Primex OneVue Classic Series User manual

Classic Series Digital Clock/Timer Install Guide
OneVue Managed Time (Classic Series Models)
OneVue is a trademark of Primex. OneVue is an intelligent environmental monitoring and managed time solution. All other trademarks are the property of their respective owners.
Copyright ©2018 Primex. The Primex logo is a registered trademark of Primex. All Rights Reserved. 4/30/2018
Primex, Inc. | 965 Wells Street |Lake Geneva, WI 53147 | Phone:[phone] | www.primexinc.com

Legal Notice
Copyright ©2018 Primex. All rights reserved.
Printed in the USA.
Information in this document is subject to change without notice. The software described in this document is
furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in
accordance with the terms of those agreements. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic, mechanical or otherwise, for any
purpose, without the prior written permission of Primex.
About Primex
Primex is a leading provider of solutions that automate and maintain facility compliance, increase efficiencies,
enhance safety and reduce risk for enterprise organizations in the healthcare, retail pharmacy, education,
manufacturing and business vertical markets.
The solutions delivered by Primex include Environmental Monitoring, Managed Time and School Bell
Scheduling.
Worldwide Headquarters
965 Wells Street, Lake Geneva, WI 53147
Phone: [phone] | email:[e-mail] | www.primexinc.com

About this Guide
Audience
This guide is intended for users tasked with installing Digital Clocks/Timers for use with the Primex OneVue Managed Time (Classic
Series Models)solution.
Content messaging
This guide includes notes, cautions, and warnings content that highlights important messages.
Typeface Indicates
Note Indicates something important or useful.
Caution Indicates a command or procedure may have an unwanted or undesirable result.
Warning Indicates a command or procedure that could be dangerous to system or device.
Example Provides an example of the topic.
3Classic Series Digital Clock/Timer Install Guide

CONTENTS
Specifications - Classic Series 9
Dimension Specifications 10
Digital code blue and elapsed timer operation 12
Digital Clock/Timer Install - Classic Series 13
Install Requirements 14
Tilt Bracket and Wall Mount Dimensions - Classic Series 15
Tilt Bracket Digital Clock/Timer Install - Classic Series 16
Wall Mount Digital Clock/Timer Install - Classic Series 18
Flush Mount Digital Clock/Timer Install - Classic Series 19
Dual Sided Digital Clock/Timer Install - Classic Series 24
Timer Control Switch Install 26
Remove Digtial Clock/Timer from Tilt Bracket 28
Remove from Dual-Mount Bracket 29
Manual Check-In 30
Warranty 31
Technical Support 32

Important Safety Instructions
READ ALL INSTRUCTIONS BEFORE INSTALLATION, OPERATION, OR MAINTENANCE OF PRODUCT.
Some of the following information may not apply to your particular product model; however, as with any electronic product,
precautions should be observed during installation, operation, and maintenance.
lInstallation must conform to state or local building codes and ordinances.
lInstallation or maintenance should be performed only by qualified personnel as defined in the Local Electrical Code.
lMount in location where device will not readily be subject to tampering.
lAny wiring instructions must be followed precisely. Failure to do so could cause permanent equipment damage.
lTo avoid possible electric shock or damage to the device, disconnect power source before installation or servicing.
lDo not install or use device near water. To reduce the risk of electrical shock, do not expose device to rain or moisture. Device
must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, must be placed on the device.
lDevice is designed for indoor use only. Operating outdoors, or in wet areas, is an electrical hazard and may damage the
equipment while nullifying the warranty.
lDevice is cleanable with a cloth moistened with water or a common disinfectant. Be sure to test any cleaning solutions on a small
area of the clock before using it on the entire device.
lFor healthcare facilities, devices are not intended for patient use and must not be installed within 6 feet (2 m) of patient contact.
AC-Power Models
lAC main power supply must be disconnected while installing or performing maintenance of any device. To completely disconnect
the power input, the main plug should be disconnected from the main socket outlet completely.
lThe main socket outlet must provide a protective earthing connection where the outlet has a protective earth (ground)
connection.
lMain plug is used as disconnect device and it should remain readily operable during intended use.
lIf power cable is connected directly to junction box without an outlet, AC power must be supplied from a circuit that has a
resettable circuit breaker. AC mains power supply must be disconnected while installing or performing maintenance of any
device. Open the circuit breaker supplying the device before attempting installation, maintenance, or repairs.
5Classic Series Digital Clock/Timer Install Guide

