PowerPac PPBL800 User manual

PROFESSIONAL HIGH POWER BLENDER with GLASS JUG 1200W
PPBL800

Parts & Description s
Blender Jug (Glass)
Motor unit
Sealing Ring
Jug Base
Pulse button
ON/OFF &
Speed Rotary
Knob
Blade Holder
Lid
Plug
Blender Blade assembly

Warnings s
ATTENTION :
Read this booklet carefully it contains important instructions for a safe installation,
use and maintenance.
Important instructions to be kept for future reference.
The following basic precautions should always be followed when using electrical
appliances:
1. Read all instructions before using the appliance.
The Appliance
2. This appliance must be used only for the purpose it was expressly designed; any
use NOT complying with the instructions contained in the manual is considered
inappropriate and dangerous. The manufacturer is NOT responsible for possible
damages caused by the inappropriate and/or unreasonable use.
3. The installation/assembly of the appliance will be made in accordance with the
indications of the manufacturer. A wrong procedure may cause damages to
persons, animals or objects, for which the manufacturer cannot be considered
responsible.
4. Before use, check the integrity of the appliance and power cable. DO NOT
operate the appliance at all when the Motor unit or Blender Blade Assembly is
damaged. In case you are not sure, contact a qualified person. If the power
cable is damaged, it must be replaced by the manufacturer / service agent or a
qualified technician in order to avoid a shock hazard.
5. Before powering the appliance make sure the rating (voltage and frequency)
corresponding to the grid and the socket is suitable for the plug of the appliance,
and that the wall socket is properly grounded.
6. Avoid the use of adapters and/or extension cables; if their use is absolutely
necessary, use only materials in compliance with the current safety regulations
and according to the electrical parameters of the adapters.
7. The appliance must NOT be switched on using external timers and/or other
remote control appliances which are not specified in this manual.
8. Only use original components & accessories provided by the manufacturer. Any
non-original components & accessories made by other manufacturers or by the
same manufacturer but for other models of the same capacity or otherwise, may
cause injuries to persons or damage to the appliance. Doing so will void the
warranty and may cause serious injury.
9. The packing materials (plastic bags, expanded polystyrene, etc.) must be kept
out of the reach of children or disabled persons since they represent potential
sources of danger.

Location
10. This appliance is NOT suitable to be used or stored near heat sources (open
flame, ovens, heaters, stoves, etc.) and/or in an explosive environment (in the
presence of flammable substances such as gas, vapour, mist or dust, in
atmospheric conditions when, after ignition, the combustion is spread in the air).
Items containing these substances should never be placed in the appliance, and
never be used to clean the appliance to avert the risk of fire or explosion.
11. Place the appliance at a proper distance from objects or surrounding walls
making sure that its functioning will not cause accidental damages. The
appliance should NOT be placed on a surface, or in the vicinity of objects, which
can be damaged by heat such as carpets or plastics. Never use the appliance
near curtains or textiles. If the appliance is operated on wooden furniture, use a
protective pad to prevent damage to delicate finishes.
12. Avoid placing the power cable on abrasive or sharp surfaces or in positions
where it can be damaged easily. Avoid placing heavy objects on the cable. The
cable must NOT be placed under carpets, or covered with throw rugs, runners or
similar. Arrange the cable away from the high traffic area, and where it will NOT
be tripped over. DO NOT pull or carry the appliance by the cable.
13. DO NOT use or store the appliance outdoors. Store and use the appliance only
indoors, or in any case, protected from weathering such as rain, direct radiation
of the sun and dust.
Operation
14. If you are using the appliance for the first time, you should:
a. Clean the exterior of the Motor unit with a damp cloth. Use a little detergent, if
necessary, and wipe dry. The Motor Unit may NOT be immersed in water.
Wash the Plug, Lid, Blender Jug, Blender Blade assembly (Blade Holder,
Sealing Ring & Jug Base) and utensils you wish to use with water &
detergent with a non-abrasive sponge. DO NOT use metal scouring pads nor
use solvents like paint thinners or acetone. Dry the accessories thoroughly.
b. Place the Base of the Motor unit on a flat, dry and heat-resistant surface.
Lock the Blender Blade assembly anti-clockwise onto the bottom of the
Blender Jug. Lower the Blender Jug onto the Motor unit – the Blender Jug
instantly locks onto the rotating mechanism – according to the instructions
listed in the section (“How to Use”) below. Check that these accessories are
locked into the Motor unit before you start using the appliance. Before adding
ingredients, make sure the blades are in place and are running smoothly.
Add food or liquids into the Blender Jug. Insert the Lid on top of the Blender
Jug. Insert the Plug on top of the Lid and turn clockwise to lock. Turn the
ON/OFF & Speed Rotary Knob to OFF (using dry hands). Attach the plug of
the appliance to the wall socket and switch on. Turn the ON/OFF & Speed
Rotary Knob clockwise between MIN and MAX or press the Pulse Button on
the Motor unit and the appliance will begin operation immediately.

