powermesh PMBC2 User manual

Powermesh_Blind_Controller_Installation_Instructions.pdf 230201
Important - Read before installing.
Identifying the Blind Controllers.
Dual Blind Controller.
Single Blind Controller.
1
3
4
5
Blind 1Blind 1 Blind 2
2 Button
PMBC2
4 Button
PMBC4
2Using the Blind Controller.
Blind Switch
• Single press to
open or close
• Press to stop
LED indicator
pulses when
moving.
Status Indicator
See overleaf for the meaning
of each colour status.
Open
Close
Open
Close
Blind 1
Open
Close
Blind 2
BLIND 1BLIND 2
ACTIVE
NEUTRAL
Megger testing may lead to low readings
due to electronic components so
disconnect all electronic devices before
taking a reading. Install the included
warning sticker with circuit detail in the
main electrical switchboard.
Surge protection is recommended at
the main switchboard. Products
damaged by power surges are not
covered by warranty.
Powermesh devices must only be
connected with the Active and Neutral
from the same RCD.
Failure to follow these
instructions can result in
serious injury or death.
Must only be installed by a
LICENSED ELECTRICIAN
to local wiring regulations.
AVOID THE RISK OF ELECTRIC SHOCK
Once the product has been fastened to
the wall, ensure the screw caps are
inserted firmly into place over the screw
mounting holes.
CLOSE 1
OPEN 1
CLOSE
OPEN
CLOSE 2
OPEN 2
ACTIVE
NEUTRAL
Part Number
White PMBC4
Black PMBC4BK
Compatible Loads
Small motor
rating: M.40
Rated Loads
600W (2.5A) max per
channel, 230V~50Hz
Specifications
Specifications
Part Number
White PMBC2
Black PMBC2BK
Compatible Loads
Small motor
rating: M.40
Rated Loads
600W (2.5A) max,
230V~50Hz
Let’s get
connected.
Single and Dual
Blind Controllers.
Mounting Screws
Included on rear of device.
Factory Reset
Press until indicator flashes
blue to restore factory
settings. When the indicator
turns blue, it’s ready to pair.
(remove cover)
Snap on cover
MAC ID
Unique product
serial number.
(remove cover)
Open / Stop
Close / Stop
RESET
NEUTRAL
LINE
OPEN CLOSE
NEUTRAL LINE OPEN 1 CLOSE 1 OPEN 2 CLOSE 2
OPEN
CLOSE
Blind 1
OPEN
CLOSE
OPEN
CLOSE
Blind
2
Blind
1
Zimi Cloud Connect.
Internet connection required.
Remote access
anywhere.
Voice control
hands free.
Sunrise & Sunset
schedules.
Want to learn more or need help?
support.zimi.life
Enjoy all the features to make your life easier.
Visit our website for tips, tricks and help.
Control all your
connected blinds.
Automatically
open and close.
Schedules
Switch, app and
voice control.
Smart Blinds Double press
7
8
Pair and setup with Zimi.
6
• Download the Zimi App.
• Choose ‘Add New Device’.
• Follow the on screen instructions.
Enjoy the full experience
with all your Zimi devices.
Status Indicator.
Ready to pair.
‘Add New Device’ in Zimi to pair and complete setup.
Setup is complete.
This device has been paired and setup completed.
Action in progress.
This lets you know an automatic function is being activated.
Identify device.
This shows the device when updating its settings.
Device problem.
Please refer to support to resolve the problem.
Indicator is off.
The status indicator can be turned o and on in settings.
Blue
White
Red
Off
White
pulsing
Blue & White
pulsing
9
Download Zimi App.
Point your phone
camera at the QR code
to open the app store.
14 Millennium Circuit
Helensvale QLD 4212
Australia.
www.zimi.life
Manufacturer’s Warranty This product has been manufactured to the highest quality standards. This product is warranted
to the original purchaser and is not transferable. The product is guaranteed to be free from defects in workmanship and parts for a period
of 1 Year from the date of purchase. Defects that occur within this warranty period, under normal use and care will be repaired, replaced or
refunded. The benefits conferred by this warranty are in addition to all other rights and remedies of the consumer under a Commonwealth,
State and Territory laws in relation to the goods or services to which this warranty relates and Australian Consumer Law. Risk in regard to
the product to be repaired shall at all times remain with the Purchaser. The warranty is given on the condition that the product to which
it applies is used for the purpose and in the manner intended by its construction and for no other purposes whatsoever. Zimi Ltd shall not
be responsible for damage of any kind, caused by accidents, power surges, electrical storm damage, incorrect power current, infestation
(vermin or insect), incorrect installation, incorrect electricity or plumbing installation, improper use of controls or failure to use the unit
in accordance with the operating instructions, general misuse or abuse or from normal wear and tear. Any attempt by an unauthorised
person to repair or tamper with the equipment shall render the warranty null and void. Goods presented for repair under this warranty may
be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods. Zimi
Ltd’s liability under this warranty is limited to the replacement and/or repair of the defective parts within the warranty period and does not
extend to installation or removal of the product. Acceptance of liability by Zimi Ltd contained herein is to the exclusion of any other remedy
whatsoever and howsoever arising in respect of any equipment to which it applies.
