Prestige Prestige 128-8613 User manual

128-8613
1 of 12
Page 1
Model APS-620N
Installation Manual
This Remote Start System is designed to be used with
Automatic Transmission- Fuel Injection Vehicles Only!
COMPONENTS:
Control Module
2 Four Button RF Transmitters
Antenna/Receiver
1 1” X 1.75” Foam Pad
6 Pin Main Power Harness
7 PinAccessory Harness
1 Hood Pin Switch
2Pin Door Lock/Unlock Harness
3 Pin Parking Light/Ground Harness
2 Pin LEDAssembly
2 Pin Push-Button Valet/Program Switch
3PinAntennaReceiverHarness
4 PinAuxiliary Output Harness
Installation/OwnersGuide
FEATURES:
Selectable Ignition Lock & Unlock
Selectable Door Lock/Unlock Output Timing
Safe Start (Requires double push of the start button to engage the remote start function)
On Board Parking Light Relay
Trunk Release Output
Horn Chirp Output With Selectable Duration
Selectable RF Start Chirp
Car Finder Mode (Can elect to have horn beep along with parking lights if connected)
Selectable Run Times 5, 10, 15, or 20 Minutes
Selectable Gas or Diesel
Automatic Start Timer (Can be set to start your car automatically at 2 or 4 hour intervals)
4 Negative PulsedAux Outputs Before Start,After Start, During Crank,After Shut Down
(To aid installation in many vehicles with factory alarm systems)
FCC NOTICE
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance voids the
users authority to operate this device.

128-8613
2 of 12
Page 2
INSTALLATION OF THE MAJOR COMPONENTS:
CONTROL MODULE:
Selecta mounting location insidethepassenger compartment(up behindthedashboard).
Themounting locationselected must be within 24" of theignitionswitchwiringharness to
allow connection of the 6 pin main wiring harness.
Be certain that the chosen location will not interfere with proper operation of the vehicle.
Avoid mounting the module to or routing the wiring around the steering shaft/column, as
the module or wiring may wrap around or block the steering wheel preventing proper
control of the vehicle. Secure the module in the chosen location using cable ties or
screws as necessary.
Do Not Mount The Module In The Engine Compartment, as it is not waterproof.
DASH MOUNTED LED:
The small LED included in the kit will serve as a visual indicator of the system’s status
and provide a visual deterrent to a potential thief. The LED also provides important feed
back information during the transmitter and feature program modes. The LED should be
installed in the dash in an area highly visible so that it may be seen from the driver's seat
as well as from outside the vehicle. Inspect behind the chosen location to insure that the
drill will not penetrate any existing factory wiring or fluid lines. Carefully drill a 1/4" hole in
the desired location and pass the connector end of the LED through the hole and toward
the control module. Press the LED firmly into place until it is fully seated in the mounting
hole.
THE RECEIVER/ANTENNAASSEMBLY:
The Superheterodyne ReceiverAntennaAssembly provided with this unit allows routing
frombelowthedash boardfor maximumoperating range. Choosea locationabove thebelt
line(dashboard) ofthevehicle forbestreception. Specialconsiderations mustbemade for
windshieldglassas some newer vehicles utilizeametallicshielded window glass that will
inhibitorrestrictRF reception. In these vehicles, route the antenna toward a rear window
location for best reception. Secure the antenna with double stick tape provided. After
securingtheantennawith tape, we advise also securing a section of the antenna cable to
afixed support. This will prevent theantennafrom dropping down incasethedouble stick
tape is exposed to extreme heat which may loosen it's gummed surface. Route the con-
nector toward the control module using caution not to pinch the cable as this will cause
poor or no RF reception to the control module.
VALET/PROGRAM/MANUAL OVERRIDE SWITCH :
Select a mounting location that is easily accessible to the operator of the vehicle. It is not
necessary to conceal the switch. However, concealment is recommended as it offers a
higherlevelofsecurity. The switch can be mounted to the lower dash panelin the driver's
area. Inspectbehindthechosen location to insure that adequate clearance is allowed for
the body of the switch, and also that the drill will not penetrate any existing factory wiring
or fluid lines. Drill a 9/32" hole in the desired location and mount the switch by passing it
through the panel from the underside. Secure the switch using the nut, star washer.
Route the switch's connector toward the control module.
NOTE: During the program sequence, there are times when this switch and the ignition
switchwillbeused simultaneously. Werecommendthatthepushbutton switchbe mounted
on the left side of the ignition switch to facilitate this operation.
HOOD PIN SWITCH:
The pin switch included in this package are intended for protecting the hood area of the
vehicle. In all cases, the switch must be mounted to a grounded metal surface. When
the pin switch is activated, (hood/trunk open), it will supply a ground to the input wire
activating the alarm. In addition, the hood switch is required for the safety shut down of