Blend for NOT more than 2 minutes without interruption, resting for 5
minutes with a maximum of 3 cycles before resting for 15 minutes.
On completion of blending, turn the ON/OFF & Speed Rotary Knob to OFF,
switch off the wall switch and unplug the power cable. Wait for the blades to
stop turning, lift the Blender Jug with the Blender Blade assembly from the
Motor unit and detach from the Motor unit. Remove the Lid from the Blender
Jug and detach.
c. Make sure to remove any label or protective sheet which may prevent its
proper functioning.
DO NOT:
•cover the appliance during functioning;
•insert objects or body parts inside the protection cover of the appliance;
•overload the Blender Jug by filling it past the MAX volume (1800 ml) indicated.
The Jug should contain cut fruits and vegetables NO larger than 1 inch (2.5
cm) in length and thickness and must NOT contain dry food (food with
insufficient amount of water, very hard ingredients (such as coffee beans,
soybeans or rice), or foods or liquids with a temperature greater than 82 C
(180 F). Frozen fruits & vegetables, meat and even ice can be blended
without issue;
•allow hands, hair, clothing, curtains, spatulas and any other objects to come
into contact with the appliance’s motor and accessories to avoid personal
injury or damage to the machine when the appliance is in operation;
•place the appliance in the microwave oven or refrigerator, so as to avoid
damaging it;
•touch the blades as they are VERY SHARP! Hold the Jug Base of the Blender
Blade assembly while installing, removing or cleaning;
•detach the Blender Jug while the appliance is in operation;
Safety feature – the appliance will immediately stop working as the power is
disconnected. To start blending again, turn the ON/OFF & Speed Rotary Knob
to OFF, and then turn the ON/OFF & Speed Rotary Knob clockwise between
MIN and MAX;
•operate without the Lid being locked in place;
•operate the appliance for more than 2 minutes for blending without
interruption. Let the appliance rest between processing cycles for 5
minutes. After 3 processing cycles, allow an interval of 15 minutes to let
the appliance cool down before the next use so as to prolong its service
life. DO NOT allow the appliance to idle while in operation;
•turn the ON/OFF & Speed Rotary Knob too forcefully to avoid any damage;
•direct steam at any person or animal & one’s hands and face should be
angled away from the lid and pouring spout cap at all times to prevent
possible burns or scalding;
•leave the appliance unsupervised during operation.

15. During operation, DO NOT touch the appliance with wet body parts, and it is
recommended to have between you and the standing surface, an isolating
element (for example, wearing shoes with rubber soles).
16. DO NOT soak the Motor unit in water or other liquids, wash it under the tap, or
let any liquid flow into the internal casing of the appliance to prevent electric
shock. In case of accidental fall in water, DO NOT try to take it out, but first of all
switch the appliance off.
17. Switch the appliance OFF before unplugging the appliance. Plug and unplug the
power cable firmly holding it with dry hands. Always unplug the power cable
before changing accessories; to avoid overheating; if it is NOT used for a long
period and before storing, cleaning or performing any maintenance operation.
Remember that the blades may still be moving after the power cable is
unplugged! Prior to the latter, leave to cool for at least 10 minutes.
18. Wash the Plug, Lid, Blender Jug, Blender Blade assembly (Blade Holder, Sealing
Ring, Jug Base) and utensils immediately after usage to avoid build-up of
bacteria. (Warning: Blades are sharp!).
19. In the event the mixing of the food items produce bubbles, stop the operation
immediately and wait until the production of bubbles ceases before resuming
blending.
20. In case of malfunction or anomaly during the functioning such as smoke coming
out of the appliance, switch the appliance off immediately, turn off the power and
check the cause of the anomaly, if possible, with the support of a qualified
person.
21. This appliance is NOT intended for commercial use but to be used in households
and similar applications, such as:
•Staff kitchen areas in shops, offices and other working environments;
•By clients in dormitories hotels, motels and other residential environments;
•Bed and breakfast type environments.
22. This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall NOT play with the appliance. Cleaning and user
maintenance shall NOT be made by children unless they are older than 8 and
supervised. Keep the appliance and its cable out of reach of children less than 8
years old.
23. Save these instructions.
Safety Protection
If the appliance overheats, the thermal switch will be activated, leading to the
motor being shut off. Turn the ON/OFF & Speed Rotary Knob to OFF. Switch the
appliance off and unplug the power cable from the wall socket. Allow the
appliance to cool for at least 15 minutes before using the appliance.