Proof of Purchase Please keep your purchase docket or receipt as proof of purchase and as proof of the date on which the purchase
was made. The purchase docket or receipt must be presented with the warranty when making a claim under this warranty. Failure to produce
documentary proof of the date of original acquisition by the original Purchaser will result in a charge being levied for work done, labour and
parts supplied. Likewise a charge will be made for any calls following warranty claim where no fault is found with the unit.
Service during the warranty period The first point of contact for product issues is the place of purchase. The product must be
returned to the original place of purchase for product repair, replacement or refund. Please ensure the product is properly packaged so
as to ensure that no damage occurs to the product during transit and make sure that you have included an explanation of the problem.
In the event of goods requiring repair under manufacturer’s warranty the owner is responsible for the cost of transportation. Should the
goods be found to be in sound working order the owner might be charged a fee. This warranty is given by Zimi Ltd, 14 Millennium Circuit,
Helensvale, QLD 4212.
Safety Warnings Read all instructions and safety information. All electrical work must only be undertaken after disconnection of the
power by removing fuses or turning off the circuit breaker, to ensure all pole disconnection from the electrical supply. All electrical
work must be carried out by a licensed and qualified electrician and in accordance to AS/NZS 3000 Wiring Rules and applicable
local authority regulations. This product is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use
of the product by a person responsible for their safety. Young children should be supervised to ensure they do not play with the unit.
Do not cut or notch joists, beams and rafters to install the unit. Do not damage hidden electrical wiring or utilities when cutting. The
product must be installed so switches and other controls cannot be touched by a person in the bath or shower. Do not install the product
in a location where water will splash onto it. Check and confirm that all connections are proper and secure to prevent causing property
damages or injury. Do not install outdoor where it could be exposed to water or moisture (indoor use only).
Trademarks Zimi and Powermesh and their respective logos are registered trademarks of Zimi Ltd. Google and Google Play are
trademarks of Google LLC. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Apple, the Apple logo,
Apple Watch and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.,
registered in the U.S. and other countries.
Copyright © 2022 Zimi Ltd. All rights reserved.

Powermesh_Fan_Controller_Installation_Instructions_A4.pdf 230201
Let’s get
connected.
Fan Controller
with Light Switch.
Light Switch
Touch for on / off.
MAC ID
Unique product
serial number.
Reset Button
Powermesh Status Indicator
See overleaf for the meaning
of each colour status.
Fan Speed
Touch for on/off.
Slide to change speeds.
Triple tap for Speed Sense,
to sync fan speed with
temperature.
Using the Fan Controller.
Snap on cover
2
ACTIVE
NEUTRAL
FAN
LIGHT
Part Number: PMFC, PMFCBK
Line Voltage Frequency:
50Hz Nominal
Fan Load:
120 watts maximum @ 240V
Light Load:
250 watts maximum @ 240V
7 speed capacitor control:
1.1~3.3µF + full speed
Suitable for AC fans only
Specifications
Connect the wiring.
Surge protection is recommended at the main
switchboard. Products damaged by power
surges are not covered by warranty.
3
ACTIVE
NEUTRAL
NEUTRAL
Important - Read before installing.
AVOID THE RISK OF ELECTRIC SHOCK
Once the product has been fastened to the wall,
remove the screw caps and insert firmly into the
screw mounting holes.
Factory Reset
Remove the cover and press the RESET
button until the Powermesh indicator flashes blue.
Release the button and when the indicator
turns blue, it’s ready to pair.
Screw caps
Screw
mounting
holes
1
Must only be installed by a
LICENSED ELECTRICIAN to local
wiring regulations. Failure to
follow these instructions can
result in serious injury or death.
This is a semiconductor
switching device, the mains
power MUST BE SWITCHED OFF
before performing any wiring or
maintenance work.
Zimi Cloud Connect.
Requires Wi-Fi with Internet connection.
5
Remote access
anywhere.
Voice control
hands free.
Energy history
over time.
Enjoy the full experience
with all your Powermesh devices.
6Want to learn more or need help?
Enjoy all the features to make your life easier.
Visit our website for tips, tricks and help.
Sync fan speed
with temperature.
Turn it on and off
any day or time.
Schedules
Monitor the power
usage and cost.
Energy Use
Turn it off
automatically.
Auto off Timer
Speed Sense
support.zimi.life
7Powermesh Status Indicator.
Ready to pair.
‘Add device’ in Zimi to pair and complete setup.
Setup is complete.
This device has been paired and setup completed.
Action in progress.
This lets you know an automatic function is being activated.
Identify device.
This shows the device when updating its settings.
Device problem.
Please refer to support to resolve the problem.
If the device is working, the indicator has been
‘turned o’ in device settings.
Blue
White
Red
Off
White
pulsing
Blue & White
pulsing
Pair and setup with Zimi.
4
• Download the Zimi App.
• Choose ‘Add Device’.
• Follow the on screen instructions.
Zimi App Download
Point your phone
camera at the QR code
to open the app store.
