Pridiom POS091HX User manual

2020550A6823
OWNER'S MANUAL
AIR CONDITIONER
REMOTE CONTROLLER ILLUSTRATION
Thank you verymuch for purchasingour air conditioner.
Please read thisowner's manual carefullybefore using
your air conditioner.
The design andspecifications are subject to change without
prior notice forproduct improvement. Consultwith the sales
agency or manufacturerfor details.
POS091HX
POS181HX
POS121HX
POS241HX
PWS091HX
PWS241HX
PWS121HX
PWS181HX

1
2
2
5
6
7
7
8
11
12
12
13
Handling the remote controller ...................................
Remote controller specification...................................
Features of remote controller buttons .......................
Indicators on display panel...........................................
AUTO operation............................................................
COOL/HEAT/FAN operation.......................................
DRY operation.... .........................................................
TIMER operation........................................................
SLEEP button function.............................................
RESET and LOCK buttons function............................
DIRECTION/SWING button function.........................
Cautions....................................................................
CONTENTS
Keep the remote controller where its
signals can reach the receiver of the
indoor unit. (a distance of 8m is allowed).
Location of the remote controller.
8m
CAUTIONS
The air conditioner will not operate if curtains, doors or other
materials block the signals from the remote controller to the indoor
unit.
Prevent any liquid from falling into the remote controller. Do not
expose the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains
to prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller. either
move these appliances or consult your local dealer.
The remote controller uses two
alkaline dry batteries (R03/LR03X2)
(1) Slide the cover of the battery
compartment off according to the
arrow direction, then replace the
old batteries with new ones.
(2) Insert the new batteries making
sure that the(+) and (-) of battery
are installed correctly.
(3) Reattach the cover by sliding it
back into position.
NOTE:
Do not use old batteries or different
type batteries or rechargeable
batteries, otherwise it may cause the
remote controller malfunction.
Replacing batteries
.
Handling the remote controller
1
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FANSPEED
TIMERON
ECONOMY
ON/OFF
TIMEROFF
FOLLOW
ME
RESETLOCK
SETTEMPERATURE( F)
SWING
LED
DISPLAY
TURBO
O

2
3
TEMP Button : Push this button to decrease the indoor
oO
temperature setting in 1 F increments to 62 F
NOTE: Heat mode is for cooling & heating models only.
1
TEMP Button : Push this button to increase the indoor
oO
temperature setting in 1 F increments to 86 F.
2
MODE Button: Each time the button is pressed, the operation
mode is selected in the sequence of the following:
3
AUTO COOL
DRY HEAT FAN
Model
Transmission Distance
Lowest Voltage of CPU
Emitting Signal
Rated Voltage
RG51I39/BGCEFU, RG51I39/BGEFU
8m
3.0V(Dry batteries LR03 2)
2.0V
Performance Features
Features of Remote controller buttons
1. Operating Mode: AUTO COOL DRY
HEAT(Cooling only model without) and FAN .
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range:
4. Full function of LCD (Liquid Crystal Display)
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
FOLLOW
ME
RESET LOCK
12
4
5
6
7
3
8
9
10
11
12
13
14
Environment
SET TEMPERATURE( F)
SWING
LED
DISPLAY
TURBO
OO
62 F~ 86 F
O
OO
23 F~140 F
Remote Controller Specification
RESET Button: When you press the recessed RESET button,
all current settings are cancelled and the control will return to
the initial settings.
6
ON/OFF Button: Push this button to start operation, push the
button again to stop operation.
9
AIR DIRECTION Button: Press this button to change the swing
o
angle of the louver. The swing angle of the louver is 6 for
each press. When the louver swing at a certain angle which
would affect the cooling and heating effect of the air conditioner,
it would automatically change the swing direction . No symbol
will appear in the display area when press this button.
FAN SPEED Button: Used to select the Fan Speed in four steps-
AUTO LOW MED or HIGH. Each time the button is pressed,
the fan speed mode is shifted.
8
TIMER ON Button: Press this button to initiate the auto-on time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10h, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-on time
to 0.0.
10
4
5
SWING Button: Push this switch button to activate auto
swing feature of the horizontal louver. Push it again to stop.
LED DISPLAY Button: Press this button to clear the digit
display in the air conditioner, press it again to illuminate (Not
available for the units without LED display window).
7
NOTE: Press and hold and buttons together for 3 seconds
will alternate the temperature display between the C & F scale.

