Prestige APS510Z User manual

2020 Voxx Electronics. All Rights Reserved.
1
2
3
4
1 2 3 4
VOXX
1 Dk. Blue/Black ALT. Ch.3 Output (Start) (-)
2 Orange/White Starter Kill Output N.O. (-)
3 Green/Lt. Blue Ch. 4 AUX Output (-)
4 Purple DoorTriggerInput (+)
5
Dk. Blue TrunkOutput (-)
6 Lt. Green Instant TriggerInput (Hood/Trunk) (-)
7 Lt. Blue/GreenCh. 5 Aux Output (-)
8 Brown DoorTriggerInput (-)
9 Green/White Dome light Output (-)
10 Empty Empty
11 White/Blue Headlight Output (-)
12 Dark Green Sensor Input (-)
13 Yellow IgniƟon Input (+)
14 Black/White Horn Output (-)
14 Pin Input/Output
1 White Parking Light (30)Output
2 Black Ground Input (-)
3 White/Red Parking Light (87)Input
4 Orange Starter Kill Output N.C. (-)
5 White/Black Siren Output (+)
6 Red BaƩery 12VInput (+)
6 Pin Power
1 Blue Data TX
2 White Data RX
3 Black Ground (-)
4 Red BaƩery 12V (+)
CarLink
4 Red BaƩery 12V (+)
3 Blue Data TX
2 Black Ground (-)
1 White Data RX
DBI
4 Red BaƩery 12V (+)
3 Black Data TX
2 Green Warn AwayInput (-)
1 Blue Full TriggerInput (-)
Shock
2 Red BaƩery 12V (+)
1 Blue LED Output (-)
LED
2 Gray Valet Input (-)
1 Black Ground (-)
Valet
3Red/Black 2nd Unlock Output (-)
2 GreenUnlock Output (-)
1 Red Lock Output (-)
Door
Lock
Not Included
Replacement Part #4120473
Replacement Part #4120472
Not Included
Replacement Part #4700033
Replacement Part #4120474
Replacement Part #4120475
85 Red
IgniƟon Input (+)
86 OrangeStarter Kill Input (-)
87ABlack Starter Interrupt - Key Side
30 White/Black Starter Interrupt - Motor Side
Starter Kill
Replacement Part #4360828
86 85
87
87A
30
Replacement Part #4360846
1
2
3 5 7 9 11 13
4 6 8 10 12 14
1
2
3
1
2
3
4
1 3 5
2 4 6
APS510Z
Security System Layout
Replacement Part # 185BP
Shock Sensor
Part #4700033

APS510Z
Security with Keyless Entry
Quick Installaon Guide
1 Chirp 2 Chirp
3 Chirp 4 Chirp 5 Chirp 6 Chirp
1 Lock / Unlock Funcon 500ms 3.5sec 500ms L, DBL UL DBL L, 500ms UL DBL L, DBL UL 500ms L, 350ms UL
2 Ignion Lock OFF ON
3 Ignion Unlock OFF Unlock All Unlock Driver
4 Exterior Illuminaon OFF With Arm With Disarm With Arm & Disarm
5 Auto Relock OFF Auto Lock Auto Lock & Arm
6 Auto Arming OFF Auto Arm Auto Lock & Arm
7 Nocaon Sound Both Siren Horn
8 Horn Timing 16ms 30ms 40ms 50ms 10ms
9 Valet Override Method Valet Custom Code
10 Driver Priority Unlock OFF ON
11 Silent Choice OFF From Transmier OEM Style
12 Park Light / Trunk Swap NA
13 AUX Ch. 4 Pulse Push & Hold 10sec 20sec Latch On/OHold 3/s for O/P
14 AUX Ch. 5 Pulse Push & Hold 10sec 20sec Latch On/OHold 3/s for O/P
15 Alarm Trigger Length 30sec 45sec 60sec 90sec 120sec
16 Dome Light Delay Timer Off/ Program 15sec
30sec 45sec 60sec 120sec
17 Security Prole All On Doors O
Hood/trunk OAll OAll On w/ OEM RS
18 Data Port Protocol ADS DBI
Feature Bank 2
Opons
Features
1 Shock
2 Trunk/Hood
3 Door
The Feature Bank below can also be programmed using the FlashLogic Weblink.