Manufacturer’s Warranty This product has been manufactured to the highest quality standards. This product is warranted
to the original purchaser and is not transferable. The product is guaranteed to be free from defects in workmanship and parts for a period
of 1 Year from the date of purchase. Defects that occur within this warranty period, under normal use and care will be repaired, replaced or
refunded. The benefits conferred by this warranty are in addition to all other rights and remedies of the consumer under a Commonwealth,
State and Territory laws in relation to the goods or services to which this warranty relates and Australian Consumer Law. Risk in regard to
the product to be repaired shall at all times remain with the Purchaser. The warranty is given on the condition that the product to which it
applies is used for the purpose and in the manner intended by its construction and for no other purposes whatsoever. GSM Innovations Pty
Ltd shall not be responsible for damage of any kind, caused by accidents, power surges, electrical storm damage, incorrect power current,
infestation (vermin or insect), incorrect installation, incorrect electricity or plumbing installation, improper use of controls or failure to use the
unit in accordance with the operating instructions, general misuse or abuse or from normal wear and tear. Any attempt by an unauthorised
person to repair or tamper with the equipment shall render the warranty null and void. Goods presented for repair under this warranty may
be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods. GSM
Innovations Pty Ltd’s liability under this warranty is limited to the replacement and/or repair of the defective parts within the warranty period
and does not extend to installation or removal of the product. Acceptance of liability by GSM Innovation Pty Ltd contained herein is to the
exclusion of any other remedy whatsoever and howsoever arising in respect of any equipment to which it applies.
Proof of Purchase Please keep your purchase docket or receipt as proof of purchase and as proof of the date on which the purchase
was made. The purchase docket or receipt must be presented with the warranty when making a claim under this warranty. Failure to produce
documentary proof of the date of original acquisition by the original Purchaser will result in a charge being levied for work done, labour and
parts supplied. Likewise a charge will be made for any calls following warranty claim where no fault is found with the unit.
Service during the warranty period The first point of contact for product issues is the place of purchase. The product must be returned
to the original place of purchase for product repair, replacement or refund. Please ensure the product is properly packaged so as to ensure
that no damage occurs to the product during transit and make sure that you have included an explanation of the problem. In the event of
goods requiring repair under manufacturer’s warranty the owner is responsible for the cost of transportation. Should the goods be found
to be in sound working order the owner might be charged a fee. This warranty is given by GSM Innovations Pty Ltd, 14 Millennium Circuit,
Helensvale, QLD 4212
Safety Warnings Read all instructions and safety information. All electrical work must only be undertaken after disconnection of the
power by removing fuses or turning off the circuit breaker, to ensure all pole disconnection from the electrical supply. All electrical
work must be carried out by a licensed and qualified electrician and in accordance to AS/NZS 3000 Wiring Rules and applicable
14 Millennium Circuit
Helensvale QLD 4212
Australia.
www.zimi.life
local authority regulations. This product is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of
the product by a person responsible for their safety. Young children should be supervised to ensure that they do not play with the unit.
Do not cut or notch joists, beams and rafters to install the unit. Do not damage hidden electrical wiring or utilities when cutting. The product
must be installed so that switches and other controls cannot be touched by a person in the bath or shower. Do not install the product in a
location where water will splash onto it. Check and confirm that all connections are proper and secure to prevent causing property damages
or injury. Do not install outdoor where it could be exposed to water or moisture (indoor use only).
Trademarks Zimi and Powermesh and their respective logos are registered trademarks of GSM Innovations Pty Ltd. Google and Google
Play are trademarks of Google LLC. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Apple, the Apple
logo, Apple Watch and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple
Inc., registered in the U.S. and other countries.
Copyright © 2021 GSM Innovations Pty Ltd. All rights reserved.

Powermesh_Garage_Controller_Installation_Instructions_A4.pdf 230201
BLUE Device is operational and ready to be set
up on a network. Choose ‘Add New
Device’ in Zimi to finish setting it up.
WHITE Device has been set up on a network and
is operational. To set up on a different
network, simply RESET the device.
RED Device has a critical fault, try updating
the firmware. If unsuccessful, the unit
will have to be replaced.
OFF Please check the unit has power.
If the unit is not working, it will need to
be returned. If the unit is operational,
please check that the indicator hasn’t
been disabled in ‘device settings’.
Powermesh Indicator
Powermesh Garage Door
Controller & Sensor
Important Safety Instructions
Door Position
Light Ring
Powermesh Indicator
Temperature
& Humidity
Sensor
Reset Button
Quick
Connector
Garage Controller
Garage Controller
Quick
Connector
Wiring
Power
Plug Pack
Door Sensor
Sensor Mount
Battery
(included
with sensor)
In the Box
A garage door is the largest automated moving object in
most homes. Please ensure that all safety recommendations
and regulations are considered and adhered to.
This device allows for operation of the
garage door when the door or opener
is not in direct line of site.
As the door may operate unexpectedly you must ensure that
there is no object near the path of the door. When the door
is operating people must be kept away until the door has
come to a complete stop. Contact with a moving door may
result in serious injury, death or damage to property.
It is highly recommended that safety
beams are fitted with all installations.
• This product, or any internet device that has
the Zimi app installed, is not intended for use by
children or persons with reduced physical,
sensory or mental capabilities.
• The door sensor has an IP66 (water proof) rating
however the controller should not be installed in
a wet or damp space exposed to weather.
• Do not attempt to disassemble, repair or modify
the product in any way. This will void the
product warranty.
