PrimaNOVA GI-D4 User manual

2
Congratulations!
IMPORTANT:READ THIS BEFORE YOU INSERT BATTERIES INTO
THE UNITS!
Both units are furnished with a sophisticated battery charging and back-
up system that allows you to use rechargeable or alkaline batteries.
However, the type of battery used must be set using the A6 and B8 swit-
ches in the battery compartment.
If you set the switch incorrectly, battery leakage may occur, or worse, in
rare cases the battery might explode!
When using alkaline batteries the switch MUST be set to the NON CHA
(no charge) position, i.e. in the down position!
When using rechargeable batteries the switch MUST be set in the CHA
(charge) position, i.e. the up position.
For safety reasons the switch is factory set to the NON CHA position.
Recommendation:
Use the rechargeable batteries that are provided in the parent unit and
set the switch to CHA. If alkaline batteries are used in the baby unit set
the switch to the NON CHA position. Adapters are used as needed.
Legend
We congratulate you on your choice of PrimaNOVA Digital Babycall, model
GI-D4. This product features digital technology and practical safety functions
that ensure you the units are within range. Only non-toxic materials have been
used, and there are no detachable parts that could be swallowed. Bear in mind
that an electronic baby monitor is not a replacement for parental attention and
care; it's a practical aid that makes your day safer.
Please read this manual carefully and keep it in a handy place. If any problems
should arise, use the troubleshooting guide.
Baby Unit
A1 On/Off button ...................... turns the power on or off
A2 Status indicator ................... indicator lamp:
green colour .............. connection OK
red colour .................. sound is transmitted
blinking ...................... weak batteries
A3 Adjustable sensitivity .......... adjustment of sensitivity for sounds from
the baby
A4 Channel selector 1/2/3/4 ..... select the channel with the least noise
(same as the parent unit)
A5 Adapter contact .................. for connecting the adapter cord
A6 Switch for selecting battery type..... Important: read the text box above
A7 Belt clip................................ clip for fastening the unit
A8 Belt clip lock........................ tilt the belt clip up and push it down
A9 Battery door......................... loosen the screw and push down the plastic
tab to insert batteries

3
Parent Unit
B1 On/Off button.................. turns the power on or off
B2 System indicator.............. indicator lamp:
green colour............ connection OK
blinking green (+ alarm tone 1)... weak batteries
blinking red (+alarm tone 2) ...... out of range
B3 Volume control ................ for adjusting volume
B4 Channel selector 1/2/3/4.. select the channel with the least noise
(same as the baby unit)
B5 Adapter contact .............. for connecting the adapter cord
B6 Visual sound indicator..... lights to indicate sound
B7 Switch for range alarm.... the alarm is activated when the switch is in the
up position
B8 Switch for selecting battery type.........Important: read the text box above
B9 Belt clip .......................... clip for fastening the unit
B10 Belt clip lock.................... tilt the belt clip up and push it down
B11 Battery door .................... loosen screw and push down the plastic tab to
insert batteries
• Plug the adapters into a wall socket and put the adapter cord plug into the
baby unit (A5) and the parent unit (B5).
• Turn the units on by pressing A1 and B1. The indicators A2 and B2 light green
to indicate that the units are ready to use. The baby unit lights red when
transmitting sound.
PrimaNOVA uses four AAA batteries, either rechargeable or alkaline.
• Remove the belt clip by tilting the lock (A8 and B10) out while pushing the belt
clip down. Loosen the screw and push down the plastic tab (A9 and B11).
• IMPORTANT: Check that the switch on the left in the battery compartment
(A6 and B8) is in the correct position for alkaline or rechargeable batteries.
Read the text box above.
• Place four AAA batteries in the battery compartment correctly following the
+ and - markings.
• Replace the battery cover and lock the belt clip.
NOTE: If the switch on the left in the battery compartment is in the NON CHA
position with rechargeable batteries, the unit may signal that the bat-
teries are weak even if they are fully charged. If the unit is to be main-
ly used with the adapter, we recommend using alkaline batteries, as
these may be combined with continuous use of the adapter, and will
serve as battery backup in the case of power failure. If you would like
to use rechargeable batteries in both units, additional batteries may be
obtained from the dealer.
Using adapters
Using batteries

4
PrimaNOVA has an integrated charge function in both units. Set the switch on
the left in the battery compartment to CHA (the up position) and insert the
rechargeable batteries correctly following the + and - markings. Plug in the
adapters. The batteries should be charged for about 12 hours. The unit can be
used during charging, but the time for charging should then be at least 14 hours
for a full battery charge. Unplug the adapters after charging.
If the rechargeable batteries appear to be weak (do not hold their power for
long), they must be replaced with new ones (Ni-MH, AAA, 1.2V, 550mAh).
IMPORTANT
NEVER try to charge non-rechargeable batteries as this may be
dangerous.
Batteries should not be charged for more than 24 hours.
Remove the batteries from the units if they are not going to be used for
an extended period of time.
• Press the on/off button (A1) on the baby unit and set the sensitivity level (A3)
to approximately the middle position. The status indicator (A2) changes its
colour when the unit is activated by sound being transmitted to the parent
unit. Select the same channel using the channel selector (A4 and B4).
• Place the baby unit vertically facing the baby and outside the baby's reach.
• Place the parent unit some distance away from the baby unit and press the
on/off button (B1).
• Adjust the volume (B3) on the parent unit to the desired sound level. When
the unit is receiving sound the visual sound indicator (B6) lights for the vari-
able sound level. See the legend for description of light signals and alarm
tones.
NOTE: If the baby unit sensitivity level is set to minimum, only very strong
sounds will be transmitted. If it is set to maximum, even weak sounds
will be transmitted continuously.
The parent unit signals by means of different alarm tones to indicate
range and weak batteries. The alarm tone for range is activated when
the switch B7 is placed in the up position.
IMPORTANT
Check sound transmission before using the units. Check that the units are pla-
ced within range of another and that sound from the baby unit can be heard in
the parent unit. Only a limited number of channels (frequencies) have been
allocated to electronic baby monitors by the authorities. Therefore there may
be interference from other units at the same time that your baby unit is trans-
mitting sound to your parent unit. In such cases try to change the channel and
adjust the sensitivity lower to avoid having your baby unit transmit weak
sounds, such as when your baby moves in its sleep. Another baby monitor can-
not, however, interfere when your baby unit is not transmitting sound, unless it
is on the same channel. Then you simply switch to another channel.
Battery charging
Detailed user instructions

