Prestige APS-55C User manual

128-7216
1 of 2
3 Channel Remote
Car Starter
Model APS-55C
Owner’sManual
FEATURES :
!1 Three Button Programmable RF Transmitter
!Three Channel Receiver (capable of accepting 4 transmitters)
!Keyless Entry Outputs (+) and (-)
!On-Board Start Relay
!On-Board Accessory Relay
!On-Board Ignition 1 Relay
!On-Board Ignition 2 Relay
!Ignition 2 Relay Selectable On or Off During Cranking
!On-Board Parking Light Relay
!Ignition 3 / Shock By-Pass / GM VAT Output (relay required)
!Tach Signal Learning Circuit
!Two ( + ) and Two ( - ) Safety Shutdown Circuits
!Alarm By-Pass Output
!AccessoryOutputs
(PulseBefore&AfterStart,DuringCrank&AfterShutDown)
!Selectable Steady or Flashing Parking Lights for Run Indication
!Selectable 5, 10, 15, 20 Minute Run Time
!Selectable 1 Sec., 3.5 Sec., or 1 Sec./Dbl 1 Sec. Door Lock Output Pulse

128-7216
2 of 2
KEYLESS ENTRY 1. The Lock button on the transmitter is used to lock the vehicle's doors,
the Unlock button is used to unlock the vehicle's doors. To lock or unlock
the doors simply press and release the desired function button one time.
As a keyless entry unit, for your convenience, the parking lights will flash
once when the doors are locked and twice when the door are unlocked.
REMOTE CAR FINDER
The Lock or Unlock buttons are also used to access the car finder mode.
This feature is particularly useful in a crowded parking lot where finding
your car may be difficult. To access the car finder mode, while within
range of your car, simply press and hold either the lock or unlock button
of your transmitter for three seconds. The parking lights will begin to
flash making your vehicle more visible. The lights will stop automatically after 30
seconds. If you wish to turn off the car finder mode prior to the expiration of the 30 second
timer, press and release either the lock or unlock button of your transmitter one time
.
REMOTE STARTING THE VEHICLE
This unit will not start the vehicle if any one of the following situations exists;
The vehicle's hood lid is opened.
The gear shift selector is not in Park.
The brake pedal is depressed.
The safety control switch is in the Off position.
1. To start the vehicle, press and release the Key/Option button two times within 2 seconds.
The vehicle will start and remain running for the pre-programmed 5,10,15,20 minute run
cycle. As a visual indication, the parking lights will flash or remain on depending on
the setting by your installation center.
2. When you arrive at the vehicle, turn the ignition key to the ON position (not the spring
loaded start position), then step on the brake pedal to disengage the remote starter. The
vehicle will continue to run, but now on it's own power.
NOTE: The engine will stop running before the pre-programmed run cycle has expired if
you perform any one of the following functions;
-Press and release button 2 on the keychain transmitter two times within 2 seconds.
-Depress the brake pedal.
-Open the vehicle's hood
-Move the safety control switch to the Off position.
SAFETY CONTROL SWITCH
The red handle control switch allows you to temporarily disable the remote starting function
of the system and moving this switch to the Off position is recommended whenever the
vehicle is being serviced. When the system is disabled, the remote door locks and optional
accessories will remain operational.
FUNCTION SETTING CHART
To be completed by installer
Run Time 5 Min "10 Min "15 Min "20 Min "
Door Lock Timer 1 Sec/1 Sec "3.5 "1 Sec/Dbl 1 Sec "
Lights Pulse "Steady "
© 2004 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788 128-7216