Installation
Instructions
Safety beams must be installed in accordance
with AS/NZ 60335-2-95:2012. Correctly installed safety
beams will prevent the door from closing if a person or
object is located within the door area.
In addition, monthly safety reverse tests and regular
professional maintenance must be carried out as detailed
in your opener’s Installation and Operating Manual.
• Unscrew the back cover.
• Remove the battery pull tab.
• Screw the back cover on.
Activate the Sensor Battery Stick the Sensor to your door
Tilt
Roller
Sectional
• Connect the wires to the ‘Bell / Push button terminals’
on your motor, refer to the motor manual if unsure.
• If using PE safety beams, wire to the P terminals.
Connect the wiring
3
1
• Plug the quick connector in to the controller.
• Peel off the adhesive backing.
• Firmly press the controller to the ceiling.
Mount the Controller
4
• Download the Zimi app and log in.
• Choose ‘Add New Device’.
• Stand near the controller and Zimi will find it.
• Follow the onscreen instructions to finish setup.
Pair with Zimi
5
to Motor Bell / Push terminals
Additional sensor is required
when using Door Motor 2.
24Vdc
250mA
V+ V- M1 M1 P1+ P1- M2 M2 P2+ P2-
Point your phone
camera at the QR code
to open the app store.
App Download
• Clean the surface for best adhesion.
• Peel off the adhesive backing.
• Stick on the sensor.
2
Stick to the spoke, on the end without the motor.
Stick to the inside bottom of the door.
Sensor
mount
Door
shaft
Stick the sensor to the mount and
push onto the door shaft.
Sensor
battery
Pull
tab
Need help?
Powermesh
Video Channel
• Put your Zimi Cloud Connect in a room near
your garage, within range of your Wi-Fi router.
• Follow the included setup instructions.
Have you got a
Zimi Cloud Connect?
6
Voice control your garage door with
your favourite voice assistant.
Voice Control Access Anywhere
Learn more about Powermesh
products or search YouTube for
Powemesh.
Visit the Zimi support site to
get help with your powermesh
products. support.zimi.life
Scan the QR
code with
your phone.

Powermesh_Light_Dimmer_Installation_Instructions_A4.pdf 230201
Important - Read before installing.
1
Must only be installed by a
LICENSED ELECTRICIAN to local
wiring regulations. Failure to
follow these instructions can
result in serious injury or death.
This is a semiconductor
switching device, the mains
power MUST BE SWITCHED OFF
before performing any wiring or
maintenance work.
AVOID THE RISK OF ELECTRIC SHOCK
Once the product has been fastened to the wall,
ensure the supplied screw caps are placed firmly
into the screw mounting holes.
Screw
mounting
holes
Factory Reset.
Remove the cover and press the RESET
button until the Powermesh indicator flashes blue.
Release the button and when the indicator turns
blue, it’s ready to pair.
2
Part Number: PMLD, PMLDBK
Line Voltage Frequency: 50Hz Nominal
Load Brightness Control Range:
1% to > 95% (load dependent)
Rated Load:
Maximum Load 1A @ 250V / 250W
Minimum Load: 2W
Dimmable LED
Drivers & Lamps
Incandescent
Dimmable CFLs
Due to the variety of LED lamps / transformers /
CFLs, the maximum load and performance will
be specific to the product make and model.
Standard iron core &
toroidal transformers
Electronic
transformers
Specifications Compatible load types
Surge protection is recommended at the main switchboard. Products
that are damaged by power surges are not covered by warranty.
Powermesh products must only be connected with the
Active and Neutral from the same RCD.
3
• Press x 1 - on /off.
• Press & hold to dim.
• Press x 2 - full brightness
• Press x 3 - timed fade to off.
Set device Min & Max
dimming levels in
Zimi ‘Settings’ to avoid
flicker if necessary.
Light Dimming Button
with mini brightness
indicator.
Mounting screws
Reset Button
Using the Light Dimmer.
Powermesh
Status Indicator
See overleaf for the
meaning of each
colour status.
Snap on cover
MAC ID
Unique product
serial number.
Let’s get
connected.
Light Dimmer.
4Choose your wiring installation.
Set the
switch
positions
as shown.
2 Wire
without Neutral
3 Wire
with Neutral
ACTIVE
NEUTRAL
NEUTRAL
ACTIVE
MASTER
SLAVE
SW1
LOAD
NEUTRAL
NO NEUTRAL
SW2
NEUTRAL
ACTIVE
MASTER
SLAVE
SW1
LOAD
NEUTRAL
NO NEUTRAL
SW2
NEUTRAL
LOAD
LOAD
ACTIVE
5Two Way Switching
Set the
switch
positions
as shown.
2 Wire without Neutral
ACTIVE
NEUTRAL
ACTIVE
MASTER
SLAVE
SW1
LOAD
NEUTRAL
NO NEUTRAL
SW2
NEUTRAL
ACTIVE
MASTER
SLAVE
SW1
LOAD
NEUTRAL
NO NEUTRAL
SW2
NEUTRAL
LOAD
6Two Way Switching
3 Wire with Neutral
For multi-way switching only use multiple Powermesh Light
Dimmer switches with master & slave configurations.
Never wire with normal switches for multi-way switching.
