1. INTRODUCTION
2. TECHNICAL CHARACTERISTICS
3. ELECTRICAL CONNECTIONS DIAGRAM
With the aid of a
screwdriver, remove
the front cover.
NOTE: Before registering the switch in the application,
do this procedure with the equipment turned on
FLASHING
SLOWLY
FLASHING FAST
ON
WIPED OUT
LED:
-AP MODE
-EZ MODE
-REGISTRATION
-NO REGISTERED
WITHOUT WIFI
Inner part without front cover
TO RESET OR
SWITCH EZ/AP
MODE PRESS
THE SENSOR
UNTIL LED
FLASHES
RESET / MODE
SWITCH.
ATTENTION
DO NOT PLACE THE TOP WITH THE POWER ON AFTER
REGISTRATION IN THE APP SWITCH OFF THE POWER TO
PLACE THE FRONT COVER.
AFTER CHOOSING THE MODE,
GO BACK TO THE APP TO REGISTER
THE SWITCH
NF
The smart wi-fi touch switch has a touch sensor and a beautiful modern design
with a glass mirror. Possibility of using one or two lamps, it accepts commands
via the touch of the switch or via the "PPA ON" application, all with visual
feedback via the equipment's LED.
- Power: 90~240Vac automatic bivolt;
- Wi-fi communication: 802.11 b/g/n 2.4GHz standard;
- Dry contact type switching (C/NA);
- Dimensions: 120x72x33mm (HxWxD); - Weight: 180g;
- Finished in glass;
- 2 touch buttons;
- Standard 4 x 2;
- LED signage;
* Does not work with parallel switch.
WARNING:
Do not use the equipment
without referring to this
manual rst.
P30391 - 04/2022
Rev. 0
MANUAL
INTERRUPTOR T2
TOUCH SMART
CONNECTION EXAMPLE: LAMP 1
POWER
NEUTRAL
PHASE
LAMP 1 LAMP 2
aer entering the
code the App will
ask for register one
password.
Aer clicking on
obtain the verificaon
code it will be
requested.
It is in the email
informed
Register
Obtain the verication code
Registry
verication code
Registry verication code
To verify your registration account
The verication code has been sent
to your email address:
Set password
Use 6 to 20 characters, mixing letters and
numbers
Concluded
Step 3: Add a device, for this and turn off mobile data connect your
Smartphone to the 2.4GHz Wi-Fi network that the device will be
connected to. Turn on Bluetooth, turn on device location click '+' in
the upper right corner.
Electric Grid Voltage Minimum Power Maximum power
127 VCA 5 Watts 240 Watts
220 VCA 5 Watts 240 Watts
NOTE: For any other application other than lighting control, such as controlling a fan,
automated blind, among other purposes, the maximum load suggested is 5A.
TABLE OF POWER (LOAD) LIMITS FOR EACH OUTPUT
OF THE TOUCH SWITCH
4. REGISTRATION OF THE SWITCH ON
PPA ON APP
NF
NF
Step 1: To download the "PPA ON" app, go to the Play Store or App Store app
store.
NOTE: The application is not available for Windows Phone operating system
(Micrisoft) and other operating systems on the market, except the two mentioned
above.
Step 2: Login if you already have an account, if not, register in the application by
entering the necessary information, after registration, click on "get verification
code".
CONNECTION EXAMPLE: LAMP 2
CONNECTION EXAMPLE: LAMP 1 + LAMP 2
NEUTRAL
NEUTRAL
PHASE
PHASE
POWER
POWER
LAMP 1
LAMP 1
LAMP 2
LAMP 2
Login with an existing account
register
User Agreement and Privacy Policy
We understand the importance of
privacy. In order to fully present our
collection and use of your personal
information, we have thoroughly
reviewed our privacy policy and user
agreement in accordance with the
latest laws and regulations. By clicking
[Agree], it means that you have read,
understood and accepted the entire
updated Privacy Policy and User
Agreement. Please take some time to
familiarize yourself with our privacy
policy and if
Click Register soon
aer accept the
terms.
Not accepted Accepted
Introduction to the app:
GENERAL TERMS AND CONDITIONS OF WARRANTY
MOTOPPAR da Amazônia Indústria e Comércio de Eletrônicos
Ltda, registered with CNPJ No. 09.084.119/0002-45, located at
Praça Linear, No. 100, Bloco II, Centro, Santa Rita do Sapucaí/MG,
CEP 37.500-000, manufacturer of the PPA and CITROX products,
guarantees this device against defects in design, manufacture,
assembly and/or jointly and severally as a result of defects in the
quality of the material that make it inappropriate or unsuitable for the
consumption for which it is intended, for a legal period of 90 (ninety)
days from the date of purchase, provided that the installation
guidelines described in the instruction manual are observed.
