Premier technology Sm1000 series User manual

Installation and Operating Instructions

Premier Technologies Smart Media

SM1000 Series Player

Important

Before using the Premier Information On Hold unit,

please read these operating instructions carefully.

Introduction

The SM 1000 is a 100% digital download Smart Media

player used for Information On Hold. Up to six messages

can be stored on the Smart Media flash card for future

playback. Messages are downloaded to the Smart

Media card via the Proprietary Audio MuVer software

from Premier Technologies. Fresh On-Hold messages

can be downloaded free of charge via the internet with

MuVer software and a Smart Media read/writer, or by

simply inserting a new Smart Media card.

Dealer Service

A network of authorized Premier Technologies, dealers

can provide service backed by Premier’s technical

staff. For the name of your local dealer or for technical

assistance from Premier Technologies, contact:

Premier Technologies, Inc.

One Premier Drive • P.O. Box 159

Long Lake, MN 55356 • (952) 475-2317

(800) 466-8642 • FAX (952) 475-3579

Specifications

Sampling Rate: 64 kbps (effective 112 kbps).

Recording Times: 4,16, 32 or 128 minutes

(memory dependent).

Frequency 200 Hz to 3400 Hz

Response: (Full spectrum of telephone

transmission).

Flash Memory: Nonvolitale, unaffected by power

interruptions, no matter how long

the unit is without power.

Power Source: 12V DC adaptor, included.

Cables (included): RCA to RCA and RCA to Mini.

Audio Outputs: 600 Ohm or 8 Ohm (Note: 8 Ohm

output has a 5 watt amplifier).

Tone Control: 600 Ohm and 8 Ohm outputs.

Working Temp: From +5C to +50C

(40F to 122F).

Dimensions: 4.85”H * 6.5”W * 1.4”D.

Weight: 4lbs. (Boxed).

Operating Controls and Indicators

1. Power - LED - indicates power to the

unit and blinks the message number being

played .

2. AC Adaptor Jack - Insert round plug of

12V DC adaptor into power unit.

3. Play Mode Selection - The SM1000 can play

one message continuously or play all

messages in sequence from the inserted

Smart Media card. To change the message

number to be played, press and hold the

“Play Mode” button for the number of blinks

equal to the desired message number. The

SM1000’s power LED will continuously blink

the message number being played after the

button is released. To play in sequence all

stored messages from the Smart Media card,

press and hold the “Play Mode” button for 7

blinks. The message play number is stored in

the Smart Media card, so loss of power will

not change the message being played.

4. Phone Outputs - Insert the cable provided

into the output jack your phone system

requires, either 600 Ohm or 8 Ohm.

5. Output Tone - Controls the tone on the 600

Ohm and 8 Ohm outputs.

6. Output Volume - Controls the output

volume of the unit.

Installation

1. Plug the small-connector end of the AC adaptor into the 12 V DC input jack at the side of the unit. Plug the

larger power supply end of the adaptor into a grounded AC power outlet. The AC power outlet must be one that

remains ON at all times.

2. Connect a cable (provided) from the music on hold part of the telephone system to the 600 Ohm or 8 Ohm

output jack of the unit.

3. Insert Smart Media card with gold side down.

4. Adjust volume and tone controls to the phone system as needed.

5. Select message to be played using the “Play Mode” button.

FCC Information

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference when the equipment is operated in a commercial environment.

The user is cautioned that changes or modifications not expressly approved by Premier Technologies, Inc. could void the user’s authority to operate the equipment.

Warranty

Upon receipt, Premier Technologies, Inc. will repair or replace, as its option, for a period of three years from the date of purchase, any SM1000 that