PowerLed BLE-DIM User manual

We PowerLed (wholly owned subsidiary of Sunpower
Group Holdings Ltd) of Orion House, Calleva Park,
Aldermaston, Berkshire, RG7 8SN, UK declare under
our responsibility that our product BLE-DIM is herewith
conrmed to comply with the requirements set out in the
UK legislation, Electromagnetic Compatibility Regulations
2016, and the European Council Directive on the
Approximation of the Laws of the Member States relating
to Electromagnetic Compatibility Directive (2014/30/EU).
Friday 30th October 2020.
Mark Ellis
Quality Manager
BLE-DIM
RF & Bluetooth
LED controller
Declaration
of Conformity
Registered in England: No. 9436662
Orion House, Calleva Park, Aldermaston, Berkshire, RG7 8SN www.powerled.uk.com
BLE-DIM RF & Bluetooth LED controller instructions
BLE-DIM MESH Series instructions
Product Data
• 4 in 1 universal RF+Bluetooth LED controller,
radio frequency: 2.4GHz
• 4 different device modes DIM, CCT, RGBW and RGB+CCT
in 1 controller, and selectable by dip switch
• Enables to control ON/OFF, dimming,
color temperature, RGB color of connected LED lights
• Ultra powerful to control Single Color, CCT,
RGBW, RGB+CCT LED strips
• Controlled through both smart App and remote
controls, no gateway required
• Easy & quick pairing to the smart App by scanning QR code
• Mesh network, much longer control distance, transmits
received signal to neighbor devices
• Up to 30m transmission distance between every two neighbour devices
• Encrypted two-way communication, quick status feedback, safe
& reliable data transmission
• Compatible with universal RF+Bluetooth remotes, each LED
controller can pair to max. 8 remotes
• IP Rating: IP20
12 - 24VDC Power Input LED indicator, normally stays off, flashes
when receives control signal
Common Anode Output (+)
CH1: R/R/W/W/1 OUTPUT (-)
CH2: G/G/CW/2 OUTPUT (-)
CH3: B/B/WW/3 OUTPUT (-)
CH4: WW/W/CW/4 OUTPUT (-)
CH5: CW/NC/NC/5 OUTPUT (-)
NC = No Connection
Program Key: for pairing & deleting
pairing with RF + Bluetooth remotes
Input
Voltage
12-24VDC
Output
Current
4A/CH
Output
Power
Ambient
Temperature
Max. Casing
Temperature
48-96W/CH
Remarks
Constant Voltage
Size (LxWxH)
145x46.5x16mm -20°C ~+50°C 75°C
Product Data
Safety & Warnings
Dip switch for device mode
selection, DIM, CCT, RGBW
and RGB+CCT 4 modes are available,
factory default is RGB + CCT mode
Prog.
R F +B lu et oo th L E D Co nt rol ler
Input Voltage DC 12-24V
Output Cu rrent 4A/C H
Max Power 48-96W/CH
1 2
DC INPUT
LED OUTPU T
DIM
CCT
RGBW
RGB+CCT
1- R- R-
2- G- G-
3- B- B-
4-
WW-
WW-
WW-
W-
5-
CW-
CW-
CW-
NCNC
Ta:-20℃-+50℃
1 2
ON
• DO NOT install with power applied to device.
• DO NOT operate the dial switches for device mode selection with power applied to device.
• DO NOT expose the device to moisture.

BLE-DIM RF & Bluetooth LED controller instructions
AC Power
50/60Hz
L
N
G
V+
V-
OUTPUT
INPUT
12V/24V
CV PSU
V+ V+
R- R-
G- G-
B- B-
V+ V+
WW- WW-
CW- CW-
L
N
G
V+
V-
OUTPUT
INPUT
12V/24V
CV PSU
V+ V+
R- R-
G- G-
B- B-
W- W-
Max. 20A input
Max. 20A input
Prog.
R F + B l u e to o t h L E D C o n t r o l le r
Input Voltage DC 12-24V
Output Current 4A/CH
Max Power 48-96W/CH
1 2
DC INPUT
LED OUTPUT
DIM
CCT
RGBW
RGB+CCT
1- R- R-
2- G- G-
3- B- B-
4-
WW-
WW-
WW-
W-
5-
CW-
CW-
CW-
NCNC
Ta:-20℃-+50℃
1 2
ON
Prog.
R F + B l u e to o t h L E D C o n t r o l le r
Input Voltage DC 12-24V
Output Current 4A/CH
Max Power 48-96W/CH
1 2
DC INPUT
LED OUTPUT
DIM
CCT
RGBW
RGB+CCT
1- R- R-
2- G- G-
3- B- B-
4-
WW-
WW-
WW-
W-
5-
CW-
CW-
CW-
NCNC
Ta:-20℃-+50℃
1 2
ON
1. Do wiring according to connection diagram
2. Pair LED controller with RF + Bluetooth remote: Please refer to the installation
of the remote you would like to pair with.
3. Delete the pairing:
• Wire up the LED controller diagram.
• Press and hold the ʻProgʼ button on the controller for over 3 seconds until the
connected light flashes, which means deleted.
Pair with Smart App
1. Do wiring according to connection diagram.
2. Please refer to the ʻEasy thingsʼ App user manual for details of adding the device.
Operation
Wiring Diagram
1. RGB+CCT Mode
2. RGBW Mode
Note: Please make sure the dial switches are in position for RGB+CCT mode as shown in above diagram.
Note: Please make sure the dial switches are in position for RGW mode as shown in above diagram.
RGB LED Tape
CCT LED Tape
RGBW LED Tape
AC Power
50/60Hz