Precision Power PP36L-12K-3 User manual

1
4REV 01-03-2023
REV 01-03-2023
FCC NOTICE
This equipment has been tested and found to comply with the
limit for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with these instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by tuning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures: (1) Reorient or relocate the receiving
antenna. (2) Increase the separation between the equipment
and receiver. (3) Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. (4)
Consult the dealer or an experienced radio/TV technician for
help.
CAUTION: Any changes or modifications could void the
authority granted by the FCC to operate this equipment.
NOTE: Precision Power reserves the right to change or correct
the contents of this document and does not assume any
responsiblity for ommissions or errors.
WARNING
Review the following important safety warnings to avoid bodily injury or
damage to equipment during installation or operation of this device. Read
ALL instructions before attempting to install or operate this device.
This device is intended for indoor use only. To prevent the risk
of fire or electrical shock, install in dry location free from damp or
wet environment, or potentially damp or wet environment.
Adhere to all acceptable operating environment limitations as
listed to prevent the risk of fire or electrical shock (see user
specifications within User’s Manual)
Risk of fire or explosion if improper battery is installed and
attempted to operate within this device. Device is rated and
approved for use with. Follow User Manual instructions for
proper installation of battery. Dispose of used batteries in
accordance to battery manufacturer specifications.
NO user-replaceable parts within this device except the battery.
Do not remove cover unless you are installing, replacing, or
servicing the battery.
Keep Out of reach of children.
If you experience problems with the device, discontinue use and
unplud from the AC socket. Call your provider for assistance.
!
!
!
!
!
!
PRECISION POWER, LLC
A PRECISION GROUP COMPANY
P: [phone]
E: [email protected]
Website: www.GoPrecisionGroup.com
MICRO UPS INTRODUCTION
MICRO UPS is designed and intended for use as a Desktop
or Wall-Mount uniterruptable 12Vdc power supply and
battery backup device for 12Vdc CPE Equipment (i.e. ONT,
Router, Access Point). The MICRO UPS not only provides
constant supply of DC power during normal operating
conditions, but offers battery backup power in case of
electrical power outage.
CONTENTS OF DESKTOP PRO PACKAGE
NOTE: Please verify all standard contents are accounted for
upon receipt of Micro UPS.
STANDARD: (1) Power Supply/Charger; (3) Li Ion Battery
Pack; (1) AC Power Cord; (1) 7-Pin Connector; (1) User’s
Manual; (1) 2 Position Wall Mount Plate; (1) DC Output Cord
Optional: (1) Universal Wall Mount Enclosure w/ Cover.
Model # PP36L-12K-3
User’s Manual

2 3
REV 01-03-2023
REV 01-03-2023
VISUAL INDICATORS
iand izna wijjsj nnakak n kandl nnall ajiwnn nnnla
-10° C - 49° C (14° F - 120.2°) at full power
0 - 95% noncondensing within enclosure
10,000 ft (3,000 m)
-30° C - 65° C (-22° F - 149° F)
BATTERY REPLACEMENT
As long as AC line power is available, the MICRO UPS can
operate while the battery pack is replaced
Procedure: Remove the MICRO UPS Battery Pack by sliding
off in opposite direction of installation (Fig.1) and follow
directions above for installing new MICRO UPS Battery Pack.
(Fig.5)
Fig. 5
INSTALLATION PROCEDURE
A. Slide MICRO UPS Battery Pack onto MICRO UPS Power
Supply until MICRO UPS Battery Pack becomes fully ush
with the top of the MICRO UPS Power Supply. (Fig.1)
- Next, slide onto backplate as shown in cover photo; with
power supply and 1 battery on one side and stack of 2
batteries on the other side.
B. Connect provided AC Power Cord to AC Input Connector
on bottom of the MICRO UPS Power Supply (Fig 2).
C. Connect 3 Prong AC Power Cord Plug End into standard
3 Prong AC Receptacle rated for NEMA 5-15, 3 Prong AC
Plug.
D. Verify “System Status”
LED is “On” with Green
illumination (Fig. 3).
E. Connect Micro UPS to ONT (Optical Network Terminal)
or other 12Vdc CPE Device using cable supplied or made
by your network provider. Do not exceed the ouput ratingas
provided in the technical specifications (Fig. 4)
F. Ensure “System Status”
LED is the only illuminated
LED on the MICRO UPS.
If any additional LEDs are
illuminated recheck the
MICRO UPS Battery Pack
to make sure it is fully
seated and ensure that all
wiring from the MICRO
UPS to ONT is installed
correctly as listed by ONT
specific instructions.
Fig. 1
Fig. 2
Fig. 3
Fig. 4