ACTIVE
NEUTRAL
ACTIVE
MASTER
SLAVE
SW1
LOAD
NEUTRAL
NO NEUTRAL
SW2
NEUTRAL
ACTIVE
MASTER
SLAVE
SW1
LOAD
NEUTRAL
NO NEUTRAL
SW2
NEUTRAL
NEUTRAL
LOAD
ACTIVE
7
ACTIVE
NEUTRAL
ACTIVE
MASTER
SLAVE
SW1
LOAD
NEUTRAL
NO NEUTRAL
SW2
NEUTRAL
ACTIVE
MASTER
SLAVE
SW1
LOAD
NEUTRAL
NO NEUTRAL
SW2
NEUTRAL
LOAD
NEUTRAL
ACTIVE
NEUTRAL
ACTIVE
MASTER
SLAVE
SW1
LOAD
NEUTRAL
NO NEUTRAL
SW2
NEUTRAL
ACTIVE
Three Way Switching
Set the
switch
positions
as shown.
Always use a Neutral wire where
possible for best performance.
Set the Neutral / No Neutral and
Master / Slave switches as shown
for ‘3 Wire with Neutral’.
Pair and setup with Zimi.
8Zimi Cloud Connect.
Requires Wi-Fi with Internet connection.
Remote access
anywhere.
Voice control
hands free.
Energy history
over time.
9
Want to learn more or need help?
support.zimi.life
Enjoy all the features and make your life easier.
Visit our website for tips, tricks and help.
Control a switch
from another switch.
Turn it on and off
any day or time.
Schedules
Monitor the power
usage and cost.
Energy Use
Turn it off
automatically.
Auto off Timer
Behaviour Link
10 Powermesh Status Indicator
Ready to pair.
‘Add device’ in Zimi to pair and complete setup.
Setup is complete.
This device has been paired and setup completed.
Action in progress.
This lets you know an automatic function is being activated.
Identify device.
This shows the device when updating its settings.
Device problem.
Please refer to support to resolve the problem.
If the device is working, the indicator has been
‘turned o’ in device settings.
Blue
White
Red
Off
White
pulsing
Blue & White
pulsing
11
• Download the Zimi App.
• Choose ‘Add Device’.
• Follow the on screen instructions.
Zimi App Download
Point your phone
camera at the QR code
to open the app store.
Enjoy the full experience
with all your Powermesh devices.
Manufacturer’s Warranty This product has been manufactured to the highest quality standards. This product is warranted
to the original purchaser and is not transferable. The product is guaranteed to be free from defects in workmanship and parts for a period
of 1 Year from the date of purchase. Defects that occur within this warranty period, under normal use and care will be repaired, replaced or
refunded. The benefits conferred by this warranty are in addition to all other rights and remedies of the consumer under a Commonwealth,
State and Territory laws in relation to the goods or services to which this warranty relates and Australian Consumer Law. Risk in regard to
the product to be repaired shall at all times remain with the Purchaser. The warranty is given on the condition that the product to which it
applies is used for the purpose and in the manner intended by its construction and for no other purposes whatsoever. GSM Innovations Pty
Ltd shall not be responsible for damage of any kind, caused by accidents, power surges, electrical storm damage, incorrect power current,
infestation (vermin or insect), incorrect installation, incorrect electricity or plumbing installation, improper use of controls or failure to use the
unit in accordance with the operating instructions, general misuse or abuse or from normal wear and tear. Any attempt by an unauthorised
person to repair or tamper with the equipment shall render the warranty null and void. Goods presented for repair under this warranty may
be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods. GSM
Innovations Pty Ltd’s liability under this warranty is limited to the replacement and/or repair of the defective parts within the warranty period
and does not extend to installation or removal of the product. Acceptance of liability by GSM Innovation Pty Ltd contained herein is to the
exclusion of any other remedy whatsoever and howsoever arising in respect of any equipment to which it applies.
Proof of Purchase Please keep your purchase docket or receipt as proof of purchase and as proof of the date on which the purchase
was made. The purchase docket or receipt must be presented with the warranty when making a claim under this warranty. Failure to produce
documentary proof of the date of original acquisition by the original Purchaser will result in a charge being levied for work done, labour and
parts supplied. Likewise a charge will be made for any calls following warranty claim where no fault is found with the unit.
Service during the warranty period The first point of contact for product issues is the place of purchase. The product must be returned
to the original place of purchase for product repair, replacement or refund. Please ensure the product is properly packaged so as to ensure
that no damage occurs to the product during transit and make sure that you have included an explanation of the problem. In the event of
goods requiring repair under manufacturer’s warranty the owner is responsible for the cost of transportation. Should the goods be found
to be in sound working order the owner might be charged a fee. This warranty is given by GSM Innovations Pty Ltd, 14 Millennium Circuit,
Helensvale, QLD 4212
Safety Warnings Read all instructions and safety information. All electrical work must only be undertaken after disconnection of the
power by removing fuses or turning off the circuit breaker, to ensure all pole disconnection from the electrical supply. All electrical
work must be carried out by a licensed and qualified electrician and in accordance to AS/NZS 3000 Wiring Rules and applicable
14 Millennium Circuit
Helensvale QLD 4212
Australia.
www.zimi.life
local authority regulations. This product is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of
the product by a person responsible for their safety. Young children should be supervised to ensure that they do not play with the unit.