TIMER ON OFF
SET TEMPERATURE
Transmission Indicator
Temp./Timer display
Fan speed display
Mode display
ON/OFF display
This transmission indicator will light
when remote controller transmits
signals to the indoor unit.
Displays the current selected mode.
Including AUTO, COOL, DRY, HEAT
(cooling & heating models only) and
FAN.
O
The temperature setting (from 62 F
O
to 86 F) or timer setting (0~24h) will
be displayed. If FAN mode is
selected, there will be no display.
This indicator will be displayed when
the unit is operating.
Displays the selected fan speed:
AUTO, HIGH, MED and LOW.
Nothing displays when the fan speed
is selected in AUTO speed. When
AUTO or DRY Mode is selected, there
will be no signals displayed.
This display area shows the settings
of the TIMER. That is, if only the
Auto-on time function is set, it will
display TIMER ON. If only the Auto-off
time function is set, it will display
TIMER OFF. If both functions are
set, it will display TIMER ON OFF
which indicates you have chosen both
the Auto-on time and Auto-off time.
LOCK display is displayed when
pushing the LOCK button. Push the
LOCK button to clear display.
4
5
Mode display(FAN mode)
FOLLOW ME display
When pressing FOLLOW ME button
in COOL or HEAT mode, the remote
sensing function is activated and this
indicator displays.
TIMER display
LOCK Indicator
Indicators on display panel
Buttons design mightbe slightly different from theactual
one you purchaseddepending on individualmodels.
All thefunctions described areaccomplished by the indoor
unit. If theindoor unit hasno this feature, there is no
corresponding operation happenedwhen press therelative
button on theremote controller.
Note:
TIMER OFF Button: Press this button to initiate the auto-off time
sequence. Each press will increase the auto-timed setting in 30
minutes increments. When the setting time displays 10h, each
press will increase the auto-timed setting 60 minutes increments.
To cancel the auto-timed program, simply adjust the auto-off time
to 0.0
12
LOCK Button: When you press the recessed LOCK button, all
current settings are locked in and the remote controller does not
accept any operation except that of the LOCK. Press again to
cancel the LOCK mode.
13
TURBO Button: Push this button on COOL mode, the air con-
ditioner goes into powerful cooling operation. Push again to
cancel the TURBO function(Not availabe for the air conditioner
without TURBO function).
14
SLEEP Button: Press this button to go into the Energy-Saving
operation mode. Press it again to cancel. This function is only
can be used on COOL, HEAT and AUTO mode and maintain the
most comfortable temperature for you.
11
NOTE: While the unit is running under SLEEP operation
mode, it would be canceled if you press the MODE,FAN
SPEED or ON/OFF button.

