
■Electrolyte is poisonous.
-If swallowed, drink large quantities of water or milk and follow with milk of
magnesia or vegetable oil and call a physician immediately.
■KEEP OUT OF REACH OF CHILDREN.
■The DC receptacle may be used while the AC power is in use.
■An overloaded DC circuit will trip the DC circuit breaker. If this happens reset the
circuit breaker to resume operation.
4.8 Low oil alarm system
The low oil alarm system is designed to prevent engine damage caused by an insufficient amount of oil in
the crankcase. Before the oil level in the crankcase falls below a safe limit, the low oil alarm system will
automatically shut down the engine (the engine switch will remain in the ON position).
If the low oil alarm system shuts down the engine, the low oil alarm indicator light (red) will come on or flicker
when you pull the starter rope and the engine will not start. If this occurs add enough of the approved engine
oil to raise the level to the top line on the dipstick.
Battery Charge Circuit Breaker
Low Oil Light (Red)