Do not cut or notch joists, beams and rafters to install the unit. Do not damage hidden electrical wiring or utilities when cutting. The product
must be installed so that switches and other controls cannot be touched by a person in the bath or shower. Do not install the product in a
location where water will splash onto it. Check and confirm that all connections are proper and secure to prevent causing property damages
or injury. Do not install outdoor where it could be exposed to water or moisture (indoor use only).
Trademarks Zimi and Powermesh and their respective logos are registered trademarks of GSM Innovations Pty Ltd. Google and Google
Play are trademarks of Google LLC. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Apple, the Apple
logo, Apple Watch and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple
Inc., registered in the U.S. and other countries.
Copyright © 2021 GSM Innovations Pty Ltd. All rights reserved.

Powermesh_Multi_Dimmer_Switch_Installation_Instructions.pdf 230201

Powermesh_Power-Point_Installation_Instructions_A4.pdf 230201
Let’s get
connected.
Double Power Point.
Power Switch
Single press on / off
with indicator.
Power Socket
Each socket can
be controlled
independently.
Using the Power Point.
2
Mounting screws
Snap on cover
Reset Button
Powermesh Status Indicator
See overleaf for the meaning
of each colour status.
MAC ID
Unique product serial number.
Connect the wiring.
Surge protection is recommended at the main switchboard.
Products damaged by power surges are not covered by warranty.
3
Part Number: PMPP / PMPPBK
Line Voltage Frequency:
50Hz Nominal
Rated Load:
Maximum Load 10A
@ 250V / 2500W
Specifications
ACTIVE
EARTH
NEUTRAL
NEUTRALACTIVE
EARTH
Important - Read before installing.
Failure to follow these
instructions can result in
serious injury or death.
Must only be installed by a
LICENSED ELECTRICIAN
to local wiring regulations.
1
AVOID THE RISK OF ELECTRIC SHOCK
Once the product has been fastened to the wall,
ensure the supplied screw caps are inserted firmly
into the screw mounting holes.
Screw mounting holes
Factory Reset
Remove the cover and press the RESET
button until the Powermesh indicator flashes
blue. Release the button and when the
indicator turns blue, it’s ready to pair.
Zimi Cloud Connect.
Requires Wi-Fi with Internet connection.
5
Remote access
anywhere.
Voice control
hands free.
Energy history
over time.
Enjoy the full experience
with all your Powermesh devices.
6Want to learn more or need help?
support.zimi.life
Enjoy all the features to make your life easier.
Visit our website for tips, tricks and help.
Turn it on and off
any day or time.
Prevent power use
at the switch.
SchedulesPower Lock
Monitor the power
usage and cost.
Energy Use
Turn it off
automatically.
Auto off Timer
Powermesh Status Indicator.
7
Ready to pair.
‘Add device’ in Zimi to pair and complete setup.
Identify device.
This shows the device when updating its settings.
Energy alert.
This shows the device is using high power.
Device problem.
Please refer to support to resolve the problem.
If the device is working, the indicator has been
‘turned o’ in device settings.
Action in progress.
This lets you know an automatic function is being activated.
Setup is complete.
This device has been paired and setup completed.
Blue
White
Green pulsing
Red
Off
White
pulsing
Blue & White
pulsing
Pair and setup with Zimi.
4
• Download the Zimi App.
• Choose ‘Add Device’.
• Follow the on screen instructions.
Zimi App Download
Point your phone
camera at the QR code
to open the app store.
Manufacturer’s Warranty This product has been manufactured to the highest quality standards. This product is warranted
to the original purchaser and is not transferable. The product is guaranteed to be free from defects in workmanship and parts for a period
of 1 Year from the date of purchase. Defects that occur within this warranty period, under normal use and care will be repaired, replaced or
refunded. The benefits conferred by this warranty are in addition to all other rights and remedies of the consumer under a Commonwealth,
State and Territory laws in relation to the goods or services to which this warranty relates and Australian Consumer Law. Risk in regard to
the product to be repaired shall at all times remain with the Purchaser. The warranty is given on the condition that the product to which it
applies is used for the purpose and in the manner intended by its construction and for no other purposes whatsoever. GSM Innovations Pty
Ltd shall not be responsible for damage of any kind, caused by accidents, power surges, electrical storm damage, incorrect power current,
infestation (vermin or insect), incorrect installation, incorrect electricity or plumbing installation, improper use of controls or failure to use the
unit in accordance with the operating instructions, general misuse or abuse or from normal wear and tear. Any attempt by an unauthorised
person to repair or tamper with the equipment shall render the warranty null and void. Goods presented for repair under this warranty may
be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods. GSM
Innovations Pty Ltd’s liability under this warranty is limited to the replacement and/or repair of the defective parts within the warranty period
and does not extend to installation or removal of the product. Acceptance of liability by GSM Innovation Pty Ltd contained herein is to the
exclusion of any other remedy whatsoever and howsoever arising in respect of any equipment to which it applies.
