Premier 120125 User manual

INSTALLATION STEPS: Single-Handle Lavatory Faucet
Shut off water supply at angle stop. Remove
old faucet. Clean sink surface in preparation
for new faucet.
1.
Escutcheon Installation (optional).
Place the escutcheon (1) and the base
plate (2) on the bottom of the new faucet.
Install the faucet assembly through the
holes of the sink. From underneath the
sink, secure the faucet to the sink with
the washer (3) and nut (4) provided.
Flange Installation (optional).
Place the flange (1) on the bottom of the
new faucet. Install the faucet assembly
through the holes of the sink. From
underneath the sink, secure the faucet
to the sink with the washer (2) and nut
(3) provided.
2.
Cleaning:
To maintain and protect the fine luster of all products, clean with a soft, damp cloth
only. DO NOT USE detergents or cleansers as they may harm the protective finish.
Model Number: 120125 / 120122
INSTALLATION
3. 4.
8.
7.Install the horizontal rod (2) and the
stopper (3) as shown (4). Tighten the
pivot nut by hand (1).
Place one end of the spring clip (1) onto
the end of the horizontal rod (2). Insert
the horizontal rod (2) through a hole on
the strap (3). Connect the other end of
the spring clip (1) to the horizontal rod
(2).
Tools:
Adjustable Wrench
Groove Joint Pliers
Pipe Wrench
Screwdriver
Thread Sealant Tape
Basin Wrench
Plumber's Putty
Making the waterline connections:
Thread the nut (1) on supply line onto
outlet of water supply valve (2) and
tighten with wrench. Do not overtighten.
3
4
2
5
1
3
1
2
4
Push lift rod (1) through hole in bottom
of body then reattach lift rod knob (2).
Tighten screw (3).
9.
Remove the stopper (1) and the flange
(2). Screw the brass nut (3) all the way
down. Push the plastic washer (4) and
the gasket (5) down. Unscrew the pivot
nut (6) from the pop-up body (7) and
remove the seal washers (8). Take off the
spring clip (9) from the horizontal rod
(10). Remove the tailpiece (11) from the
pop-up body (7).
5. 6. Apply the silicone to the underside of the
flange (2). Insert the pop-up body (1) into
the drain hole from underneath the sink.
Screw the flange (2) into thepop-up body (1).
With the pivot hole (3) facing toward faucet,
use groove joint pliers to tighten the nut
(4), but do not overtighten. Do not turn the
pop-up while tightening the nut, or sealant
may not seal drain. Clean excess putty.
Apply thread sealant tape to the top
threads of the tailpiece (5) in a clockwise
direction as shown and tighten by hand.
1
2
1
3
2
4
5
10
9
6
8
7
11
1
2
3
1
3
4
2
3
2
1
10. Important: After installation is completed,
remove the aerator. Do not lose the
gasket (1) in the aerator. Turn on the
water supply and allow both hot and cold
water to run for at least one minute
each. This flushes away any debris that
could cause damage to internal parts.
While the water is running, check for
leaks. Turn off the water and replace the
aerator.
2
3
1

120125 / 120122
1
NO.
264
Lift Rod & Lift Knob
124020
Pop-Up Assembly
1
1030723
Handle Assembly
30
10
11
Flange & O-Ring
8
7
9
394
263
Mounting Kit
Escutcheon & Base Plate
1
1
1
1
1
163 Cap
4
6
5
260
994658
551
Bonnet
Cartridge
Aerator
2 307
Screw
1
1
1
1
1
PART NO.PART DESCRIPTION
MODEL NO.120125
QTY.
12
124011
267
266
Pop-Up Assembly
Lift Rod & Lift Knob
Escutcheon & Base Plate
1
1
1
994658
Aerator 552
31
Flange & O-Ring
Bonnet
Cap 17
260
Cartridge
1
1
1
1
1
1
PART NO.PART DESCRIPTIONNO.
Screw
Handle Assembly 1030722
307
MODEL NO.120122
QTY.
1
1
www.premierfaucet.com, [e-mail]
1
10
11
8
7
9
3
4
6
5
2
12
1
3
4
2
5
6
7
8
910
12
11
994666
Handle Wrench 1 994666 Handle Wrench 1
Mounting Kit 394