As a result of the credibility and trust placed in PPA AND CITROX
products, we added another 275 days to the above period, reaching
a total of 1 (one) year, also counted from the date of purchase to be
proven by the consumer through the proof of purchase (Supervisor
Note).
In the event of a defect, within the warranty period, the liability of PPA
and/or CITROX is restricted to the repair or replacement of the
device manufactured by it, under the following conditions:
1. The repair and readjustment of the equipment can only be
carried out by the Technical Assistance, which is qualified to
open, remove, replace parts or components, as well as repair
the defects covered by the warranty, and, in the absence of
this and any use of parts not originals contained in the use, will
result in the waiver of this term by the consumer;
2. The warranty will not extend to accessories such as cables,
screws kit, fixing brackets, sources, etc.;
3. Expenses for packaging, transport and reinstallation of the
product are exclusively borne by the consumer;
4. The equipment must be sent directly to the company
responsible for the sale, representative of the manufacturer,
through the address on the purchase invoice, properly
packaged, thus avoiding the loss of warranty;
5. The replacement or repair of the equipment does not extend
the warranty period.
This warranty will be void if the product:
1. Suffer damages caused by agents of nature, such as
atmospheric discharges, floods, fires, landslides, etc.;
2. It is installed in an improper electrical network or even in
disagreement with any of the installation instructions set out in
the manual;
3. Defects caused by falls, blows or any other physical accident;
4. For violation of the equipment or attempt to repair by
unauthorized personnel;
5. It is not used for its intended purpose;
6. Not used under normal conditions;
7. Suffer damage caused by accessories or equipment attached
to the product.
Recommendation:
We recommend the installation and maintenance of the product by a
specialized technical service.
If the product has a defect or abnormal operation, look for a
specialized Technical Service for the necessary corrections.
Made by:
Motoppar da Amazônia Indústria e Comercio de Eletrônicos LTDA
Praça Linear, 100, Bloco 2 - Centro
Santa Rita do Sapucaí - MG - CEP 37540-000 - Brasil
CNPJ: 09.084.119/0002-45
www.ppa.com.br | +55 14 3407 1000
Step 4: Enter the WiFi network and password the device will connect to.
Click next.
Make sure your device is reset and
in EZ Mode (LED flashing quickly /
2 mes per second). If not, press
and hold the reset buon unl the
LED flashes quickly.
Light Switch
No device
Add Manually
Universal
Smart
Control
Smart Alarm Smart Relay
Module
Smart IP
HD câmera
Electrifier
Light Switch Wi-fi Plug Lamp
Cancel
Cancel
Cancel Cancel
Cancel
EZ Mode
Restart device first
If the indicator is flashing quickly, skip the reset
step.
On
Press the PROG button for 5 seconds
Make sure the indicator light is flashing quickly.
Restart devices
Confirm that the indicator flashes
quickly
Next
Next
Select a 2.4GHz Wi-Fi network
and enter the password.
If your Wi-Fi is 5GHz, set it to 2.4GHz
before proceeding. Common Router
Configuration Method
Products_2.4GHz
productscx2
Add Device
Add Device
Make sure the Wi-Fi signal is stable
Make sure the Wi-Fi signal is stable
Analyze
the devices
Analyze
the devices
Register the
device on
the Cloud
Register the
device on
the Cloud
Start
the device
Start
the device
Successfully added
Device successfully added.
Concluded
Make sure your device is reset, to enter AP Mode (LED flashing slowly 1
me per second), tap EZ Mode in the app to change the mode. If not
reset, press and hold the reset buon unl the LED flashes slowly.
Interruptor
Edit (inf. and general
conf. of the module)
Interruptor
Key 1 Key 2
Alterando o nome do disposivo
to rename the device tap it and then click
edit in sequence.
Share device with other users
«Share device» and «Add sharing» «number
or email»
Remove device just click and go
1
2
ATTENTION !! IF THE DEVICE REGISTRATION PROCEDURE THROUGH
THE EZ MODE IS NOT SUCCESSFULLY CARRIED OUT, IT WILL BE
NECESSARY TO REGISTER THROUGH THE AP MODE.