128-8613
3 of 12
Page 3
the remote start unit. If the vehicle is being worked on, this hood switch prevents the
remote start activation even if the RF command to start is issued. This switch must be
installed in all applications. Failure to do so may result in personal injury or
property damage.
Mount the switch in the hood locations away from water drain paths. If necessary, a
bracket may be used to move the switch away from rain gutters or allow mounting to the
firewallbehind the hood seal. In both cases the switch mustbe set up to allow the hood to
depress the switch at least 1/4 inch when the hood is closed and fully extended when the
hood is opened. For direct mounting, a 1/4 inch hole must be drilled. Carefully check
behindthe chosen location toinsurethedrill will notpenetrateanyexisting factory wiring or
fluidlines.
Drill a 1/4" hole in the desired location and thread the pin switch into it using a 7/16" nut
driver or deep well socket. If using the mounting bracket, first secure the bracket to the
desiredlocationandsecurethepinswitchinthe pre-threaded mounting bracket hole.
DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT /
OUTPUTHARNESSINTOTHECONTROLMODULE UNTILALLCONNECTIONSTOTHE
VEHICLE HAVE BEEN MADE. AFTER SELECTING YOUR TARGET WIRES AS DE-
FINEDBELOW,DISCONNECTTHE NEGATIVEBATTERYCABLE FROMTHEVEHICLE
BATTERYPRIORTOMAKINGANYCONNECTIONS.
Note: Do not remove the fuse holders from this wire harness.
Fuses must be used and located as close as possible to the power
source for adequate protection of the vehicle.
WIRING THE 6 PIN MAIN POWER HARNESS Connector “C”:
Fused RED w/ WHITE TRACE WIRE: +12 volt Battery1 Source 20A Max
Locate the vehicle battery wire(s) at the ignition switch. Verification: These wires will register
voltage in all positions of the ignition switch. Connect the Red w/White wire to the vehicle's battery
wire. This wire provides power for the control circuit as well as the ignition 1 and ignition 2 relays.
Fused RED WIRE: + 12 Volt Battery 2 Source 20AMax
Locate the vehicle battery wire(s) at the ignition switch. Verification: These wires will register
voltage in all positions of the ignition switch. Connect the Red wire to the vehicle's battery wire.
This wire provides power for the start relay and the accessory relay.

128-8613
4 of 12
Page 4
YELLOW Wire: Starter Output
Careful consideration for the connection of this wire must be made to prevent the
vehicle from starting while in gear. Understanding the difference between a me-
chanical and an electrical Neutral Start Switch will allow you to properly identify
the circuit and select the correct installation method. In addition you will realize
why the connection of the safety wire is required for all mechanical switch con-
figurations.
Failureto makethisconnection properly canresultin personalinjuryand property damage.
In all installations it is the responsibility of the installing technician to test the remote start
unitand ensure that thevehiclecannotstart via RFcontrolin any gearselectionother than
parkorneutral.
Inbothmechanical and electrical neutral startswitchconfigurations,theconnection of the
Yellow wirewillbe madetothe low currentstartsolenoidwire of theignitionswitch harness.
This wire will have +12 volts when the ignition switch is turned to the start (crank) position
only. This wire will have 0 volts in all other ignition switch positions.
BLUE Wire: Ignition 1 Output
Connectthis wiretothe ignition1wire fromtheignition switch. This wirewill show +12volts
when the ignition key is turned to the "ON" or "RUN" and the "START" or CRANK"
positions, and will have 0 volts when the key is turned to the "OFF" and "ACCESSORY"
positions.
GREEN Wire: Ignition2Output
Connect this wire to the ignition 2 wire from the ignition switch. This wire will show + 12
volts when the ignition key is turned to the "ON" or "RUN" position and is some cases the
"START" or CRANK" position. This wire will show 0 volts when the key is turned to the
"OFF" and "ACCESSORY" positions.
NOTE: See programming information (Bank 3 Selection # 6) concerning this wire to allow
outputduring the "START"mode.
VIOLET Wire: Accessory Output
Connect this wire to theAccessory wire from the ignition switch. This wire will show + 12
volts when the ignition switch is turned to the "ACCESSORY" or "ON" and "RUN" posi-
tions, and will show 0 volts when the key is turned to the "OFF" and "START" or "CRANK"
positions.
Wiring The 2 Pin Door Lock/Unlock Harness Connector “B”:
The Red & Green Door Lock/Unlock output wires provide a pulsed ground output to control the
vehicle door lock / unlock circuits. The output of these wires has a maximum switching capability
of 250 mA. Many vehicles today have factory door lock relays which can be connected directly to
these outputs, however always confirm that the factory relays in your particular vehicle do not
exceed the rated 250mA output of the units door lock/unlock circuit. Plug the 2 pin connector of the
door lock/unlock harness into the mating connector shell of the control module. Determine the
door lock circuit of the vehicle you are working on and wire according to the diagrams shown.