5
Bear in mind that radio signals may be blocked in areas where there is radio
noise. In such situations sounds from the baby unit might not be heard at times,
even though nothing is wrong with the units. This may also occur if another
baby unit is placed between your units or close to your parent unit. The range
will also be substantially reduced when your batteries are weak.
Clean the units using a soft and moist cloth. Never immerse the units in water.
The units must never be subjected to extreme temperatures nor be left in direct
sunlight for extended periods of time. Avoid placing the units in humid rooms
or close to heat sources such as panel heaters.
If the units get wet, turn them off immediately and remove the batteries. Do not
use them until they are completely dry.
If the units emit smoke or a smell, turn them off and immediately remove the
batteries.
Do not try to make technical adjustments or changes by opening the units.
The warranty is voided if the units have been opened. The warranty does not
include the batteries because their life span depends on the way they are used.
If you wish to complain about the product, a copy of the purchase receipt must
be attached together with a detailed description of the problem. By sending a
complete description of what is wrong you will be ensured that your baby moni-
tor is defect-free and you will be just as satisfied with NOVA quality products
as thousands of others throughout Europe.
Maintenance
Warranty
TROUBLESHOOTING GUIDE
Problem
The light indicator (A2, B2) does
not light up.
High screeching sound in the
parent unit.
No sound in the parent unit.
Possible cause
The unit has not been turned on.
The batteries are not properly
inserted.
The batteries are discharged.
The adapter is connected to a
power outlet that does not work.
The units are placed too close to
each other.
The volume is turned up too high.
The volume has been turned
down.
The sensitivity setting on the baby
unit has been set to minimum.
Solution
Press the ON/OFF button (A1, B1).
Check that they have been placed
correctly according to the + and –
markings.
Recharge the batteries while the unit
is turned off.
If the power outlet has a switch, the
switch must be in the on position.
Increase the distance between the
units.
Adjust the volume by turning it down.
Adjust the volume up.
Adjust sensitivity up.
▼

6
Problem
Interference during transmission.
The parent unit indicates that it is
out of range.
Short range
The batteries have not recharged.
The unit indicates low battery
power even though the batteries
are fully charged.
It takes some seconds after the
baby cries until you hear a sound
in the parent unit.
Solution
Switch to another channel and lower
sensitivity.
Reduce the distance.
Place both units vertically and move
them a bit.
There is nothing much that can be
done about local conditions. You might
try turning off light dimmers or other
sources of electronic noise in the
house.
The units rarely have defects.
Turn on the baby unit.
Set both units to the same channel.
Check the batteries.
Take the unit into a place with room
temperature.
Move the units. Try changing channels
and use both units with the adapter.
Charge the batteries for at least 12
hours. Reduce the distance. Local
conditions may reduce the range
dramatically. Reinforced concrete
and house trailers etc. can give
difficult conditions.
Check the batteries. Use both units
with adapters.
Other baby units near by may reduce
the range drastically. Change chan-
nels and move the baby unit and/or
the parent unit.
Put the switch on CHA (up) in the unit
with rechargeable batteries.
Charge the batteries for 24 hours with
the unit off.
Buy new batteries from the dealer.
Put the switch on CHA (up) if the unit
has rechargeable batteries.
Check the batteries in the other unit. If
they work in that unit, contact the dea
ler.
Possible cause
Another baby unit is close by.
Too great a distance between the
units.
Local conditions.
The baby unit has not been turned
on.
The units are set to different
channels.
The baby unit batteries are
discharged or low.
The baby unit is too cold.
The range is too great.
Batteries poor or dead.
Local conditions.
The A6 or B8 switches are set the
wrong way.
The batteries have gone totally flat.
The batteries are very low or defect.
The A6 or B8 switch is set the
wrong way.
Possible defective batteries.
Transmission frequencies: 40.665 MHz / 40.695 MHz
Operating conditions: Up to 300 meters in open air, depending on local
conditions
+5
O
C to +40
O
C. Storage temperature: -20
O
C to
+40
O
C
Power supply: 2 x 6V 200mA AC/DC adapters or 4 AAA batteries
Operating current: DC 6V volts
Content 1 x baby unit
1 x parent unit
2 x AC/DC 6V 200mA adapters
4 x rechargeable NiMH AAA 1.2V environmentally
friendly batteries
This is normal. Your parent unit needs some time to check that the
proper baby unit is trying to make contact. If the delay is 4-6 seconds,
there may be other baby units close by.
Technical specifications
▼