PPA F32 PLUS Instruction manual

F32 PLUS PHOTOCELL
Rev. 1
TECHNICAL CHARACTERISTICS
• Compatible with all control boards on the market;
• Maximum reach:
• - External Area: up to 32 meters;
• - Internal Area: up to 40 meters;
• Power Supply Voltage: 12 to 24Vdc;
• Maximum current consumption: 65mA;
• Output NA, NF and pulsed (configurable);
• Immediate activation;
• Digital and microcontrolled technology;
• Immune to noise;
• LED indicative of tuning;
• Resistant to bad weather.
PHOTOCELL PRECAUTIONS
• Avoid installing the receiver unit directly
facing the sun;
• Make sure the cable outlet is down;
• Install the photocell away from obstructions
that may obstruct the beam;
• When using the product on a smooth or
polished floor (surfaces with high light
reflection), install the photocell at least 40
cm high from the floor. This will prevent
the reflection of the floor from affecting the
proper functioning of the sensor.
LED SIGNALING ON THE RECEIVER PLATE
LED on: Photocell misaligned (with obstruction)
LED off: Photocell aligned (no obstruction)
WARRANTY TERM
MOTOPPAR, Indústria e Comércio de Automatizadores Ltda., Located at Av. Labieno
da Costa Machado, nº 3526, Industrial District, Garça / SP, CEP 17400-000, CNPJ 52.605.821
/ 0001-55, IE 315.011.558.113 guarantees this against defects in design, manufacture and
assembly, and / or jointly and severally as a result of defects in the quality of the material that
makes it improper or inappropriate for the intended use for a legal term of ninety (90) days
from the date of acquisition.
Provided that the installation guidelines described in the operating instructions are
observed. In the event of a defect, during the warranty period, MOTOPPAR’s liability is limited
to the repair or replacement of the apparatus of its manufacture.
As a result of the credibility and trust deposited in the PPA products, we added to the above term
another 275 days, reaching a total of 1 (one) year, also counted from the date of acquisition to be
proven by the consumer through the proof of purchase.
In the additional time of 275 days, visits and transportation will be charged in locations where
there are no authorized services. The costs of transporting the appliance and / or technician are also
borne by the consumer owner.
A substituição ou conserto do equipamento não prorroga o prazo de garantia.
This warranty will lose its effect if the product:
- Suffer damage caused by accidents or agents of nature, such as lightning, flooding,
landslides, etc .;
- It is installed in an improper electrical network or even in disagreement with any of the
installation instructions stated in the manual;
- it is not used for its intended purpose;
- it is not used under normal conditions;
- Suffer damage from accessories or equipment attached to the product.

INSTALLATION
Step 1:Secure the transmitting and receiving units, aligned with each other, to a minimum height of 30 cm
from the floor and so that the wires are down to avoid possible water infiltration.
Step 2:Select the mode of operation of the
photocell via the jumpers detailed below.
Jumpers on Receiver
Jumper INV: This jumper reverses the relay
operating state.
• Closed: Normal Operation (factory
default).
• Open: Reverses the Relay Status (In this
situation, the relay remains activated
while the photocell is aligned, ie the NO
becomes NF and vice versa).
Jumper P/RL: Selects the operation mode of the
photocell, relay contacts (NA or NF) or pulsed.
NOTE! If the pulse mode is
selected, the INV jumper becomes
useless.
Jumpers on Transmitter
They select the maximum working distance of
the photocell.
Jumper 01: 0 to 5 meters
Jumper 02: 5 to 15 meters
Jumper 03: From 15 to 40 meters (if it is external
area, those 40 meters become 32 meters)
Step 3: Power the transmitter and receiver
boards with power from the operator command
board or from an external source, observing the
polarity on the red wire (+) and brown wire (-).
RECEIVER CONECTIONS
If you chose to use the Relay (Jumper in RL)
In case of a NO circuit, when the photocell is
obstructed, it will close the contact with the C,
and consequently activate the device.
In case of NF circuit, when the photocell is
obstructed, it will open the contact with the C,
and consequently will deactivate the device.
NOTE! It is mandatory that the
Jumper P / RL is set to operate the
relay mode, ie the jumper RL is closed.
If you choose to use the Pulsating mode (Jumper in P)
Onde:
GND = Alimentação negativa (-) da central de
comando do automatizador.
VCC = Alimentação positiva (+) da central de
comando do automatizador.
FOT = Entrada da fotocélula da central de
comando do automatizador.
NOTE! It is mandatory that the
Jumper P / RL is set to operate the
Pulsed mode, ie the jumper P closed.
NOTE! When the photocell is
used in the pulsed mode and with
power from an external source, the
GND (negative) of the source must be
connected to the GND of the control
center.
TRANSMITTER BOARD
RECEIVER BOARD
FOT - PHOTOCELL INPUT OF THE
COMMAND BOARD
DEVICE
INPUT
NO
C
NF
NO
C
NF
INPUT
DEVICE
NO
C
NF