Step 5: Enter add device again. Enter the Wi-Fi network and password
the device will connect.
Click next.
Interruptor
Cancel
Cancel Cancel
Select a 2.4GHz Wi-Fi network
and enter the password.
Select a 2.4GHz Wi-Fi network
and enter the password.
If your Wi-Fi is 5GHz, set it to 2.4GHz
before proceeding. Common Router
Configuration Method
If your Wi-Fi is 5GHz, set it to 2.4GHz
before proceeding. Common Router
Configuration Method
Cloudy
26ºC
Temp. outdoor
58.0%
Humidity outdoor
919.2hPa
Pressure
All Devices
Light Switch
My Page Inteligent Me
Light Switch
All On Schedule Timer All Off
Light switch
Device informaon
Instant Scene and Operator
Device Offline Noficaon
Others
Offline Noficaon
Device sharing
Create group
FAQ and Feedback
Add to home screen
Check Network
Device update
Check Now
Is the latest version
Remove device
Add Share
Country / region
Account
Number
PPA PPA
Password
Next Next
Okay, now you can use your smart wi-fi touch switch
through the app.
Aer connecng to the switch, the App will ask you to login to the local
network (Smartlife-XXXX) that it will make available, aer connecng to
the local network, go back to the applicaon to connue the switch
registraon.
Your device has been successfully added, then tap Done.
Light switch
Cancel
Cancel Cancel
Cancel Cancel
EZ Mode AP Mode
AP Mode
AP Mode
Cancel
Restart device
Restart device
Restart device Restart device
Turn on the device.
Turn off aer 10s and turn on again
Back
Back
Back Back
Next
Next
Next Next
Press the boon RESET for 5s. Confirm that the indicator is flashing
slowly.
Then proceed to the next step.
Press the boon RESET for 5s again
unl the indicator flash slowly
Check if the indicator is flashing
slowly.
Conect the telefone Wi-Fi to hotspot
device
1 Telephone conected access point showing
below
2 Retorn to the app and continue add devices
Connect now
Active
Atual network
Avalible network
Atual network
PPA
Concluded
Successfully added
Device added successfully
TREINAMENTO PPA
MK Produtos PPA
MK Produtos PPA 5G
1. INTRODUCTION
2. TECHNICAL CHARACTERISTICS
3. ELECTRICAL CONNECTIONS DIAGRAM
With the aid of a
screwdriver, remove
the front cover.
NOTE: Before registering the switch in the application,
do this procedure with the equipment turned on
FLASHING
SLOWLY
FLASHING FAST
ON
WIPED OUT
LED:
-AP MODE
-EZ MODE
-REGISTRATION
-NO REGISTERED
WITHOUT WIFI
Inner part without front cover
TO RESET OR
SWITCH EZ/AP
MODE PRESS
THE SENSOR
UNTIL LED
FLASHES
RESET / MODE
SWITCH.
ATTENTION
DO NOT PLACE THE TOP WITH THE POWER ON AFTER
REGISTRATION IN THE APP SWITCH OFF THE POWER TO
PLACE THE FRONT COVER.
AFTER CHOOSING THE MODE,
GO BACK TO THE APP TO REGISTER
THE SWITCH
NF
The smart wi-fi touch switch has a touch sensor and a beautiful modern design
with a glass mirror. Possibility of using one or two lamps, it accepts commands
via the touch of the switch or via the "PPA ON" application, all with visual
feedback via the equipment's LED.
- Power: 90~240Vac automatic bivolt;
- Wi-fi communication: 802.11 b/g/n 2.4GHz standard;
- Dry contact type switching (C/NA);
- Dimensions: 120x72x33mm (HxWxD); - Weight: 180g;
- Finished in glass;
- 2 touch buttons;
- Standard 4 x 2;
- LED signage;
* Does not work with parallel switch.
WARNING:
Do not use the equipment
without referring to this
manual rst.
P30391 - 04/2022
Rev. 0
MANUAL
INTERRUPTOR T2
TOUCH SMART
CONNECTION EXAMPLE: LAMP 1
POWER
NEUTRAL
PHASE
LAMP 1 LAMP 2
aer entering the
code the App will
ask for register one
password.
Aer clicking on
obtain the verificaon
code it will be
requested.