How to use s
1. Clean the Motor unit and accessories before using. Refer to the section “How to
clean and maintain” immediately following this section.
Blender Jug (Glass)
Motor unit
Sealing Ring
Jug Base
Pulse button
ON/OFF &
Speed Rotary
Knob
Blade Holder
Lid
Plug
Blender Blade assembly

2. Place the Base of the Motor unit on a flat, dry and heat-resistant surface.
3. Lock the Blender Blade assembly anti-clockwise onto the bottom of the Blender
Jug.
4. Turn the ON/OFF & Speed Rotary Knob to OFF.
5. Lower the Blender Jug onto the Motor unit – the Blender Jug instantly locks onto
the rotating mechanism.
6. Wash the fruit/s and/or vegetables, then peel and cut into no larger than 1 inch
(2.5 cm) cubes. Add liquids such as water or milk, then place the cut fruits or
vegetables into the Blender Jug with the, topped off with yoghurt or ice cream if
desired. Frozen fruits, vegetables, meat and even ice can be blended without
issue. DO NOT overload the Blender Jug by overfilling it (past the 1800 ml line
on Blender Jug).
Note: For optimal performance, place the ingredients in the Blender Jug
according to the following sequence:
Liquids, fresh ingredients, frozen fruits, yoghurt, ice cream.
7. DO NOT place foods or liquids which are hotter than 82 C (180 F) in the
appliance. Allow very hot ingredients to cool before processing.
8. Insert the Lid on top of the Blender Jug.
9. Insert the Plug on top of the Lid and turn clockwise to lock. The Plug also serves
as a measuring cup when inverted. It has marks indicating 40, 55, 70 and 85 ml.
10. Plug the power cable into the wall socket and switch ON. Turn the ON/OFF &
Speed Rotary Knob clockwise between MIN and MAX or press the Pulse Button
and blend until the desired consistency is achieved. Whilst blending hot
ingredients, steam may emerge from the spout of the Blender Jug. DO NOT
direct steam at any person or animal & one’s hands and face should be angled
away from the Lid and spout at all times to prevent possible burns or scalding.
Place one hand on top of the Lid when blending to stabilise the appliance.
DO NOT operate the appliance for more than 2 minutes without
interruption. Let the appliance rest for 5 minutes between processing
cycles. After 3 processing cycles, allow an interval of 15 minutes to let the
appliance cool down before the next use, so as to prolong its service life.
DO NOT allow the product to idle while in operation.
11. On completion of blending, turn the ON/OFF & Speed Rotary Knob to OFF.
Switch off the wall switch and unplug the power cable. Wait for the blades to stop
turning.
12. Lift up the Blender Jug with the Blender Blade assembly from the Motor unit and
detach. Always allow the appliance to cool before removing parts and before
cleaning. Extreme caution must be used when moving the Blender Jug (or the
whole appliance) when the Blender Jug contains hot ingredients before or after
blending.
13. Remove the Lid from the Blender Jug and the contents may be poured out.

Crushing Ice
14. Before using the Blender to crush ice, make sure it is clean and rinse it out
thoroughly.
15. Ice cubes come in many shapes and sizes. Insert a maximum of 12 ice cubes
and add 60 ml of cold water. DO NOT be tempted to increase the number of ice
cubes and blend for longer –this will not work. Too much ice will never give you
satisfactory results.
16. Put the Lid and Plug on the Blender Jug (steps 8 & 9) and press the Pulse
Button for 2 seconds and release for 2 seconds. Note that too much blending will
reduce the ice to liquid, too little will merely chip the edges/corners off the ice.
DO NOT try to crush ice without adding water into the jug.
only if a Jam occurs: DO NOT continue blending if the blade is jammed.
Turn the ON/OFF & Speed Rotary Knob to OFF. Switch off the wall switch and
unplug the power cable.
Wait for the blades to stop turning. Remove the Lid from the Blender Jug and
clear the jam. Re-attach the Lid to the top of the Blender Jug
Occasionally, the blockage may require that the Blender Jug be detached from
the Motor unit before clearing. In this case, wait for the blades to stop turning.
Lft up the Blender Jug with the Blender Blade assembly from the Motor unit and
detach. Remove the Lid from the Blender Jug and clear the jam. Re-attach the
Lid on top of the Blender Jug. Lower the Blender Jug onto the Motor unit – the
Blender Jug instantly locks onto the rotating mechanism
Perform steps 10 – 13 again.

