Primex XR Classic Series User manual

©2016 Primex. All Rights Reserved. The Primex logo is a registered trademark of Primex. All other trademarks are the property of their respective owners. 12/3/2018. Primex, Inc. |
965 Wells Street | Lake Geneva, WI 53147 | www.primexinc.com | Ph: 1-262-729-4853
XR Classic Series Digital Clocks/Timers
Install Guide
Primex XR 72MHz Synchronized Time Solution

Legal Notice
Copyright ©2016 Primex, Inc. All rights reserved.
Printed in the USA.
Information in this document is subject to change without notice. Software described in this document is furnished under a license
agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of those
agreements.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical or otherwise, for any purpose, without the prior written permission of Primex, Inc.
Primex, Inc.
Primex is a leading provider of synchronized time and environmental monitoring solutions. Our solutions automate and maintain
facility compliance, increase efficiencies, enhance safety and reduce risk for organizations in the healthcare, education,
manufacturing and government vertical markets.
Worldwide Headquarters
965 Wells Street, Lake Geneva, WI 53147
Phone: [phone] | email: [e-mail] | www.primexinc.com
2XR Classic Series Digital Clocks/Timers Install Guide

Regulatory Compliance
FCC/IC Product Compliance
This device complies with part 15 of the FCC rules as well as with Industry Canada.
Operation of this device is subject to the following two conditions:
lThis device may not cause harmful interference.
lThis device must accept any interference that may cause undesired operation.
3

Important Safety Instructions
READ ALL INSTRUCTIONS BEFORE INSTALLATION, OPERATION, OR MAINTENANCE OF PRODUCT.
Important Safety Instructions
READ ALL INSTRUCTIONS BEFORE INSTALLATION, OPERATION, OR MAINTENANCE OF PRODUCT.
Some of the following information may not apply to your particular product model; however, as with any electronic product,
precautions should be observed during installation, operation, and maintenance.
lInstallation must conform to state or local building codes and ordinances.
lInstallation or maintenance should be performed only by qualified personnel as defined in the Local Electrical Code.
lMount in location where device will not readily be subject to tampering.
lAny wiring instructions must be followed precisely. Failure to do so could cause permanent equipment damage.
lTo avoid possible electric shock or damage to the device, disconnect power source before installation or servicing.
lDo not install or use device near water. To reduce the risk of electrical shock, do not expose device to rain or moisture. Device
must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, must be placed on the device.
lDevice is designed for indoor use only. Operating outdoors, or in wet areas, is an electrical hazard and may damage the
equipment while nullifying the warranty.
lDevice is cleanable with a cloth moistened with water or a common disinfectant. Be sure to test any cleaning solutions on a small
area of the clock before using it on the entire device.
lFor healthcare facilities, devices are not intended for patient use and must not be installed within 6ft (2m) of patient contact.
AC-Power Pluggable Clock/Timer Models
lAC main power supply must be disconnected while installing or performing maintenance of any device. To completely
disconnect the power input, the main plug should be disconnected from the main socket outlet completely.
lThe main socket outlet must provide a protective earthing connection where the outlet has a protective earth (ground)
connection.
lMain plug is used as disconnect device and it should remain readily operable during intended use.
AC-Power Hardwired Clock/Timer Models
lAC power must be supplied from a circuit that has a resettable circuit breaker.
lAC mains power supply must be disconnected while installing or performing maintenance of any device. Open the circuit
breaker supplying the device before attempting installation, maintenance, or repairs.
4

Contents
Specifications 6
Timer Switch Control Specifications 8
Configure Settings 11
Install Classic Series Digital Clock/Timer 15
Installation Requirements 15
Surface Mount Dimension Specifications 16
Tilt-Bracket and Surface Mount Mounting Dimensions 17
120VAC Wiring 18
24VAC Wiring Guidelines 18
Surface Mount Installation 19
Tilt-Bracket Installation 21
Dual Mount Installation 23
Dual-Sided Digital Clock Dimensions 25
Remove Digital Clock/Timer from Dual Mount Bracket 26
Flush Mount Installation 27
Remote Antenna Installation 33
Timer Switch Control Installation 36
Code Blue Timer Operation 38
Elapsed Timer Operation 39
Programmable Timer Operation 44
Support 45
Five Year Limited Warranty 46

Specifications
Model: Classic Series Digital Clocks and Timers
Parameter Specification
LED Display Highly visible 7-segment LED digits
2.5" model: 2.5” (6.4 cm) diagonal (hours and minutes), 1.4" (3.6 cm) diagonal (seconds)
4" model: 4.6” (11.7 cm) diagonal (hours and minutes), 2.5” (6.4 cm) diagonal (seconds)
LED Display Dimmer 100 %, 75 %, 50 %, 25 %
Time Display 12- or 24-hour time
PM indicator light
Alternating time and date display option
Hour Offset +/- 24 hours
Power Outage Memory Correct time stored in memory for a minimum of 8 hours without power
Receiver Sensitivity (Decode) < -110 dBm
6