It is in the email
informed
Register
Obtain the verication code
Registry
verication code
Registry verication code
To verify your registration account
The verication code has been sent
to your email address:
Set password
Use 6 to 20 characters, mixing letters and
numbers
Concluded
Step 3: Add a device, for this and turn off mobile data connect your
Smartphone to the 2.4GHz Wi-Fi network that the device will be
connected to. Turn on Bluetooth, turn on device location click '+' in
the upper right corner.
Electric Grid Voltage Minimum Power Maximum power
127 VCA 5 Watts 240 Watts
220 VCA 5 Watts 240 Watts
NOTE: For any other application other than lighting control, such as controlling a fan,
automated blind, among other purposes, the maximum load suggested is 5A.
TABLE OF POWER (LOAD) LIMITS FOR EACH OUTPUT
OF THE TOUCH SWITCH
4. REGISTRATION OF THE SWITCH ON
PPA ON APP
NF
NF
Step 1: To download the "PPA ON" app, go to the Play Store or App Store app
store.
NOTE: The application is not available for Windows Phone operating system
(Micrisoft) and other operating systems on the market, except the two mentioned
above.
Step 2: Login if you already have an account, if not, register in the application by
entering the necessary information, after registration, click on "get verification
code".
CONNECTION EXAMPLE: LAMP 2
CONNECTION EXAMPLE: LAMP 1 + LAMP 2
NEUTRAL
NEUTRAL
PHASE
PHASE
POWER
POWER
LAMP 1
LAMP 1
LAMP 2
LAMP 2
Login with an existing account
register
User Agreement and Privacy Policy
We understand the importance of
privacy. In order to fully present our
collection and use of your personal
information, we have thoroughly
reviewed our privacy policy and user
agreement in accordance with the
latest laws and regulations. By clicking
[Agree], it means that you have read,
understood and accepted the entire
updated Privacy Policy and User
Agreement. Please take some time to
familiarize yourself with our privacy
policy and if
Click Register soon
aer accept the
terms.
Not accepted Accepted
Introduction to the app:
GENERAL TERMS AND CONDITIONS OF WARRANTY
MOTOPPAR da Amazônia Indústria e Comércio de Eletrônicos
Ltda, registered with CNPJ No. 09.084.119/0002-45, located at
Praça Linear, No. 100, Bloco II, Centro, Santa Rita do Sapucaí/MG,
CEP 37.500-000, manufacturer of the PPA and CITROX products,
guarantees this device against defects in design, manufacture,
assembly and/or jointly and severally as a result of defects in the
quality of the material that make it inappropriate or unsuitable for the
consumption for which it is intended, for a legal period of 90 (ninety)
days from the date of purchase, provided that the installation
guidelines described in the instruction manual are observed.
As a result of the credibility and trust placed in PPA AND CITROX
products, we added another 275 days to the above period, reaching
a total of 1 (one) year, also counted from the date of purchase to be
proven by the consumer through the proof of purchase (Supervisor
Note).
In the event of a defect, within the warranty period, the liability of PPA
and/or CITROX is restricted to the repair or replacement of the
device manufactured by it, under the following conditions:
1. The repair and readjustment of the equipment can only be
carried out by the Technical Assistance, which is qualified to
open, remove, replace parts or components, as well as repair
the defects covered by the warranty, and, in the absence of
this and any use of parts not originals contained in the use, will
result in the waiver of this term by the consumer;
2. The warranty will not extend to accessories such as cables,
screws kit, fixing brackets, sources, etc.;
3. Expenses for packaging, transport and reinstallation of the
product are exclusively borne by the consumer;
4. The equipment must be sent directly to the company
responsible for the sale, representative of the manufacturer,
through the address on the purchase invoice, properly
packaged, thus avoiding the loss of warranty;
5. The replacement or repair of the equipment does not extend
the warranty period.
This warranty will be void if the product:
1. Suffer damages caused by agents of nature, such as
atmospheric discharges, floods, fires, landslides, etc.;
2. It is installed in an improper electrical network or even in
disagreement with any of the installation instructions set out in
the manual;
3. Defects caused by falls, blows or any other physical accident;
4. For violation of the equipment or attempt to repair by
unauthorized personnel;
5. It is not used for its intended purpose;
6. Not used under normal conditions;
7. Suffer damage caused by accessories or equipment attached
to the product.
Recommendation:
We recommend the installation and maintenance of the product by a
specialized technical service.
If the product has a defect or abnormal operation, look for a
specialized Technical Service for the necessary corrections.
