Poynting PUCK-V1 User manual

Revision 2.0

2Revision 2.0

3Revision 2.0
1.
Packing Check List
4
2.
Introduction
9
3.
Antenna Mounting
Precautions
15
4.
Cable Routing
15
5.
Safety
16

4Revision 2.0
Item
Description
Quantity
1.
*PUCK-V1 Antenna Only
1
2.
M4 x 10mm Flat Head
Stainless Steel Screws
4
(Attached to
the antenna)
3.
35mm Threaded Spigot
1
(Attached to
the antenna)
4.
75mm Threaded Spigot
1
5.
Magnetic Base
1
6.
Pole/Wall Mount
Bracket
1
7.
Plastic Nut
1
(Attached to
the antenna)
8.
Adhesive Foam Seal
1
(Attached to
the antenna)
9.
Grip Extenders
5**
(Attached to
the antenna)
10.
SMA (F) to RP-SMA
(M) Adapter
2**
*Antenna will differ with different versions
**Quantity will differ with different versions

5Revision 2.0
Antenna Unit
M4 x 10mm Flat Head Stainless Steel Screws
35mm Threaded Spigot
75mm Threaded Female Spigot
Magnetic Base

6Revision 2.0
Pole/ Wall Mount Bracket
Plastic Nut
Adhesive Foam Seal
Grip Extenders
*SMA(F) to RP-SMA(M) Adapters
*Antenna with Wi-Fi only

7Revision 2.0
Drills (Pilot drill (3mm) and Hole saw (22mm)
or step drill (4-22mm))
Impact Drilling Machine
Hammer
Safety Goggles
27mm Spanner/Wrench

8Revision 2.0
Masking Tape
Centre Punch
Drilling Template
(Available on www.poynting.tech/downloads)

9Revision 2.0
This User Guide provides information on the
installation instructions of the Omni-directional
antenna (PUCK-V1 Series).
Threaded Spigot Mounting
Use the Drill template below or download the 1:1
drill template from
http://www.poynting.tech/downloads.
•Choose the mounting location carefully and a
position at least 50cm from heat sources,
with a clear line of sight to the sky.
•Once you have decided on the location and
checked that there are no obstructions such
as cables or channels below the mounting
surface, for the fastening nut and cables to
pass through, use the downloaded 1:1 drill
template to mark the mounting location.
•To prevent the marking tool or drill sliding off
course, use masking tape over the drilling
point to help hold the drill point in place. The
masking tape also prevents hot shavings
from the drill or hole saw which could
penetrate and damage the painted surface.
•Clean the entire surface on which you plan to
mount the antenna. Cleaning is done so as
not to damage the vehicle’s paint and to
ensure good contact of the foam surface to
the mounting area.
•Alcohol wipes can be used to remove oil and
dirt from the surface.
•The 35mm threaded Spigot should be used to
secure the antenna to a surface structure of
20mm thickness or less. Likewise, the 75mm
threaded Spigot should be used to secure the
antenna to a surface structure of 60mm
thickness or less.

10 Revision 2.0
Securing the antenna
•Fasten the required spigot with the Flat head
screws.
•Clean the plastic surface of the antenna base
and threaded spigot.
•Peel off one of the wax paper layers from the
foam seal and stick the foam seal to the
plastic surface.
•Carefully slide the cable through the hole.
•Peel off the second wax paper layer and
firmly press the antenna down onto the
surface.
•Tighten the nut so that it compresses the
foam seal.
Note: Be careful not to overtighten the nut.