Regulatory Approvals
FCC Compliance
Pursuant to FCC 15.21 of the FCC rules, changes not expressly approved by Primex might cause harmful interference and void the FCC
authorization to operate this product.
FCC Radio Frequency Interference
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be
co-located or operating in conjunction with any other antenna or transmitter.
FCC warning
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
lReorient or relocate the receiving antenna.
lIncrease the separation between the equipment and receiver.
lConnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
lConsult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the radiator & your body.
Channel
The Wireless Channel sets the radio frequency used for communication.
lAccess Points use a fixed Channel. You can select the Channel used. This allows you to choose a Channel which provides the least
interference and best performance. In the USA and Canada, 11 channel are available. If using multiple Access Points, it is better if
adjacent Access Points use different Channels to reduce interference.
lIn "Infrastructure" mode, Wireless Stations normally scan all Channels, looking for an Access Point. If more than one Access Point
can be used, the one with the strongest signal is used. (This can only happen within an ESS).
lIs using "Ad-hoc" mode (No Access Point), all Wireless stations should be set to use the same Channel. However, most Wireless
stations will still scan all Channels to see if there is an existing "Ad-hoc" group they can join.
6

Note: This equipment marketed in the USA is restricted by firmware to only operation on 2.4G channel 1-11
7Classic Series Digital Clock/Timer Install Guide

European Union Decl aration of Conformity and Restrictions
Hereby, Primex Inc. declares that this equipment complies with the essential requirements and other relevant provisions of Directive
1999/5/EC:
The Primex Synchronous Network System LED Clocks including the 5.7cm x 4-digit red wall mount (SNS7C200, SNS7G200, SNS7E200-1,
SNS7K200-1, SNS7C212, SNS7G212, SNS7E212-1, SNS7K212-1), 5.7cm x 4-digit green wall mount (SNS7C200G, SNS7G200G, SNS7E200G-
1, SNS7K200G-1, SNS7C212G, SNS7G212G, SNS7E212G-1, SNS7K212G-1), 5.7cm x 6-digit red wall mount (SNS7C202, SNS7G202,
SNS7E202-1, SNS7K202-1, SNS7C419, SNS7G419, SNS7E419-1, SNS7K419-1, SNS7C202E, SNS7G202E, SNS7E202E-1, SNS7K202E-1,
SNS7C419E, SNS7G419E, SNS7E419E-1, SNS7K419E-1, SNS7C202C, SNS7G202C, SNS7E202C-1, SNS7K202C-1, SNS7C419C, SNS7G419C,
SNS7E419C-1, SNS7K419C-1), 5.7cm x 6-digit red flush mount (SNS7E202F-1, SNS7K202F-1, SNS7E202EF-1, SNS7K202EF-1,
SNS7E202CF-1, SNS7K202CF-1), 10cm x 4-digit red wall mount(SNS7C201, SNS7G201,SNS7E201-1, SNS7K201-1), and 10cm x 6-digit red
wall mount (SNS7C203, SNS7G203,SNS7E203-1, SNS7K203-1)
This equipment is marked with and can be used throughout the European community.
This indicated compliance with the R&TTE Directive 1999/5/EC and meets the relevant parts of following technical specifications:
lEN 300 328 – Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission Systems; Data
transmission equipment operating in the 2.4GHz ISM band and using spread spectrum modulation techniques; Harmonized EN
covering essential requirements under article 3.2 of the R&TTE directive.
lEN 301 489-17 – Electromagnetic Compatibility and Radio Spectrum Matters (ERM); Electromagnetic Compatibility (EMC)
standard for radio equipment and services; Part 17 Specific Conditions for Wideband Data and HIPERLAN Equipment.
lEN 60950 – Low Voltage Directive (Safety)
lEN 50385 – Product standard to demonstrate the compliances of radio base stations and fixed terminal stations for wireless
telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency
electromagnetic fields.
Marking by the symbol indicates that usage restrictions apply.
lIndoor use: maximum power (EIRP*) of 100 mW for the entire 2400-2483.5 MHz frequency band.
lOutdoor use: maximum power (EIRP*) of 100 mW for the 2400-2454 MHz band and with maximum power (EIRP*) of 10 mW for
the 2454-2483 MHz band.
Note:
Exposure to Radio Frequency Radiation To comply with RF exposure compliance requirements, a separation distance of at least
20 cm must be maintained between the antenna of this device and all person.
The technical documentation relevant to the above equipment will be held at: Primex | 965 Wells Street | Lake Geneva, WI 53147 |
Phone: [phone]
Company Representative:Mike O'Brien, General Manager
Signed:
8

SPECIFICATIONS - CLASSIC SERIES
Operation
12- or 24-hour time display
PM indicator light
Alternating time and date display option
LED dimmer option (100%, 75%, 50%, 25%)
Power outage memory backup for up to 8 hours
Power Over Ethernet (PoE)
PoE.IEEE 802.3af Compliant
Certifications: FCC/IC/CE marked
Actual power consumption: 12-Watts (Class 3)
Environment
Operating Temperature Range: 32° to 95° F (0° to 35° C); indoor use only
Storage Temperature Range: -20° to 185° F (-29° to 85° C)
Audible tone option - elapsed timer only
Audible tone only on count-up and count-down events
Audible tone frequency: 3 kHz +/- 0.5 kHz
9Classic Series Digital Clock/Timer Install Guide

