Poynting OMNI-232-02 User manual

Version: 1.1
Making wireless happen
OMNI-232-02
User Guide

2 A-OMNI-0232-02_PCL
Index
1. Packing Check List 4
2. Tools Required 5
3. Optional Accessories 6
4. Introduction 7
5. Installation Instructions 8
6. Routing Cables 11
7. Safety 12

Version: 1.1 3
Packing Check List
Item Description Quantity
1. A-OMNI-0232-02
Antenna only 1
2. M18 stainless steel
Nut 1
3. M18 Star washers 1
1
The appearance of each component
Antenna Unit
M18 Nut - SS
M18 Star Washer

4 A-OMNI-0232-02_PCL
Tools Required
Item
Safety goggles
Drills (Pilot drill
(3mm) and Hole
saw(20mm) or step
drill (4 - 20mm))
Masking tape
Hand drilling
machine
Centre punch
Hammer
27mm spanner/
wrench
Drilling template
(available on www.poynting.tech)
2

Version: 1.1 5
Optional Accessories
3
Optional Accessories
1. Various Cable extensions are
available

6 A-OMNI-0232-02_PCL
Introduction
4
This User Guide provides information on the
installation instructions of the OMNI-232-02
antenna.
Cable Conguration
Exploded View

Version: 1.1 7
Installation Instructions
Mounting the antenna
5
• Download the 1:1 drill template from
http://www.poynting.tech.
• Choosethemountinglocationcarefully.
Choose a position at least 50cm from
heat sources and with a clear line of
sight to the sky. It is recommended that
the antenna be installed at the highest
possible location on the vehicle’s roof
so that signal can be received in a
360° radius, clear of obstacles including
parts of the vehicle’s body and that the
mounting surface is as at as possible.
The selected location must have a
conductive metallic surface area
which is a minimum of ±400x400mm to
achieve optimal performance.
• Once you have decided on the
location and checked that there are
no obstructions such as cables or
channels below the mounting surface,
for the fastening nut and cables to
pass through, use the downloaded 1:1
drill template to mark the mounting
location.
• Topreventthemarkingtoolordrillsliding
off course, use masking tape over the
drilling point to help hold the drill point in
place. The masking tape also prevents
hot shavings from the drill or hole saw
which could penetrate and damage
the painted surface.
• Set the drilling machine to low speed
and carefully drill a pilot hole (Ø3mm
drilling bit works well). Use a Ø20mm
metal hole saw or step drill to open the
hole to the required size.

8 A-OMNI-0232-02_PCL
Note: The recommended drill hole
diameter for OMNI -232-02 is Ø20mm.
Go to: www.poynting.tech to download the scale 1:1 template.
• Clean the entire surface on which you
plan to mount the antenna. Cleaning is
donesoas nottodamage thevehicle’s
paint and to ensure good contact of
the foam surface to the mounting area.
Alcohol wipes can be used to remove
oil and dirt from the surface.
• Removethewaxprotectionpaperfrom
the adhesive foam seal at the base of
the antenna.
• Inserttheantennacablesandthreaded
spigot through the drilled hole.
• Push the antenna down onto the
mounting surface and make sure
the antenna is placed straight and
correctly.
• FittheM18starwasherandM18nutfrom
the inside of the mounting platform.
• Tighten the M18 Nut to 20Nm torque.
Be careful not to over tighten the nut.
Installation Instructions
5

Version: 1.1 9
Installation Instructions
Installation Drawing
6
NOTE: Torque specications:
Recommended fastening torque 20Nm
max tightening torque is 30Nm

10 A-OMNI-0232-02_PCL
• Survey the planned cable route
and look for any blocked passages.
Consider alternate routes to nd
the best available path. If extension
cables are needed, refer to the cable
conguration diagram. Always keep
the cables as short as possible to make
sure that minimum cable losses are
achieved.
• Tighten the cable’s SMA connectors
to 0.3-0.6Nm torque to ensure that
the OMNI-232-02 cables are properly
secured to the extension cables
Note: Take advantage of any existing
cable channels e.g., brake light opening
or wiring conduits to route the cables.
• Avoid running cables through
components or sharp apertures that
may cause excessive chang. Doing so
may erode the jacket and break signal
continuity.Also,avoidkinking,pinching,
or twisting a cable during a run.
• Use cable ties to secure the antenna
cables.
When handling the antenna cables, it is
essential you follow these basic rules:
• Never pull on the cable connectors;
pull only on the cable.
• Never run cables in a manner that
interferes with the driver’s ability to
safely operate the vehicle.
• Tighten the connectors that connect
to the modem/radio to 0.3-0.6NM to
ensure that the cables don’t rattle
loose.
Routing Cables
7

Version: 1.1 11
Safety
8
• If you are installing an antenna for
the rst time or unsure of how to install
your antenna, obtain the help of a
professional installer.
• Carefully survey the installation site
before installation to locate secure
hand holds, dangerous conditions (such
as power lines and weak roofs) and the
safest and most convenient placement
for ladders if necessary.
• When installing your antenna,
remember:
1. Do not install near power lines as
they can electrocute you.
2. Do not install on a wet or windy day,
or if there is lightning or thunder in
the area.
3. Wear shoes with rubber soles and
heels and protective clothing (long
sleeve shirt or jacket) and rubber
gloves.
4. Avoid operating while under the
inuence of drugs, alcohol or
medication.
5. Make sure that any loose tting
jewellery or clothing is secured
and tie back long hair as they can
get caught in moving parts during
installation.
6. If the antenna starts to fall, get away
from it and let it fall to avoid harm to
yourself.

12 A-OMNI-0232-02_PCL
• When drilling, remember to:
1. Use safety goggles when drilling the
holes.
2. Avoid using bits that are dull, bent
or damaged.
3. Be aware of where your ngers are
in relation to the drill bit when using
the drilling machine.
4. To stop the drilling machine, let the
drill chuck come to a complete
stop on its own. Do not grasp the
chuck in an attempt to stop the drill
bit.
5. Hold the drill correctly, as a sudden
slip could cause severe damage to
your hand.
CAUTION:
Antennas must be installed to provide
a separation distance of at least 20cm
from all persons so as to comply with SAR
(Specic Absorption Rate) RF Exposure
requirements.
European Waste Electronic Equipment Directive 2002/96/EC
Please ensure that old waste
electricals and electronics are recycled.
Directive 2011/65/EU (RoHS 2)
This product is fully compliant with the RoHS
2 directive.
Safety
8