128-8613
5 of 12
Page 5
3 Wire Ground Switched Door Lock Circuits:
In this application, the Red wire of the 2 pin harness provides a ground pulse during the arming
sequence, or pulsed ground lock output. Connect the Red wire to the low current ground signal
wire from the factory door lock switch to the factory door lock relay.
The Green wire of the 2 pin harness provides a ground pulse during the disarming sequence, or
pulsed ground unlock output. Connect the Green wire to the low current ground signal wire from
the factory door unlock switch to the factory door unlock relay.
Negative Type Door Lock Circuits

128-8613
6 of 12
Page 6
Wiring The 4 Pin Auxiliary Output Harness, Connector “A”
The auxiliary 4 pin connector provides low current outputs to control various functions in
the vehicle during different stages of the Remote Start unit's operation. Understanding
these outputs and the time in which they occur will allow you to determine if they are
needed for the particular vehicle you are working on as well as how to use them.
Black w Blue Trace Wire: Pulsed Ground Output Before Start
The Black w/ Blue Trace wire will provide a 1 second 250 mA pulsed ground output 1.5
second before the remote start unit activates as well as when the transmitter is used to
disarm the system. Typical use for this output would be to disarm a factory theft deterrent
system to prevent false triggering of the factory alarm when the remote start unit engages
or when the transmitter is used to unlock the doors.

128-8613
7 of 12
Page 7
2 Pin Valet/Program/Override Push-Button Switch, Connector “D”
TheBlack &Grey twinleadwires loadedin thetwopin blueconnector aretheground supply
and program/valet/override input of the Remote Start unit. Route the two wires from the
previously installed Push-Button switch to the mating connector on the control module.
Black w/ Light Green Trace Wire: Pulsed Ground OutputAfter Start
The Black w/ Light Green Trace wire will provide a 1 second 250mA pulsed ground output
after the vehicle is started under control of the remote start unit. Typically this wire will be
used to re-lock the vehicle doors if the doors unlock automatically when the factory anti-
theft system is disarmed.
Black w/ Red Trace Wire: Pulsed Ground OutputAfter Shutdown
TheBlack w/ RedTracewire will providea1 second 250mApulsed ground outputafterthe
remotestartunitshutsdown. This output will occur regardless of whether the circuit times
outor is manually terminated. Typically this output willbeusedto re-lock the vehicledoors
if the doors unlock automatically when the ignition circuit transitions to off.
Black w/ Yellow Trace Wire: Ground Output During Start (Crank)
TheBlack w/YellowTracewire willprovidea 250 mAgroundoutput whilethestarteroutput
of the remote start unit is active. This output can be used to activate the Crank Low/Bulb
Testwire foundinsome GM vehicles. Thiswireis also referredtoas the ECMwakeup wire
insomeChrysler vehicles.
NOTE: The outputs above are low current outputs and must be used with a relay if the
circuit's requirement is more than 250 mA.

