Poynting OMNI-293 User manual

Version 2.0
OMNI-293
User Guide
South Africa
Unit 4, N1 Industrial Park
Landmarks Ave
Samrand, 0157
South Africa
Tel: [phone]
[email protected]
Europe
Kronstadler Straße 4,
81677 München
Germany
Tel: [phone]
Mob.: [phone]
[email protected]

3
Version 2.0
Index
1.
Packing Check List
4
2.
Introduction
7
3.
Antenna Mounting
Precautions
9
4.
Cable Routing
9
5.
Safety
10

4
1. Packing Check List
PCL-A-OMNI-0293
Item Description Quantity
1. A-OMNI-0293
Antenna only
1
2. M4 stainless steel
machine screw and
washer
4
3. Stainless steel
L-Bracket
1
4. Stainless steel
Econo bracket
2
5. M6x90mm stainless
steel U-Bolts
2
6. M6 Nyloc and
standard stainless
steel nuts
4
7. M6 stainless steel
atwashers
4
8. Easytwallplug
and screw
4

5
Version 2.0
Appearance of Components
Antenna Unit
Stainless Steel L-Bracket Assembly
M4 Machine Screws and M4 Flat Washers
Easy Fit Wall Plug and Screw
2
8
1
5
4
3
7
6

Tools which may be required:
6mm Masonry drill bit
Impact drilling machine
Screw driver-Cross slot/Philips
Hammer
PCL-A-OMNI-0293
6

2. Introduction
This User Guide provide information on
the installation instructions of the Omni-
directional antenna (A-OMNI-0293).
Antenna Configuration 1
Pole Mounting
Version 2.0 7
•Lay the antenna out at the installation
site and carefully assemble the
antenna to the L-bracket using the
provided bolts.
•Next place the U-bolts around the pole
and push both the econo brackets and
the assembled L-bracket through the U-
bolts. Tighten the nuts on the U-bolt until
the bracket is secured to the pole.
•Mount the antenna so that there is at
least 1 meter of clearance in all
directions around it and unobstructed
line of sight to the cell tower’s strongest
signal.

8PCL-A-OMNI-0293
Antenna Configuration 2
Wall Mounting
•This antenna should be mounted on a
wall using the wall plugs as shown in
thefigure below
•Strain relieve the cable to the wall with
saddles or cable tie to the closest
structure.
•Connect the end of cable to radio
device
Wall Plug
M4 screws

3. Antenna Mounting Precautions
•Place the antenna at the highest point
and ensure that there aren't any
surrounding obstructions to the antenna.
•In order to avoid communication
interference, ensure that the antenna is
placed at least 0.5m away from other
antennas and metal objects.
•Avoid installing the antenna near a
chimney, as the smoke and soot emitted
by the chimney can obstruct the signal
level achieved by the antenna.
•Install the antenna away from heat
sources and flammable gases.
4. Cable Routing
•Survey the planned cable route and look
for any blocked passages. Consider
alternate routes to find the best available
path. Always keep the cables as short as
possible to make sure that minimum cable
losses are achieved.
•Note: Take advantage of any existing
cable channels. e.g wiring conduits to
route the cables.
•Avoid running cables through components
or sharp apertures that may cause
excessive chafing. Doing so may erode the
jacket and break signal continuity. Also,
avoid kinking, pinching, or twisting a cable
during a run.
•Use cable ties to secure the antenna
cables.
Version 2.0 9

When handling the antenna cables, it is
essential you follow these basic rules:
•Never pull on the cable connectors;
pull only on the cable.
•Tighten the connectors and ensure
that the cables don’t rattle loose.
5. Safety
•If you are installing an antenna for the first
time or unsure about how to install your
antenna, obtain the help of a professional
installer.
•Carefully survey the installation site before
installation to locate secure handholds,
dangerous conditions (such as power lines
and weak roofs) and the safest and most
convenient placement for ladders if
necessary.
•The antenna may not be used as a climbing
or pulling device.
•Considerations must be taken when
mounting the antenna that people do not
hang or pull on it.
•When installing your antenna, remember:
1. Do not install near power lines as they can
electrocute you.
2. Do not install on a wet or windy day or
when there is lighting or thunder in the area.
3. Wear shoes with rubber soles and heels,
protective clothing (long sleeve shirt or
jacket) and rubber gloves.
4. Avoid installation while under the
influence of drugs, alcohol or medication.
10 PCL-A-OMNI-0293

5. Make sure that any loose-fitting jewellery
or clothing is secured and tie back long
hair as they can get caught in moving
parts during installation.
6. If the antenna assembly starts to fall, get
away from it and let it fall to avoid harming
yourself.
•When drilling, remember;
1. Use safety goggles when drilling the
holes.
2. Avoid using bits that are dull, bent
or damaged.
3. Be aware of where your fingers are
in relation to the drill bit when using
the drilling machine.
4. To stop the drilling machine, let the
drill chuck come to a complete
stop on its own. Do not grasp the
chuck in an attempt to stop the drill
bit.
5. Avoid awkward hand positions
where a sudden slip could cause a
hand to move into the drill bit or
cutting tool.
Version 2.0 11
CAUTION:
Antennas must be installed to provide
a separation distance of at least 20cm
from all persons so as to comply with SAR
(SpecicAbsorptionRate)RFExposure
requirements.
European Waste Electronic Equipment Directive 2002/96/EC
Please ensure that old waste
electricals and electronics are recycled.
Directive 2011/65/EU (RoHS 2)
This product is fully compliant with the RoHS
2 directive.