Premier 106165 User manual

Important: After installation is
completed, remove the aerator. Do
not lose the gasket (1) in the
aerator. Turn on the water supply
and allow both hot and cold water to
run for at least one minute each.
This flushes away any debris that
could cause damage to internal
parts. While the water is running,
check for leaks. Turn off the water
and replace the aerator.
INSTALLATION STEPS: Single-Handle Lavatory Faucet
Shut off water supply at angle stop. Remove
old faucet. Clean sink surface in preparation
for new faucet.
1.
Making the waterline connections:
Thread the nut (1) on supply line onto
outlet of water supply valve (2) and
tighten with wrench. Do not overtighten.
Ensure the gasket (1) is on the bottom
of the new faucet (2). Place the faucet
(2) through the mounting holes in the
sink. From under the sink, slide the channel
washers (3) onto threaded rods (4).
Secure with nuts.
NOTE: Mounting bracket (5) only needs
to be used if installing onto a sink or
countertop less than 3/4". Otherwise,
it can be discarded.
2.
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft, damp cloth
only. DO NOT USE detergents or cleansers as they may harm the protective finish.
Model Number: 106165 / 106166 / 106169 / 106168
INSTALLATION
Place one end of the spring clip (1) onto the
end of the horizontal rod (2). Insert the
horizontal rod (2) through a hole on the
strap (3). Connect the other end of the
spring clip (1) to the horizontal rod (2).
Insert the lift rod (4) into the strap and
tighten the screw (5).
3. 4.
6.
5.
8.
7.
Apply the silicone to the underside of the
flange (2). Insert the pop-up body (1) into
the drain hole from under the sink. Screw the
flange (2) into the pop-up body (1). With
the pivot hole (3) facing toward faucet,
use groove joint pliers to tighten the nut
(4), but do not overtighten. Do not turn the
pop-up while tightening the nut, or
sealant may not seal drain. Clean excess
putty. Apply thread sealant tape to the
top threads of the tailpiece (5) in a
clockwise direction as shown and
tighten by hand.
Install the horizontal rod (2) and the
stopper (3) as shown (4). Tighten the
pivot nut by hand. (1).
Tools:
Adjustable Wrench
Groove Joint Pliers
Pipe Wrench
Screwdriver
Thread Sealant Tape
Basin Wrench
Plumber's Putty
Remove the stopper (1) and the flange
(2). Screw the brass nut (3) all the way
down. Push the plastic washer (4) and
the gasket (5) down. Unscrew the pivot
nut (6) from the pop-up body (7) and
remove the seal washers (8). Take off
the spring clip (9) from the horizontal rod
(10). Remove the tailpiece (11) from the
pop-up body (7).
1
2
1
3
2
4
5
10
9
6
8
7
11
3
4
2
5
1
3
1
2
4
1
3
2
4
5
3
4
2
1
5
1

106165 / 106166 / 106169 / 106168
www.premierfaucet.com, [e-mail]
MODEL NO.106169
159665
7 Mounting Kits
Handle Wrench
8 994666
3033 Bonnet Cap
Aerator
Ceramic Cartridge & Screw
Bonnet Nut
6
5
4
562
579
994721
Handle Screw & Index Plug
Handle Assembly
PART DESCRIPTION
2
1
NO.
994197
994175
PART NO. QTY.
1
1
1
1
1
1
1
Lift Rod & Lift Knob 994599 1
1
124020
Brass Pop-Up
9
10
1
10
9 Brass Pop-Up 124011 1
1
994602
Lift Rod & Lift Knob
1
1
1
1
1
1
1
1
QTY.PART NO.
994163
994197
NO.
1
2
PART DESCRIPTION
Handle Assembly
Handle Screw & Index Plug
994721
579
563
4
5
6
Bonnet Nut
Aerator
Bonnet Cap
3 304
994666
8 Handle Wrench
7 159665
MODEL NO.106168
Mounting Kits
7
1
2
3
4
8
5
11
6
10
9
Ceramic Cartridge & Screw
MODEL NO.106165
159665
7 Mounting Kits
Handle Wrench
8 994666
3033 Bonnet Cap
Aerator
Ceramic Cartridge & Screw
Bonnet Nut
6
5
4
562
579
994721
Handle Screw & Index Plug
Handle Assembly
PART DESCRIPTION
2
1
NO.
994197
994175
PART NO. QTY.
1
1
1
1
1
1
1
1
161
Cap
11
1 1
1
1
1
1
1
1
1
QTY.PART NO.
994163
994197
NO.
1
2
PART DESCRIPTION
Handle Assembly
Handle Screw & Index Plug
994721
579
563
4
5
6
Bonnet Nut
Aerator
Bonnet Cap
3 304
994666
8 Handle Wrench
7 159665
MODEL NO.106166
Mounting Kits
Ceramic Cartridge & Screw
1
163
Cap
11