128-8613
8 of 12
Page 8
3 Pin Antenna/Receiver, Connector “F”
Routethe 3 pin connectorfromthe previously installed antennareceiverassemble to the
matingconnector on the controlmodule. Thisconnector supplies 5volts,ground and RF
data from the antenna receiver to the remote start module. Be certain this connector is
firmly seated making good contact to the control unit.
2 Pin LED Harness, Connector “G”
Routethetwin lead Red and Blue wires from theLEDtotheremote start control unit and
plug the two pin connector into the mating white mini connector on the control module.
thesewires control the anode and cathode of the dash mounted LED.
3 Pin Parking Light Input/Output & Ground Harness, Connector “H”
Black Wire: Chassis Ground Source
Connectthe Black wiretoa known vehicle groundsource orto a solidcleanmetal part of
the chassis. Be certain to remove any paint or grease and secure this wire with a self
tappingscrewand ring terminal.
White w/ Red Trace Wire: Parking Light Flasher Feed
Thiswireisthecommoncontact of the on board parkinglightflasher relay. If the vehicle
youare working on has +12voltswitched parking lights, connectthiswireto a fused +12
volt source. (Max. 15Amps)
NOTE: If the vehicle's parking lights are ground switched, connect this wire to chassis
ground.
White Wire: Parking Light Flasher Output
Thiswire is thenormallyopen contactof the onboardparkinglight flasher relay. Connect
thiswire to the vehicle parking light feed wire.
7 Pin Accessory Input/Output Harness, Connector “E”
Brown w/ Black Trace Wire: Positive Inhibit Input
TheBrown w/BlackTracewireprovidesan instantshutdownfor theRemoteStartControl
modulewhenever it gets +12volts. Ifthe Brake lights switchinthe vehicle switches +12
voltstothebrake light circuit, connect the Brown w/ Black trace wire to theoutputsideof
the brake switch. This will allow the Remote Start to shut down if an attempt is made to
operatethe vehiclewithoutthekeywhile runningunderthe controloftheRemoteStart. In
mostvehicles,in order to shiftintogear, the brake pedal must be depressed. The brake
input will in turn cause the remote start unit to shut off.
Grey w/ Black Trace Wire: Negative Inhibit Input
TheGreyw/ BlackTracewireprovidesan instant shutdownfor the Remote StartControl
Module whenever it is grounded. Connect the Grey w/ Black trace wire to the hood pin
switch previously installed. This wire must be routed through a grommet in the firewall
and connected to the hood pin switch. If the pin switch is to be used with an alarm
system, connect this wire using a diode assembly.
DONOT RELEASE THISVEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE
OPERATION OF THE HOOD PIN SAFETYSHUT DOWN FEATURE.
IMPORTANT! This connection is a safety wire and must be connected to a hood pin
switchandtested as described. Failure to dosomayresult in personal injury or property
damage. This wire may also be used if the vehicle brake light circuit switches ground to
thebrakelights. An isolation diode must beusedforgroundswitchedbrake light circuits
and must be connected to the output of the brake switch.

128-8613
9 of 12
Page 9
Totest this circuit, whilethevehicle is running under controloftheremote startunit,open
thevehicle’shood. Theremotestart unit shouldshutdown immediately. If not, check the
wiring to the control module and the under hood pin switch.
DONOT RELEASETHEVEHICLE TOTHECONSUMER IF THISCIRCUIT DOES NOT
PERFORMASSPECIFIED.
Green w/ Orange Trace Wire: Tachometer Input Signal
This wire will continually monitor the engine's tach rate while the unit is under power of
the Remote Start module. This wire will be routed to the vehicle ECM tach input or
throughthefirewallintotheengine compartmentandconnecttothenegative side of the
ignitioncoil. ThisRemoteStartunitlearnsthetachrateofthevehicleandinmostcases
will operate properly from one multi coil pack regardless of the number of cylinders.
If the vehicle has a single coil unit for each cylinder, it may be necessary to connect
this wire to more than one cylinder for proper tach reference. See multi coil wiring
detailbelow.
Dark Blue Wire: Delayed 250mA Pulsed Channel 3 Output
TheDarkBluewiresupplies a250mAgroundpulsedoutputwheneverchannelthreeof the
receiveris accessed. Pressing thepre-programmedtransmitter buttonforthree seconds
willaccesschannel two. This is a low currentoutputandmust be connected to a relayto
supply power to the trunk release or the circuit you wish to control. Connect the Dark
Bluewiretoterminal # 86 of a VF45F11 P&B relay or equivalent. Connect terminal # 85
of the relay to a fused + 12 volt source. Connect the common, normally open, and
normally closed contacts of the relay to perform the selected function of channel 3.
Black w/ White Trace Wire : 250 mA Horn Output
Theblack w/ white trace wire is provided to beep the vehicle’shorn. This is a transistor-
ized low current output, and should only be connected to the low current ground output
from the vehicle’s horn switch. If the vehicle uses a + 12 VDC horn switch, then con-
nect the black w/ white trace wire to terminal 86 of theAS 9256 relay ( or an equivalent
30 Amp automotive relay ),and connect relay terminal 85 to a fused
+12 VDC battery source. Connect relay terminal 87to the vehicle’shornswitch output,
and connect relay terminal 30 to a fused + 12 VDC battery source.
Light Blue Wire: Ground Output While Running Under Remote Start Control
This wire provides a 300mA ground output that becomes active 3 seconds before the
Remote Start Unit initializes and remains grounded while running plus an additional 4
seconds after the Remote Start Unit turns off. In all of the applications described
below, a relay will berequired.

