Unicol VS1000 User manual

Revised 15/11/19
WARNING
Please carefully inspect the product before assembling. If you notice any apparent damage, call your carrier claims agent and
do not continue the installation until it has been reviewed. Please watch for pinch points. Do not put your fingers between
moveable parts. Do not tamper with or disassemble any spring loaded parts. Before installing, make sure that the supporting
surface will support five times the combined load of the solution and the hardware. Never exceed the maximum load
capacity. Please also layout all components to ensure that you have all of the required parts before proceeding (see BOM list
on following page). Use of this product for anything other than its specified use may result in failure or personal injury. This
product is intended for indoor use only. We recommend using a qualified trades person for installation. Use an assistant or
lifting equipment to lift and position products. For support, please call: [phone].
01865 767676
[email protected]
www.unicol.com
*Please check model specific details before installing*
Screen Size: 33 - 70” Guide Weights: 35-60kg
VS1000 STANDS & TROLLEYS
(UNIVERSAL MOUNTS)

01865 767676
[email protected]
www.unicol.com
2Revised 15/11/19
TOOLS REQUIRED
3/16th
INSTALLERS REQUIRED
COMPONENTS
# DESCRIPTION QTY
11500mm Plain Columns 2
2VSS VS1000 Base 1
310cm Castors 3
4Pozimount Non-Tilting Arms 2
5Pozimount Back Plate 1
# DESCRIPTION QTY
6PS2 150mm Centre Mount Adapter 1
7Universal Fixing Kit 1
8Set Screws (Grub Screws) 4
9Alternative VS1000 Bases -
10 Optional VS1000 Accessories -
2
3
4
5
6
1
9 10
17mm

01865 767676
[email protected]
www.unicol.com
3
Revised 15/11/19
STEP 3 [OPTIONAL]
If adding a shelf or locking cabinet, place the
sockets over the columns and push down until
at desired height. Gently tighten grub screws as
you may want to adjust the height of this after
completing the assembly.
STEP 4
Place the column adapter over the top of the two
columns (ensuring the grub screws are on the
same side as the rear of the base). Once threaded
and at the desired height, tighten the two grub
screws to secure into place. Tighten up the base
and accessory grub screws to secure.
STEP 1
Place base upside down on the floor. Locate
castors and push into the four holes until they click
into place.
Please Note; you may require a mallet. If your base
comes with braked wheels, they will already be
bolted into place.
STEP 2
Placing the base upright again and locking the
brakes on the castors, or ensuring the base is
secure, place the two 1500mm column into the
central sockets. Gently tighten the grub screws
located at the rear to secure.

01865 767676
[email protected]
www.unicol.com
4Revised 15/11/19
STEP 7
Line the screen and arms up with the secured back
plate and offer it up at a slight angle - allowing the
top of the arms to hook over the lip of the back
plate.
STEP 8
Gently lower the screen until the arms are securely
hanging on top of the back plate. Adjust the screen
and once happy, tighten the four screws located
on the mount arms to secure the screen to the
mount.
STEP 5
Locate the mounting holes on the back of your
screen. Line the two mounting arms up and using
the tag locks and manufacturer recommended
screws, attach the arms to the back
of the screen.
STEP 6
Line the back plate up with the mount adapter,
as shown above. Fix 4 screws from behind the
mount adapter and into the 4 rivet nuts located on
the back plate. Ensure back plate is secure and
screws are tightened.