Proof of Purchase Please keep your purchase docket or receipt as proof of purchase and as proof of the date on which the purchase
was made. The purchase docket or receipt must be presented with the warranty when making a claim under this warranty. Failure to produce
documentary proof of the date of original acquisition by the original Purchaser will result in a charge being levied for work done, labour and
parts supplied. Likewise a charge will be made for any calls following warranty claim where no fault is found with the unit.
Service during the warranty period The first point of contact for product issues is the place of purchase. The product must be returned
to the original place of purchase for product repair, replacement or refund. Please ensure the product is properly packaged so as to ensure
that no damage occurs to the product during transit and make sure that you have included an explanation of the problem. In the event of
goods requiring repair under manufacturer’s warranty the owner is responsible for the cost of transportation. Should the goods be found
to be in sound working order the owner might be charged a fee. This warranty is given by GSM Innovations Pty Ltd, 14 Millennium Circuit,
Helensvale, QLD 4212
Safety Warnings Read all instructions and safety information. All electrical work must only be undertaken after disconnection of the
power by removing fuses or turning off the circuit breaker, to ensure all pole disconnection from the electrical supply. All electrical
work must be carried out by a licensed and qualified electrician and in accordance to AS/NZS 3000 Wiring Rules and applicable
14 Millennium Circuit
Helensvale QLD 4212
Australia.
www.zimi.life
local authority regulations. This product is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of
the product by a person responsible for their safety. Young children should be supervised to ensure that they do not play with the unit.
Do not cut or notch joists, beams and rafters to install the unit. Do not damage hidden electrical wiring or utilities when cutting. The product
must be installed so that switches and other controls cannot be touched by a person in the bath or shower. Do not install the product in a
location where water will splash onto it. Check and confirm that all connections are proper and secure to prevent causing property damages
or injury. Do not install outdoor where it could be exposed to water or moisture (indoor use only).
Trademarks Zimi and Powermesh and their respective logos are registered trademarks of GSM Innovations Pty Ltd. Google and Google
Play are trademarks of Google LLC. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Apple, the Apple
logo, Apple Watch and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple
Inc., registered in the U.S. and other countries.
Copyright © 2021 GSM Innovations Pty Ltd. All rights reserved.

Powermesh_Switches_Installation_Instructions_A4.pdf 230201
Let’s get
connected.
Multi Purpose Switch.
Important - Read before installing.
1
Megger testing may lead to low readings due to electronic components so
disconnect all electronic devices before taking reading. Install the included
warning sticker with circuit detail in the main electrical switch board.
Surge protection is recommended at the main switchboard.
Products damaged by power surges are not covered by warranty.
Powermesh devices must only be connected
with the Active and Neutral from the same RCD.
Failure to follow these
instructions can result in
serious injury or death.
Must only be installed by a
LICENSED ELECTRICIAN
to local wiring regulations.
Switch
Push button switch
for on and off with
LED indicator.
Mounting Screws
Included on rear
of device.
Factory Reset
Press until indicator flashes
blue to restore factory
settings. When the indicator
turns blue, it’s ready to pair.
(remove cover)
Using the Multi Purpose Switch.
2
Powermesh
Status Indicator
See overleaf for the
meaning of each
colour status.
Snap on cover
MAC ID
Unique product
serial number.
(remove cover)
Identifying the switches.
3
LOAD 1
LOAD 2
LOAD 3
LOAD 4
LOAD 1
LOAD 2
LOAD 3
LOAD 1
LOAD 2
LOAD 1
1 Button
PMMPS1
PMMPS1BK
2 Button
PMMPS2
PMMPS2BK
3 Button
PMMPS3
PMMPS3BK
4 Button
PMMPS4
PMMPS4BK
111
43
21
223
Technical specifications.
4
Incandescent
Fluorescent
Exhaust fans /
small motors
LED
CFLs
Electronic
transformers
Standard iron core &
toroidal transformers
Compatible load types Rated Loads
5AX max
5A max
3 Wire
with
Neutral
Mode
2 Wire
without
Neutral
5AX max per channel,
10AX total max load
5AX max per channel,
channel 1 is 5A only.
See note below.
2 or 3 Wire Mode with Auto-Sensing.
5
2 Wire
without
Neutral
3 Wire
with
Neutral
NEUTRAL
LINE
LOAD 1
LOAD 4
LOAD 3
LOAD 2
NEUTRAL
ACTIVE
LOAD 1
NEUTRAL
LINE
LOAD 1
LOAD 4
LOAD 3
LOAD 2
NEUTRAL
ACTIVE
Always use a Neutral wire where possible. When operating without a neutral
connected, a small amount of power is used via LOAD 1 when switched off. This
may in some instances result with lights not completely turning off. Dimmable loads
might be fixed by increasing to at least 2 lights with a load >10W. Non-Dimmable
loads may require a bypass/load correction device fitted if the load is insufficient.
Pair and setup with Zimi.
6
• Download the Zimi App.
• Choose ‘Add Device’.
• Follow the on screen instructions.
Zimi App Download
Point your phone
camera at the QR code
to open the app store.
Multi-way Switching with Behaviour Link.
7
NEUTRAL
LINE
LOAD 1
LOAD 4
LOAD 3
LOAD 2
NEUTRAL
ACTIVE
NEUTRAL
LINE
LOAD 1
LOAD 2
NEUTRAL
ACTIVE
NEUTRAL
LINE
LOAD 1
NEUTRAL
ACTIVE
Any button
without load
can be linked to a
button with a load.