128-8613
10 of 12
Page 10
The Light Blue wire can be used to accommodate the following situations:
A. Shock Sensor By Pass:
B. Additional Ignition Output:
C. GM VATS Key Override:
Green w/ White trace Wire: Entry Illumination Ground Output
Thiswire provides a 30 secondgroundoutput(300 mA Max.) whenever theremoteis
used to disarm the alarm or to unlock the doors and provides a continuous pulsed output
wheneverthealarmis triggered. This wire should be connected to an external relay and
wired tothe vehicles interior entry lightingwheneverthe optional Interior Illumination
circuit is desired.
Programming Tach Rate:
NOTE: All applications require that tach be programmed.
The unit will not operate unless tach is programmed. If an attempt is made to start the vehicle via
the remote start without first programming tach, the unit will flash the parking lights 7 times
indicating tach has not been learned and stored. If the tach rate is not properly programmed to
thespecificvehicle,theunitmaynotrealizethatthevehicleisrunningincertaininstancesreengage
the starter motor.
The Remote Start Unit will learn the tach rate of most vehicle's single coil, multiple coil
packs, or single injector. To learn tach:
1. Turn the ignition key to the On position.
2. Press and release the valet/program push button switch 3 times.
3. Immediately turn the ignition key Off.
4. Press and hold the valet/program push button switch, then start the vehicle using the
key.
5. When the unit senses the tach signal, the parking lights will begin to flash.
6. Release the valet/program pushbutton switch. The parking lights will turn on for three
seconds to indicate that the learned tach signal is stored and the unit is out of the tach
learnmode.
NOTE: If the unit fails to learn tach rate due to an improper tachometer connection or a
poor tach source, the parking lights will not flash. To correct this situation, locate and
connect the Green/Orange wire to the proper tach signal, and then repeat the tach learn
routine.
Diagnostics:
Enter Bank 3 and turn on selectable feature # 7 as described in the feature selection and
setting section.
Exitthefeatureselectionmodethen press and hold the pushbutton valet/program switch
abd then turn the ignition switch to on position.
NOTE: Diagnostic mode is a temporary mode. Once you have accessed the diagnostic
mode, the unit will pause for two seconds then begin to flash the last stored shut down
code. This code will be displayed three times in succession, then the unit will automati-
cally exit the diagnostic mode.
Theparking lightswillflash anumberof timesindicatingthe reasonfor thelastremote start
shutdown.Thelightflashindications are as follows:
1 Flash Run timer expired
2 Flashes Low or no tach signal (RPM)
3 Flashes Positive inhibit wire activation
5 Flashes RF shutdown signal received, or manual start trigger wire reactivated.
6 Flashes High tach signal (RPM)
7 Flashes Tach signal has not been learned
8 Flashes Negative inhibit wire activation