Made by:
Motoppar da Amazônia Indústria e Comercio de Eletrônicos LTDA
Praça Linear, 100, Bloco 2 - Centro
Santa Rita do Sapucaí - MG - CEP 37540-000 - Brasil
CNPJ: 09.084.119/0002-45
www.ppa.com.br | +55 14 3407 1000
Step 4: Enter the WiFi network and password the device will connect to.
Click next.
Make sure your device is reset and
in EZ Mode (LED flashing quickly /
2 mes per second). If not, press
and hold the reset buon unl the
LED flashes quickly.
Light Switch
No device
Add Manually
Universal
Smart
Control
Smart Alarm Smart Relay
Module
Smart IP
HD câmera
Electrifier
Light Switch Wi-fi Plug Lamp
Cancel
Cancel
Cancel Cancel
Cancel
EZ Mode
Restart device first
If the indicator is flashing quickly, skip the reset
step.
On
Press the PROG button for 5 seconds
Make sure the indicator light is flashing quickly.
Restart devices
Confirm that the indicator flashes
quickly
Next
Next
Select a 2.4GHz Wi-Fi network
and enter the password.
If your Wi-Fi is 5GHz, set it to 2.4GHz
before proceeding. Common Router
Configuration Method
Products_2.4GHz
productscx2
Add Device
Add Device
Make sure the Wi-Fi signal is stable
Make sure the Wi-Fi signal is stable
Analyze
the devices
Analyze
the devices
Register the
device on
the Cloud
Register the
device on
the Cloud
Start
the device
Start
the device
Successfully added
Device successfully added.
Concluded
Make sure your device is reset, to enter AP Mode (LED flashing slowly 1
me per second), tap EZ Mode in the app to change the mode. If not
reset, press and hold the reset buon unl the LED flashes slowly.
Interruptor
Edit (inf. and general
conf. of the module)
Interruptor
Key 1 Key 2
Alterando o nome do disposivo
to rename the device tap it and then click
edit in sequence.
Share device with other users
«Share device» and «Add sharing» «number
or email»
Remove device just click and go
1
2
ATTENTION !! IF THE DEVICE REGISTRATION PROCEDURE THROUGH
THE EZ MODE IS NOT SUCCESSFULLY CARRIED OUT, IT WILL BE
NECESSARY TO REGISTER THROUGH THE AP MODE.
Step 5: Enter add device again. Enter the Wi-Fi network and password
the device will connect.
Click next.
Interruptor
Cancel
Cancel Cancel
Select a 2.4GHz Wi-Fi network
and enter the password.
Select a 2.4GHz Wi-Fi network
and enter the password.
If your Wi-Fi is 5GHz, set it to 2.4GHz
before proceeding. Common Router
Configuration Method
If your Wi-Fi is 5GHz, set it to 2.4GHz
before proceeding. Common Router
Configuration Method
Cloudy
26ºC
Temp. outdoor
58.0%
Humidity outdoor
919.2hPa
Pressure
All Devices
Light Switch
My Page Inteligent Me
Light Switch
All On Schedule Timer All Off
Light switch
Device informaon
Instant Scene and Operator
Device Offline Noficaon
Others
Offline Noficaon
Device sharing
Create group
FAQ and Feedback
Add to home screen
Check Network
Device update
Check Now
Is the latest version
Remove device
Add Share
Country / region
Account
Number
PPA PPA
Password
Next Next
Okay, now you can use your smart wi-fi touch switch
through the app.
Aer connecng to the switch, the App will ask you to login to the local
network (Smartlife-XXXX) that it will make available, aer connecng to
the local network, go back to the applicaon to connue the switch
registraon.
Your device has been successfully added, then tap Done.
Light switch
Cancel
Cancel Cancel
Cancel Cancel
EZ Mode AP Mode
AP Mode
AP Mode
Cancel
Restart device
Restart device
Restart device Restart device
Turn on the device.
Turn off aer 10s and turn on again
Back
Back
Back Back
Next
Next
Next Next
Press the boon RESET for 5s. Confirm that the indicator is flashing
slowly.
Then proceed to the next step.
Press the boon RESET for 5s again
unl the indicator flash slowly
Check if the indicator is flashing
slowly.
Conect the telefone Wi-Fi to hotspot
device
1 Telephone conected access point showing
below
2 Retorn to the app and continue add devices
Connect now
Active
Atual network
Avalible network
Atual network
PPA
Concluded
Successfully added
Device added successfully
TREINAMENTO PPA
MK Produtos PPA
MK Produtos PPA 5G