Dimension Speci fications
Classic Digital Clocks/Timer dimensions
Clock Type Weight Max. Current Draw Height (A) Width (B) Depth (C)
2.5" (6.35 cm)
4-digit
2.26 lbs. (1 kg) 230 mA 5.0" (12.7 cm) 10.75" (27.30 cm) 2.5" (6.35 cm)
2.5" (6.35 cm)
6-digit
2.72 lbs (1.23 kg) 260 mA 5.0" (12.7 cm) 13.75" (34.93 cm) 2.5" (6.35 cm)
4" (10.16 cm)
4-digit
4.74 lbs. (2.15 kg) 230 mA 8.0" (20.32 cm) 18" (45.72cm) 3" (7.62 cm)
4" (10.16 cm)
6-digit
7.31 lbs (3.3 kg) 260 mA 8.0" (20.32 cm) 23.25" (59.05 cm) 3" (7.62 cm)
Classic Digital Clock/Timer Flush mount dimensions
Clock Type Weight Max. Current Draw Height (A) Width (B) Depth (C) Overall Depth Through Wall
2.5" (6.35 cm)
4-digit
2.88 lbs. (1.31 kg) 260 mA 6.3" (16 cm) 17" (43.18 cm) .2" (.5 cm) 2.6" (6.6 cm)
Classic Digital Clock/Timer Dual sided dimensions (use of dual clock bracket kit)
Mounted Dimensions
Clock Type Width from Wall (A) Height from Ceiling (B) Depth of 2 Clocks (C)
Dual 2.5”
4-digit
13.75” (34.93 cm) 8.0” (20.32 cm) 6.6” (16.76 cm)
Dual 2.5”
6-digit
16.8” (42.67 cm) 8.0” (20.32 cm) 6.6” (16.76 cm)
10

Mounted Dimensions
Clock Type Width from Wall (A) Height from Ceiling (B) Depth of 2 Clocks (C)
Dual 4”
4-digit
21.0”(53.34 cm) 11.0” (27.94 cm) 7.5” (19.05 cm)
Dual 4”
6-digit
N/A* 11.0” (27.94 cm) 7.5” (19.05 cm)
*4” 6-digit clock is not available as wall mount.
11 Classic Series Digital Clock/Timer Install Guide

Digital code blue and elapsed timer operation
Capability of functioning as a normal clock and timer with both count-up and count-down options. When power is applied it begins
operating as a digital clock.
Up counter features
lThe up counter can count up from any preset time to 99:59:59 (99 hours, 59 minutes, 59 seconds)
lThe decimal point on the far left (near the 10 hour digit) lights up to indicate up counter function
lThe user can preset count up start time
lUp-counters can count from 00:00:00 to 99:59:59 (99 hours, 59 minutes, 59 seconds). The display flashes every second and the
clock beeps for 3 seconds when 99:59:59 is reached.
Down counter features
lThe count-down timer can count down from a preset time to 00:00:00
lThe decimal point on the far right (near the minutes/seconds digits) lights up to indicate down counter function
lThe user can preset count-down start time
lDown counters can count from 99:59:59 to 00:00:00. The display flashes every second and the clock beeps for 3 seconds when
00:00:00 is reached
Elapsed Timer audible tone
lAudible tone only on count-up and count-down events
lFrequency: 3 kHz +/- 0.5 kHz
12

DIGITAL CLOCK/TIMER INSTALL - CLASSIC SERIES
Learn how to install and operate a Classic Series Digital Clock/Timer.

Install Requirements
Refer to the Important Safety Instructions before installing, operating or performing maintenance of clocks/timers.
Note:
Any damage to the clock or timer due to improper wiring voids the warranty.
Clock configuration
Before installation, verify the clock is configured for the network and can successfully check-in to your OneVue account at its
installation location. Commonly, a network is assigned to a clock during device preconfiguration.
Your OneVue account ID and the settings provided during device preconfiguration are configured into your clocks and each clock is
labeled before they are shipped from Primex.
Power-over-Ethernet (PoE) digital clocks/timers
Requires a connection to a PoE enabled LAN. PoE power is usually injected into the LAN using either PoE enabled Ethernet switches or
Mid Span power injectors. Consult with your IT department to verify the required PoE equipment is in place.
lSingle-sided PoE 802.3 af Input Power Specification - 48V, 12.9 watts max power
14 Classic Series Digital Clock/Timer Install Guide