128-8613
11 of 12
Page 11
Setting Up The System Programming Features:
Bank1 Transmitter Channels
Start with the system disarmed, turn the ignition switch to the on position then:
1) Press and release the push button valet/program switch 3 times.
SirenChirpsonceand or Lights flash one time indicating the transmitter program mode
successfullyentered.
SeeOwners Manual fortransmitterprogramming.
Turn the ignition switch off then on to access Bank 2 Keyless/Alarm feature selections.
1 Flash when the ignition transitions off, followed by 2 chirps/Light flashes when the key is
turned on indicates that you are in feature selection of bank 2.
Press the pushbutton switch:
1 time to access the first selection as shown below. Use the lock button of the transmit-
ter to change the feature selection or press the pushbutton to advance to the next select-
ablefeature.
Bank2
Feature 1 Chirp/Flash 2 Chirp/Flash 3 Chirp/Flash 4 Chirp/Flash 5 Chirp/Flash 6 Chirps/Flash Default
1stDoor Lock/UL 1S/1S 3.5 S/3.5S 1 S/Dbl 1 S. Dbl 1/1 S Dbl 1/Dbl 1 1S L/350mS ul 1S/1S.
2ndAccyLock AutoLockOn Auto LockOff AutoLockOff
3rdAccy.UL Auto UL On Auto UL Off AutoULOff
4th Horn Chirp 10mS 16mS 30mS 40mS 50mS 16mS
5th Chp Del TX On Off Off
When finished setting the keyless/alarm selectable features, turn the ignition off then on
to advance to Bank 3, Remote Start Selectable Features.
1 Flash when the key transitions off and 3 chirps/light flashes when the key transitions on.
Press the pushbutton switch one time to access the first selection as shown below. Use
the lock button of the transmitter to change the feature selection or press the pushbutton
toadvancetothenextselectable feature.
Bank 3
Feature 1 Chirp/Flash 2 Chirp/Flash 3 Chirp/Flash 4 Chirp/Flash 5 Chirp/Flash 6 Chirps/Flash Default
1 RF Start Chirp Off On On
2 Run Time 5 Min. 10 Min. 15Min. 20 Min. 10 Min
3 Park Lights On Steady Flash Steady
4 Input Check Voltage Tach DBI Tach Tach
5 VoltageLevel > 0.5VB4 Start < 0.5VB4Start > 0.5
6 Ign. 2 Select Off With Crank On With Crank Same As Accy On With Crank
7 Diagnostics Off On Off
8Crank Time 0.8Sec 1.0 Sec 1.5 Sec 2.0 Sec 1.0
9 Gas/Diesel Gas Diesel 10 Diesel 15 Diesel 20 Gas
10 Blk/Blue (Aux O/P) Single Pulse As D/L Pulse Single
11 Time Start 2 Hours 4 Hours 4 Hours

128-8613
12 of 12
Page 12
4PININVEHICLE DATABUSPORT (DBI Port)
The 4 pin port located on the side of this module is for proprietary Audiovox data bus interface
modules. These modules are used to access a variety of features in the vehicle which can be
as simple as door trigger inputs, to more complex door locks outputs, or transponder inter-
faces for remote starting. DO NOT connect anything to this port other than the Audiovox IDB
modules or damage to the Remote Start module will occur. All installation instructions for the
IDB modules will be packaged with the individual component along with the proper 4 pin wiring
harness requires to access the data transmit & receive as well as the proper voltage levels for
the interface.
COMPLETING THE INSTALLATION:
Afteryouhave confirmed the operationof theAudiovox Remote Startunitandtested all the safety
features of the system:
1. Mount the control module up and behind the dash securing it in place with cable ties or
screws. Be certain that the chosen mounting location will not inhibit any of the controls of the
vehicle.
2. Securely harness and tie all wiring up and away from all hot and moving parts that they may
come in contact with under the dash board or in the engine compartment areas.
CAUTION: Particularly avoid the area around the steering shaft and column, as wires can
wrap around these mechanisms and impair the safe operation of the vehicle.
3. Apply the Caution Labels supplied with this kit to a conspicuous area in the engine compart-
ment. Make sure to clean the surface before affixing the label.
4. Check the vehicle's wipers, lights, horn, etc.... to insure proper operation.
5. Replace all panels that were removed during installation, and retest the system.
6. Explain all activated features and safety systems associated with Remote Start Unit installed
to the customer.
8. Place the Remote Start / Valet Control Switch Tag on their respective switches and
point these out to the customer.
©2009AudiovoxElectronicsCorporation,Hauppauge,NY11788
128-8613