The Powermesh Multi Purpose Switch SHOULD NOT
be wired with any other type of switches.
‘Behaviour link’ buttons with the Zimi app.
This can be changed at any time.
The ‘Behaviour link’
feature makes multi-way
switching easy.
Buttons turn off and on
together when either
one is pressed.
Multi-way
switching.
Zimi Cloud Connect.
Requires Wi-Fi with Internet connection.
Remote access
anywhere.
Voice control
hands free.
Energy history
over time.
8
Enjoy the full experience
with all your Powermesh devices.
Want to learn more or need help?
support.zimi.life
Enjoy all the features to make your life easier.
Visit our website for tips, tricks and help.
Control a switch
from another switch.
Turn it on and off
any day or time.
Schedules
Monitor the power
usage and cost.
Energy Use
Turn it off
automatically.
Auto off Timer
Behaviour Link
9
10 Powermesh Status Indicator.
Ready to pair.
‘Add device’ in Zimi to pair and complete setup.
Setup is complete.
This device has been paired and setup completed.
Action in progress.
This lets you know an automatic function is being activated.
Identify device.
This shows the device when updating its settings.
Device problem.
Please refer to support to resolve the problem.
If the device is working, the indicator has been
‘turned o’ in device settings.
Blue
White
Red
Off
White
pulsing
Blue & White
pulsing
Manufacturer’s Warranty This product has been manufactured to the highest quality standards. This product is warranted
to the original purchaser and is not transferable. The product is guaranteed to be free from defects in workmanship and parts for a period
of 1 Year from the date of purchase. Defects that occur within this warranty period, under normal use and care will be repaired, replaced or
refunded. The benefits conferred by this warranty are in addition to all other rights and remedies of the consumer under a Commonwealth,
State and Territory laws in relation to the goods or services to which this warranty relates and Australian Consumer Law. Risk in regard to
the product to be repaired shall at all times remain with the Purchaser. The warranty is given on the condition that the product to which it
applies is used for the purpose and in the manner intended by its construction and for no other purposes whatsoever. GSM Innovations Pty
Ltd shall not be responsible for damage of any kind, caused by accidents, power surges, electrical storm damage, incorrect power current,
infestation (vermin or insect), incorrect installation, incorrect electricity or plumbing installation, improper use of controls or failure to use the
unit in accordance with the operating instructions, general misuse or abuse or from normal wear and tear. Any attempt by an unauthorised
person to repair or tamper with the equipment shall render the warranty null and void. Goods presented for repair under this warranty may
be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods. GSM
Innovations Pty Ltd’s liability under this warranty is limited to the replacement and/or repair of the defective parts within the warranty period
and does not extend to installation or removal of the product. Acceptance of liability by GSM Innovation Pty Ltd contained herein is to the
exclusion of any other remedy whatsoever and howsoever arising in respect of any equipment to which it applies.
Proof of Purchase Please keep your purchase docket or receipt as proof of purchase and as proof of the date on which the purchase
was made. The purchase docket or receipt must be presented with the warranty when making a claim under this warranty. Failure to produce
documentary proof of the date of original acquisition by the original Purchaser will result in a charge being levied for work done, labour and
parts supplied. Likewise a charge will be made for any calls following warranty claim where no fault is found with the unit.
Service during the warranty period The first point of contact for product issues is the place of purchase. The product must be returned
to the original place of purchase for product repair, replacement or refund. Please ensure the product is properly packaged so as to ensure
that no damage occurs to the product during transit and make sure that you have included an explanation of the problem. In the event of
goods requiring repair under manufacturer’s warranty the owner is responsible for the cost of transportation. Should the goods be found
to be in sound working order the owner might be charged a fee. This warranty is given by GSM Innovations Pty Ltd, 14 Millennium Circuit,
Helensvale, QLD 4212
Safety Warnings Read all instructions and safety information. All electrical work must only be undertaken after disconnection of the
power by removing fuses or turning off the circuit breaker, to ensure all pole disconnection from the electrical supply. All electrical
work must be carried out by a licensed and qualified electrician and in accordance to AS/NZS 3000 Wiring Rules and applicable
14 Millennium Circuit
Helensvale QLD 4212
Australia.
www.zimi.life
local authority regulations. This product is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of
the product by a person responsible for their safety. Young children should be supervised to ensure that they do not play with the unit.
Do not cut or notch joists, beams and rafters to install the unit. Do not damage hidden electrical wiring or utilities when cutting. The product
must be installed so that switches and other controls cannot be touched by a person in the bath or shower. Do not install the product in a
location where water will splash onto it. Check and confirm that all connections are proper and secure to prevent causing property damages
or injury. Do not install outdoor where it could be exposed to water or moisture (indoor use only).
Trademarks Zimi and Powermesh and their respective logos are registered trademarks of GSM Innovations Pty Ltd. Google and Google
Play are trademarks of Google LLC. Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Apple, the Apple
logo, Apple Watch and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple
Inc., registered in the U.S. and other countries.
Copyright © 2021 GSM Innovations Pty Ltd. All rights reserved.