Please visit www.FlashLogic.com for more detail.
Alarm
When the alarm is triggered the system will provide feedback to the
user. Upon disarm, the system will beep four (4) mes and ash the
LED to indicate the Alarm Trigger Zone.
Important Update
The default Data Port Protocol of this system is ADS. If using an FLCAN or other external integraon module be sure to choose iDatalink
2-Way when ashing.
This system will also support DBI. This will require programming Feature Bank 2, Feature 18 to DBI.
Notes
For Complete Installaon Guide and Technical Support
Please Visit
www.voxxuniversity.com
Or Call
1-800-225-6074
REV. B 2020 Voxx Electronics. All Rights Reserved.
Feature Programming
Remote Programming
Dome Delay Programming
Shock Sensor
The APS510Z includes two (2) programmed remotes. If required,
addional remotes can be programmed to the system. Remote
Programming is located in Feature Bank 1. To enter Remote Auto
Programming:
1. Turn the ignion key to ON.
2. Press and release the valet buon three (3) mes. System will chirp
and ash the parking lights one (1) me.
Press the lock buon on each remote. The system will beep one (1)
me to indicate the remote has been programmed. Only primary
remote funcons are auto programmed. This Includes Lock, Unlock, and
Trunk/Start.
If using AUX output control, the remote channel must be manually
programmed to the system AUX output. Please see the complete
installaon guide for manual remote programming instrucon.
The APS510Z Feature Bank can be programmed by using the valet
buon and remote. To enter Feature Bank programming:
1. Turn the ignion key to ON.
2. Press and release the valet buon three (3) mes. System will
chirp and ash lights one (1) me for Feature Bank 1, Remote
Programming.
3. Cycle ignion key OFF/ON. System will chirp and ash lights two (2)
mes for Feature Bank 2.
4. Press valet buon to cycle features. LED will ash to display feature
number.
5. Press lock buon to cycle opons. System will chirp to indicate
opon number.
To exit Programming cycle ignion key OFF and wait ten (10) seconds.
The System will also automacally exit programming aer sixty (60)
seconds of no acvity.
The shock sensor should be mounted to a solid surface in the center of
the vehicle. Once mounted the shock sensor will require adjustment.
To increase sensivity: Turn adjustment dial clockwise.
To decrease sensivity: Turn adjustment dial counter clockwise.
To test sensivity, strike the vehicle with an open palm. Adjust the dial
to provide coverage to as much of the vehicle as possible.
This system can be programmed to ignore the vehicle’s theater dimming
dome light. This feature will be used when connecng the door trigger
input to the dome light circuit for alarm trigger. Note: Vehicle windows
should be open to prevent accidental locking of keys in the vehicle.
Start with all doors closed and the vehicle dome light o.
1. Press Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock. LED will light
solid.
2. Open and close the driver door.
The system will monitor the dome light circuit. When the dome light
turns o the system will set the delay me and add an addional two
(2) seconds.
Dome Delay Reset
1. Key ON/OFF, ON/OFF, ON/OFF.
2. Press and hold valet buon for ve (5) seconds.
The system will chirp one (1) me to indicate reset is complete.
Data Protocol Selecon
The default data port protocol of this model is ADS (iDatalink 2-Way).
This model is capable of detecng the correct data port protocol (ADS
or DBI) and automacally conguring Feature Bank 2; Feature 18. To
inialize the detecon procedure:
1. Press and hold the valet buon.
2. Cycle the vehicle’s Ignion ON/OFF two (2) mes.
3. Release the valet buon.
The system will automacally detect and set the correct data port
protocol, ADS or DBI.
Note: This feature is only available on module rmware v2.00 or higher.
Chirp Delete
System ARM/DISARM chirps can be toggled ON or OFF without
entering the Feature Bank programming.
1. Turn the ignion key ON/OFF.
2. Press and release the valet buon three (3) mes.
The system will respond with one (1) chirp for ON and two (2) Chirps
for OFF. This feature will not aect alarm trigger or programming.
User Programmable LED
System LED nocaons can be turned ON or OFF without entering
Feature Bank programming.
1. Turn the ignion key ON/OFF, ON/OFF.
2. Press and hold valet buon for ve (5) seconds.
The LED will ash one (1) me for ON, two (2) mes for OFF. This
feature will not aect LED ash during programming.