Tilt Bracket and Wall Mount Dimensions - Classi c Series
Dimension D - clock screw hole spacing.
Dimension E - distance to wall surface for 4° mounting bracket
Dimension F - distance to wall surface for 18° mounting bracket
Dimension G/H - mounting bracket screw hole spacing.
Dimension
Clock/Timer Model A B C D E F G H
2.5” 4-digit 5.0” 10.75” 2.5” 6.0” 0.38” – 0.63” 2.1” 8.0” (4°), 9.5” (18°) 2.5”
2.5” 6-digit 5.0” 13.75” 2.5" 6.0” 0.38” – 0.63” 2.1” 8.0” (4°), 9.5” (18°) 2.5”
4” 4-digit 8.0” 18.0” 3.0” 14” 0.4 – 0.9” N/A 12.0” 4.0”
4” 6-digit 8.0” 23.3” 2.4" 14” 0.4 – 0.9” N/A 12.0” 4.0”
2.5” 6-digit flush-mount 6.3” 17.0” 0.3” N/A 0.5 – 1.0” N/A N/A N/A
4° mounting bracket (2.5”) 4.3” 8.8” N/A N/A N/A N/A 8.0” 2.5”
4° mounting bracket (4”) 7.8” 17.8” N/A N/A N/A N/A 12.0” 4.0”
18° mounting bracket (2.5”) 4.3” 10.6” N/A N/A N/A N/A 9.5” 2.5”
15

Tilt Bracket Digital Clock/Timer Instal l - Classi c Series
Supplied parts
(4) #10 Screw
(4) Anchor
(1) Bracket
AC-powered installation requirements
Hardwired (pigtial) installations require a 120V~ power line in a 4 in. x 4 in. junction box installed by a licensed electrician. The tilt
bracket has a center pass-through hole for the 120V~ pigtail.
If a junction box is present, the tilt bracket also has mounting holes spaced to allow direct attachment of the tilt bracket to the cover-
plate screw holes on the junction box.
The RJ-45 jack for the network cable is on the bottom of the clock/timer. Most building codes prohibit running network cables through
the same junction box as line voltage.
Tilt bracket installation illustration
You may mount the tilt bracket directly to the wall with four #10 screws and anchors. Refer to the Mounting Dimension Specifications
for the spacing of the screws. Refer to dimension Dfor the spacing of the screws. For more information, see "Tilt Bracket and Wall
Mount Dimensions - Classic Series" on the previous page.
16 Classic Series Digital Clock/Timer Install Guide

17

Wall Mount Digital Cl ock/Timer Install - Classic Series
Note:
Most building codes prohibit the use of hardwired power connections for devices that can be removed without tools.
Clock/timers mounted directly to a wall must have standard power plugs.
Supplied parts
(2) #10 Screw
(2) Anchor
How to mount a clock/timer to a wall surface
1. Mount the clock/timer directly to the wall with two #10 screws and anchors per the Tilt Bracket and Direct-Wall Mounting
Dimension Specifications. Refer to the Mounting Dimension Specifications for the spacing of the screws. Refer to dimension D
for the spacing of the screws. For more information, see "Tilt Bracket and Wall Mount Dimensions - Classic Series" on
page15.
18 Classic Series Digital Clock/Timer Install Guide

Flush Mount Di gital Clock/Timer Install - Classic Series
Supplied parts
(2) Screw, #6 x 1 1/4” flat head
(2) Anchor
Required materials AC-powered models (not supplied)
1 standard 2x4 cut to 14.5 in. (36.8 cm)
Digital clock model: 1 square shallow 4 x 4 (10.16 cm x 10.16 cm) junction box
Digital timer model: 2 square shallow 4 x 4 (10.16 cm x 10.16 cm) junction boxes
4 drywall anchors
How to install a flush mount clock/timer
1. Cut a 5.4 in. (13.71 cm) x 14.4 in. (36.57 cm) wall opening that is between two studs. Clearance within the wall should be at least 2.5
in. (6.35 cm) deep to allow for the clock assembly.
Note:
For Power over Ethernet (PoE) models steps 2 through 15 are not required. Proceed to step 15.
2. Secure a standard 2 x 4 cut to 14.5 in. (36.83 cm) between the two studs located 0.5 in. (1.27 cm) above the top of the bottom of
the opening and 2.4 in. (6.0 cm) from the front of the opening
19

3. Mount the junction box(es) as specified below:
Digital clock model - mount one junction box in the center of the opening and flush with the front side of the 2 x 4.
Digital timer model - mount two junction boxes, each to be 1 in. (2.54 cm) from the center of the opening and flush with the front
20 Classic Series Digital Clock/Timer Install Guide