Parameter Specification
Power Supply SNS and XR Classic Series: 120 VAC/ 50–60 cycle. Supplied with either a 9' (2.74 cm) cord
with plug or18" (45.72 cm) cord with pigtail
24VAC model: 18-28VAC/ 50–60 cycle. Supplied with a 10" (25 cm) cord with pigtail and
power supply
230 VAC - 50-60 cycle, 2 m cord (including plug); 45.72 cm (18”) also available
10 cm x 4 Digit: 69mA@ 230VAC, 16 Watts
10 cm x 4 Digit Dual: 134mA@ 230VAC, 31 Watts
10 cm x 6 Digit: 78mA@ 230VAC, 18 Watts
5.7 cm x 4 Digit: 69mA @230VAC, 16 Watts
5.7 cm x 4 Digit Dual: 139mA@ 230VAC, 32 Watts
5.7 cm x 6 Digit: 100mA@ 230VAC, 23 Watts
5.7 cm x 6 Digit Dual: 200mA@ 230VAC 46 Watts
Storage Temperature Range -20° to 185° F (-29°to 85° C)
Operating Temperature Range 32° to 194° F (0° to 35° C)
Code Blue Timer Input 5-120 VAC or DC
Code Blue and Elapsed Timer
Audible Beep Option
Frequency 3 KHz +/-0.5 KHz
ETL Listed Conforms to UL Standard for Safety for Time-Indicating and Recording Appliances (UL
863, 8th Edition, Date 11/16/2007)
All specifications are subject to change without notice.
7XR Classic Series Digital Clocks/Timers Install Guide

Timer Switch Control Specifications
The Primex 3 button Timer Switch Control provides the method manage events for both the Elapsed and Code Blue Timer. Elapsed
Timer count down or count up events are triggered manually by a user from the timer switch control buttons. Code Blue Timer
events are triggered by the input of the wired connection to the code blue system and the timer switch control allows a user to
pause a code blue event.
lDesigned to fit inside a single gang box (not supplied); typically 2 1⁄4 in. x 2 3⁄4 in. x 4 in. (11.45 cm x 6.99 cm x 10.15 cm).
lTimer Switch Control can simultaneously activate two connected timers for even more accurate event management.
lTimer Switch Control membrane switch and wall plate clean easily and resist common cleaners and disinfectants. Be sure to
test any cleaning solutions on a small area.
Elapsed Timer - Timer Switch Control operating specifications
The timer has three operating modes and a set state. The Timer Switch Control DISPLAY button sets the timer into each mode. The
RESET button sets the timer into its set state, allowing a user to set the start time for a count up or count down event.
Clock Mode Count-Up Mode Count-Down Mode Set State
10:45 02
Displays current synchronized
time
0.0:00 00
Decimal lit after the 10hr
digit
99:59 59.
Decimal lit after the 1 sec
digit
Set the start time for count
event.
Elapsed Timer - Count Mode operating specifications
The Timer Switch Control allows a user to start, stop, pause and reset the timer. When not in a count mode, the timer displays its
synchronized time.
Pressing the
button... Clock Mode Count Up Mode Count Down Mode
DISPLAY
EXIT
Pressing and releasing the DISPLAY button scrolls through the various modes in the following order:
1. Clock Mode
2. Count Up Mode
3. Count Down Mode
8

Pressing the
button... Clock Mode Count Up Mode Count Down Mode
STOP/START
INCREMENT
Ignored Controls the count up event while in count up
mode.
If the count event is started, pressing and
releasing the STOP/START button stops and
pauses the event.
If the count event is stopped/paused, pressing
and releasing the STOP/START button resumes
the event.
Controls the count down event while in count
down mode.
If the count event is started, pressing and
releasing the STOP/START button stops and
pauses the event.
If the count event is stopped/paused, pressing
and releasing the STOP/START button resumes
the event.
RESET
SET/CHANGE
Ignored Pressing and releasing the RESET button once
automatically stops and resets the count event
to its preset start time.
Or
Holding the RESET button puts the timer into
SET STATE.
Pressing and releasing the RESET button once
automatically stops and resets the count event
to its preset start time.
Or
Holding the RESET button puts the timer into
SET STATE.
Elapsed Timer - Set State operation specifications
The Set State is used to set the start time for a count up or count down event. Enter the Set State by holding the RESET button
while in count up or count down mode.
In this state:
lThe text labeled on the bottom of the switch control button is applicable (SET/CHANGE, INCREMENT, EXIT).
lThe dash, colon, and decimal points are not displayed.
lThe digit that is currently being set will flash.
Pressing the
button... Count Up Mode Count Down Mode
DISPLAY
EXIT
Exits Set State Saves the start time and exits the Set State
STOP/START
INCREMENT
Increments the selected digit Increments the selected digit
9XR Classic Series Digital Clocks/Timers Install Guide

Pressing the
button... Count Up Mode Count Down Mode
RESET
SET/CHANGE
Holding the SET/CHANGE button for 3 seconds enters
the set state, which is indicated by “ _ _:_ _ _ _” on the
display.
The selected digit will blink.
Pressing SET/CHANGE again to select the next digit.
Holding the SET/CHANGE button for 3 seconds enters
the set state, which is indicated by “ _ _:_ _ _ _” on the
display.
The selected digit will blink.
Pressing SET/CHANGE again to select the next digit.
Code Blue Timer - Timer Switch Control operating specifications
The Timer Switch Control allows a use to halt a code blue event.
Pressing the
button... Running Mode Halted Mode
DISPLAY
EXIT
Ignored Places display back in clock mode
Holding down DISPLAY for a minimum of four seconds shows the last code blue time.
RESET
SET/CHANGE
Ignored Ignored
STOP/START
INCREMENT
Halts the code blue event count at the moment the button is
pressed.
Ignored
10