56 REV 01-03-2023
REV 01-03-2023
WARRANTY STATEMENT
Precision Power warrants that the Product sold by Precision Power, or
by either a distributor or stocking representative authorized by Precision
Power to sell the Product manufactured by Precision Power, are free from
Manufacturing Defects (as defined and as determined below) for a period
of three (3) year from the date of sale, subject to and on the terms and
conditions set forth in this Limited Warranty. This Limited Warranty gives you
specific rights, and you may have other rights, which vary from state to state
or province to province.
Precision Power will offer full product replacement or product credit on any
deemed “Manufacturing Defects”, with respect to the Product or the Product’s
components, during the three (3) year Limited Warranty period, by, at the
customer’s sole option, either (a) replacing, at Precision Power cost and
expense, the Product; or (b) crediting full refund back to the customer the
credit card used for purchase of the Product, provided that (in addition to
any other requirements or provisions of the Limited Warranty), the customer
returns, with all shipping costs pre-paid at Precision Power’s sole expense,
the Product that the customer claims are subject to any Manufacturing
Defects according to Precision Power’s returned merchandise authorization
procedures.
Precision Power is the only party authorized to remedy and correct any
Manufacturing Defects as provide by this Limited Warranty, and this
Limited Warranty does not apply to replacements of the Product or Product
component(s), or any other corrective or remedial action with respect to the
Product or Product component(s), made by any other party.
Definition of “Manufacturing Defects”: “Manufacturing Defects” means
verified problems or defects resulting from the manufacture, materials, or
workmanship of the Product or the Product component(s) by Precision Power
that render(s) the Product or Product component(s) unable to function in a
manner consistent with and according to the specifications provided by and
/ or defined by Precision Power that are applicable to the Product or Product
component(s).
Furthermore, Precision Power specifically reserves the right to (a) determine,
at its sole, absolute discretion, whether a Manufacturing Defect(s) exists;
and (b) decline any claim under this Limited Warranty with respect to Product
that Precision Power cannot verify, at its sole, absolute discretion, was
sold to the Limited Warranty claimant either directly by Precision Power, or
through an authorized Precision Power distributor or stocking representative.
Notwithstanding the foregoing, and without limiting the foregoing,
“Manufacturing Defects” are NOT unconfirmed defects or problems caused
by modifications to, or work performed on, the Product by any party after the
sale of the Product by Precision Power. In addition, “Manufacturing Defects”
are not unconfirmed defects or problems caused by utilization of the Product
in a manner inconsistent with the specifications provided and / or defined by
Precision Power that are applicable to the Product, or in any unreasonable
manner. Precision Power reserves the right to void this Limited Warranty,
and shall not be obligated to make any replacements or credits of the Credit
Amount with respect to the Product in the event that work is performed on the
Product by any party after the sale of the Product by Precision Power, or if the
Product is used in a manner inconsistent with the specifications provided and
/ or defined by Precision Power that are applicable to the Product, or are used
in an unreasonable manner.
EXCEPT AS SET FORTH IN THIS LIMITED WARRANTY, Precision Power
MAKES NO OTHER WARRANTIES, EITHER EXPRESSED OR IMPLIED.
FURTHERMORE, Precision Power SHALL NOT BE LIABLE FOR ANY
DAMAGES (WHETHER CONSEQUENTIAL, INCIDENTAL, OR OTHERWISE)
FOR ANY BREACH OF THIS LIMITED WARRANTY, EXCEPT FOR Precision
Power’s OBLIGATIONS TO REPLACE, OR PROVIDE CREDIT(S) OF THE
CREDIT AMOUNTWITH RESPECT TO, THE PRODUCT, AS ELECTED
BY Precision Power AT Precision Power’s SOLE OPTION, AND AS MORE
PARTICULARLY PROVIDED BY THIS LIMITED WARRANTY, AND SUCH
REPLACEMENTS OR CREDITS, AS THE CASE MAY BE, SHALL BE THE
SOLE REMEDY FOR ANY SUCH BREACH BY Precision Power OF THIS
LIMITED WARRANTY.
The Part Numbers corresponding to the Products covered by this Limited
Warranty are as follows:
PP36L-12U
FOR WARRANTY CLAIM PLEASE CONTACT:
E: [e-mail]
P: 888-619-1651
SYSTEM STATUS
DC
Mute
Battery
Color - Green
Color-Green
Color - Yellow
Color-Red
Receiving AC power load to operate
under normal conditions
Working off Battery
“Flashing”-Audible Alarm Silenced for
24 hrs, “Solid”-Audible Alarm silnced
until manually enabled again.
Service or replace battery, or
battery missing
ALARM SILENCE
COLD START
N.I.R.
Disables Audible Alarm Function. Press and release to
disable audible alarm for 24 hours. Press and hold for
15 seconds to disable audible alarm indefinitely. Press
and hold for another 15 seconds in order to re-enable
audible alarm frunction.
Allows Desktop Pro capability to restart and restore
standby power with new battery or to use reserve
standby power on existing battery when in AC
power outage for extended time.
Network Interface Reset (N.R.I.) - Allows for DC line
power reset of Optical Network Terminal. Press and
hold for 3 seconds to reset/reboot ONT or CPE device.
VISIUAL INDICATORS
CONTROL SWITCHES
VISUAL AND AUDIBLE STATUS/ALARM SIGNALS
STATE VISIUAL
INDICATOR
AUBIBLE
INDICATOR DESCRIPTION
4
3
2
1
5
6
7
NORMAL
ON
Battery
Replace
Battery
Battery
Missing
Low
Battery
Systen Status
Indicator “ON”
DC Indicator
“ON”
Battery
Indicator “ON”
Battery
Indicator “ON”
DC Indicator
Flashes
System Status
Indicator “ON”
1/2 second
indicator every
15 minutes
1/2 second
audible
indicator 4
times per
minute
Operating under normal AC line
power load and conditions
AC line power failure or AC cord
disconnection. Desktop Pro is being
supplied battery power.
Replace faulty or end of life
battery
Operating on AC power line only
without available battery backup
for outage scenario. When
battery is removed from unit,
battery indicator will illuminate
after 15 seconds
Batttery has reached equal to or
less than 45% remaining capacity
on battery discharge
VISIUAL INDICATORS AND CONTROL SWITCHES
CONNECTION POINTS FOR VAC (INPUT)
AND VDC/TELEMERY (OUTPUT)