Ensure the unit is plugged in and power
is available. The OPERATION indicator
on the display window of the indoor unit
illuminates.
1. Use the MODE button to select AUTO.
2. Push the TEMP button to set the
desired temperature within a range of
OO
62 F ~ 86 F.
3. Push the ON/OFF button to start the
air conditioner. The FAN SPEED is
automatically set and there are no fan
speed indicators shown on the display
panel of the remote controller.
4. Push the ON/OFF button again to stop
the unit operation.
When you set the air conditioner in AUTO
mode, it will automatically select cooling,
heating (Cooling & Heating models only),
or fan only operation depending on what
temperature you have selected and the
room temperature.
Once you select the operating mode,
the operating conditions are saved in
the unit's microcomputer memory.
Thereafter, the air conditioner will start
operating under the same conditions
when you simply push the ON/OFF
button of the remote controller.
2
1
3
Ensure unit is plugged and power is available.
1. Press the MODE button to select COOL,
HEAT (Cooling & Heating models only), or
FAN mode.
2. Push the TEMP button to set the
desired temperature within a range of
OO
62 F ~ 86 F.
3. Push the FAN SPEED to select the FAN
mode of AUTO, HIGH,MED or LOW.
4. Press the ON/OFF button to start the air
conditioner. The OPERATION indicator
on the display panel of the indoor unit
illuminates. Push the ON/OFF button
again to stop this unit operation.
Ensure unit is plugged and power is available.
The OPERATION indicator on the display
panel of the indoor unit starts flashing.
1. Push the MODE button to select DRY.
2. Push the TEMP button to set the
desired temperature within a range of
OO
62 F ~ 86 F.
3. Push the ON/OFF button, the OPERATION
lamp lights and the air conditioner starts
to operate in DRY mode at LOW fan
speed. Push the ON/OFF button again to
stop this unit operation.
Note: The fan speed cannot be adjusted
when the unit is in AUTO and DRY mode.
6
7
3
2
1
4
2
1
3
Auto operation COOL/HEAT/FAN operation
DRY operation
1. In the AUTO mode, the air conditioner
can logically choose the mode of COOL,
FAN and HEAT by sensing the difference
between the actual ambient room
temperature and the set temperature on the
remote controller.
2.If the AUTO mode is not comfortable for you,
the desired mode can be selected manually.
NOTE
The FAN mode can not be used to
control the temperature. While in this
mode, only steps 1 3 and 4 may be
performed.
NOTE
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
FOLLOW
ME
RESET LOCK
SET TEMPERATURE( F)
SWING
LED
DISPLAY
TURBO
O
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
FOLLOW
M E
RESET LOCK
SET TEMPERATURE( F)
SWING
LED
DISPLAY
TURBO
O
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
FOLLOW
ME
RESET LOCK
SET TEMPERATURE( F)
SWING
LED
DISPLAY
TURBO
O

To press the TIMER ON button can set the auto-on
time of the unit. To press the TIMER OFF button
can set the auto-off time of the unit.
1. Press the TIMER ON button. The remote
controller shows TIMER ON, the last Auto-on
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to
reset the Auto-on time to START the operation.
2. Push the TIMER ON button again to set desired
Auto-on time. Each time you press the button,
the time increases by half an hour between 0
and 10 hours and by one hour between 10 and
24 hours.
3. After setting the TIMER ON ,there will be a one-
half second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.
To set the Auto-on time.
To set the Auto-off time.
1. Press the TIMER OFF button. The remote
controller shows TIMER OFF, the lastAuto-off
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to
reset the Auto-off time to START the operation.
2. Push the TIMER OFF button again to set desired
Auto-off time. Each time you press the button,
the time increases by half an hour between 0
and 10 hours and by one hour between 10 and
24 hours.
3. After setting the TIMER OFF ,there will be a one-
half second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.
The effective operation time set by the remote controller for the timer
function is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0,
3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13,
14, 15,16,17, 18, 19, 20, 21, 22, 23 and 24.
CAUTION
!
Example of timer setting
TIMER ON
Start
Off
6 hours later
(Auto-on Operation)
The TIMER ON feature is useful
when you want the unit to turn on
automatically when you return home.
The air conditioner will automatically
start operating at the set time.
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the
last setting of starting operation
time and the signal "h" will show
on the display area.
2. Press the TIMER ON button to
display "6.0h" on the TIMER ON
display of the remote controller.
3. Wait for about 3 seconds and the
digital display area will show the
temperature again. Now this
function is activated.
TIMER ON
Example:
h
Set
8
9
1
1
TIMER operation
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
FOLLOW
ME
RESET LOCK
SET TEMPERATURE( F)
SWING
LED
DISPLAY
TURBO
O
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
FOLLOW
ME
RESET LOCK
SET TEMPERATURE( F)
SWING
LED
DISPLAY
TURBO
O