How to clean and maintain s
1. Turn the ON/OFF & Speed Rotary Knob to OFF. Switch the wall switch off and
unplug the power cable from the wall socket.
2. Before cleaning, please make sure the blades have stopped running.
3. Clean the Motor unit with a damp cloth. DO NOT immerse the Motor unit in water
or other liquids, and avoid spraying water, in order to avoid damage or leakage.
4. Wash the Plug, Lid, Blender Jug, Blender Blade assembly (Blade Holder, Sealing
Ring, Jug Base) and utensils before and after use with water & detergent with a
non-abrasive sponge to avoid build-up of bacteria. Blades are sharp! Dry the
components with a soft, dry cloth.
DO NOT use a steel wire sponge, abrasive cleaners or corrosive liquids such as
gasoline or acetone to clean the appliance & accessories.
Never attempt to sterilise any part of this appliance with hot water or steam by
utilising a steamer, frying pan, oven, microwave oven, kettle, etc.Ensure that the
appliance & accessories are clean, dry, and placed in dry and well-ventilated
storage. Avoid direct sunlight.
5. Reassemble the Blender Jug in the Motor unit, the Blender Blade assembly in
the Blender Jug, and then place the Lid & Plug onto the Blender Jug before
storing.
Auto Clean
6. Fill the Blender Bottle with warm water.
7. Press the Pulse Button for a few seconds to clean the Blender Bottle and
Blender Blade assembly very quickly and safely.

PROBLEM SOLVING s
Fault symptom
Cause analysis
Troubleshooting
After the Blender Jug or
is installed, the machine
does not work after
pressing the switch
Safety lock is not
connected
Reconnect the Motor unit
and the Blender Jug
The motor is
damaged or stuck
Turn the motor shaft. If it
still does not work, please
send to the nearest service
centre for inspection
Check if the power
cable is loose.
If the appliance still does
not work, replace with a
new power cable
When using the
appliance for the first
few times, the motor
gives off an unpleasant
smell
It is a normal
phenomenon when a
new motor is initially
used
The smell will disappear
with use
The blades get stuck
The blades are
entangled or stuck
by ingredients
Remove the Blender, take
out the ingredients, and cut
the ingredients into smaller
pieces or put less
ingredients
Refer to “only if a Jam
occurs” in “How to Use”
section for step-by-step
instructions
The appliance stops
working after a few
processing cycles
The motor was not
given enough time to
cool down between
processing cycles /
the motor was
allowed to idle while
in operation
Wait half an hour before
using the appliance. If it still
does not work, please send
to the nearest service
centre for inspection.
This is NOT covered by
Warranty

ENVIRONMENTAL TIP s
This appliance, along with all other electronic appliances, should, when it is no
longer capable of functioning, be disposed with the least possible environmental
damage according to the local regulations in your area. In most cases you can
discard the appliance at your local recycling centre.
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of
such waste separately for special treatment is necessary.
SPECIFICATION s
MODEL
VOLTAGE
POWER
PPBL800
220 –240V ~50 –60Hz
1200Hz

WARRANTY s
Warranty Conditions
1. This warranty provides against defective materials and manufacturing faults
throughout for two years from the date of purchase of the appliance. The
warranty on the Compressor is 10 years subject to the same conditions as
above.
2. This warranty also does not cover normal wear and tear, replacement of
consumable materials and accessories, and the cost of maintenance of the
appliance.
3. This warranty does not cover the repair or replacement of part/s damaged by
misuse, accidents, negligence, alterations, or modifications in any way, or repairs
done by any repair organisation without the prior consent of PowerPac Electrical
Pte Ltd.
4. Repair and service are to be performed at: 5 Changi South Lane #03-01
Singapore 486045. A transport fee will be charged for personal doorstep
service.
5. The original purchaser of the appliancemust furnish proof of purchase to our
Service Centre with the email or number as registered during submission of
warranty when this appliance is sent for repair/service. Failure to do so may
delay the receipt of said repair/service by the customer.
6. Under no circumstances whatsoever shall the serial number be erased, defaced
or altered by the customer and/or his representatives, or the dealer and/or his
agents. Failure to ensure this shall invalidate the warranty.
7. This warranty is deemed to be void if the defect is cause by the attack of
household pests, fire, lightning, natural disasters, pollution, abnormal voltage or
the usage of generators.
8. This warranty is valid in Singapore only.
9. This warranty will be honoured subject to the customer’s registration of the
warranty inclusive of original invoice or valid purchase receipt. Failure to present
these documents will result in denial of service. However, if the customer still
requests that the defective appliance be repaired, PowerPac Electrical Pte Ltd
may, at its discretion, repair the appliance but impose a labour charge, as well as
the costs of the replacement parts, to be borne solely by the customer.
10. Please refer to the attached picture for the location of
one of our appliance’s serial number, as an example.

Please complete the on-line registration warranty form available on our website.
There is no further requirement to send us any hard copy as part of our efforts to
save the environment.
In accordance with the terms and conditions of this limited warranty as stated above,
PowerPac Electrical Pte Ltd, at its expense shall provide free services for the
appliance within the warranty period from its date of purchase from our Authorised
dealers.