11
10
TIMER OFF
Stop
On
Set 10 hours later
(Auto-off Operation)
The TIMER OFF feature is useful when
you want the unit to turn off automatically
after you go to bed. The air conditioner
will stop automatically at the set time.
To stop the air conditioner in 10 hours.
1. Press the TIMER OFF button, the last
setting of stopping operation time and
the signal "h" will show on the display
area.
2. Press the TIMER OFF button to display
"10h" on the TIMER OFF display of
the remote controller.
3. Wait for about 3 seconds and the digital
display area will show the temperature
again. Now this function is activated.
TIMER OFF
Example:
h
TIMER ON OFF
h
On
Stop
2 hours later
after setting
Set To stop the air conditioner 2 hours after
setting and start it again 10 hours after
setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to
display 2.0h on the TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to
display 10h on the TIMER ON display .
5. Wait for the remote control to display
the setting temperature.
TIMER OFF TIMER ON
(On Stop Start operation)
This feature is useful when you want to
stop the air conditioner after you go to bed,
and start it again in the morning when you
wake up or when you return home.
Example:
COMBINED TIMER
(Setting both ON and OFF timers
simultaneously)
Start
Example:
TIMER ON TIMER OFF
(Off Start Stop operation)
This feature is useful when you want to start
the air conditioner before you wake up and
stop it after you leave the house.
To start the air conditioner 2 hours after
setting, and stop it 5 hours after setting.
1. Press the TIMER ON button.
2. Press the TIMER ON button again to
display 2.0h on the TIMER ON display.
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to
display 5.0h on the TIMER OFF display .
5. Wait for the remote control to display
the setting temperature.
Off Stop
Start
10 hours later
after setting
TIMER ON OFF
h
2 hours later
after setting
5 hours later
after setting
Set
The timer setting(TIMER ON or TIMER OFF) that in sequence occurs
directly after the set time will be activated first.
If the same time is set for both TIMER ON and TIMER OFF settings, no
timer operation is performed. The air conditioner may stop operating,
either immediately or after approximately 10 minutes.
CAUTION
!
1
The ECONOMY function enables the
unit to automatically increase(cooling) or
O
decrease(heating) 2 F per hour for the
first two hours, then hold steady for the
next 5 hours, after that the unit will stop
operation. It can maintain the most
comfortable temperature and save
energy.
NOTE: The SLEEP function is only
available under Cooling, Heating and
AUTO operations.
ECONOMY button function
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
FOLLOW
M E
RESET LOCK
SET TEMPERATURE( F)
SWING
LED
DISPLAY
TURBO
O

1
1. When you press the recessed LOCK button,
all current settings are locked in and remote
controller does not accept any operation
except that of the LOCK.
Use the LOCK mode when you want to pre-
vent settings from being changed accidentally.
Press the LOCK button again when you want
to cancel the LOCK mode.
A lock symbol will appear on the bottom right
hand side of the remote controller display
when the LOCK function is activated.
2. When you press the recessed RESET button,
all current settings are cancelled and return
to original factory settings.
2
Use the SWING button to activate AUTO
swing function and lock louver in desired
position.
1. When press this button once and quickly,
the air flow direction setting feature of
the louver is activated. The swing
o
angle of the louver is 6 for each press.
Keep pressing the SWING button to
move the louver to the desired position.
2. When press the button without releasing
for 2 more seconds, the auto swing
feature is activated. The horizontal louver
would swing automatically. Press it again
to stop.
NOTE: When the louver swing or move to
a position which would affect the
cooling or heating effect of the air
conditioner, it would automatically
change the swinging/moving
direction(upward or downward).
1
12
13
Cautions
1. When replacing batteries, do not use old batteries or different type
batteries. Otherwise it may cause the remote controller to malfunction.
2. If you do not use the remote controller for a few weeks or more, remove
the batteries. Otherwise, battery leakage may damage the remote
controller.
3. The average battery life during normal use is approximately half a year.
Replace the batteries when there is no receiving beep from the indoor
unit or if the transmission indicator on the remote controller fails to light.
4. Be sure there are no barriers between the remote controller and the receiver
of indoor unit otherwise the air conditioner will not work.
5. Keep the Remote Controller away from all liquids.
6. Protect the Remote Controller from high temperatures and exposure to
radiation.
7. Keep the indoor receiver out of direct sunlight or the Air Conditioner may
malfunction.
8. Keep controller away from EMI (Electro-Magnetic Interference) supplied by
other household appliances.
RESET and LOCK buttons funciton
SWING button function
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
FOLLOW
M E
RESET LOCK
SET TEMPERATURE( F)
SWING
LED
DISPLAY
TURBO
O
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
FOLLOW
ME
RESET LOCK
SET TEMPERATURE( F)
SWING
LED
DISPLAY
TURBO
O