Primo Water HDCAR82x16-TA User manual

HDCAR82x16-TA
HDCAR82x18-TA
HDCAR82x20-TA
HDCAR82x16-TA-10K
HDCAR82x18-TA-10K
HDCAR82x20-TA-10K
ASSEMBLY INSTRUCTIONS
AMERICA’S HIGHEST BEST REVIEWED ALUMINUM TRAILER MANUFACTURER
WWW.PRIMOTRAILER.COM
Read this INSTRUCTIONS before using this product.
Failure to follow the safety rules and other basic safety
precauons may result in serious personal injury.
SAVE these instrucons for future reference.
WARNING

HDCAR-TA, HDCAR-TA-10K Assembly Instrucons V:04/222
SAFETY & PRECAUTIONS
CAUTON
WARNING
Serious injury and/or property damage can result if
this vehicle iys towed before familiarizing yourself
with the instructions in the owners manual and
cautions listed to the right.
You are required to comply with local and state
requirements regarding brakes, licensing and
any additional equipment that may be necessary.
Contact your state motor vehicle department for
more information.
• Coupler hitch and trailer ball are the same size
• Coupler is latched
• Safety chains are criss-crossed under tongue and
hitched to towing vehicle
• All trailer lighting is working correctly
• Loading is secured to trailer front and rear
• Tongue jack (if trailer is equipped) is retracted
• Tilt pin is latched
• Wheel lug bolts are properly tightened
• Tires are inated to pressure indicated on tire
• Trailer brakes (if trailer is so equipped) are properly
adjusted and break away device is attached to
towing vehicle
• Load is within trailer capacity and distributed
properly to maintain proper tongue weight
• Heavy end of load must go onto the trailer rst
• When approaching trailer, drive on slowly
• High speed loading can result in over shooting front
of trailer, and result in injury
• Wet surfaces may cause slick bed surface
• Use caution while loading on wet bed
BEFORE TOWING THIS
DANGER
US2023
TRAILER CHECK THAT:

HDCAR-TA, HDCAR-TA-10K Assembly Instrucons V:04/223
SAFETY & PRECAUTIONS
Uncoupling will cause trailer to come loose from tow
vehicle. You must:
1. CHECK that ball LOAD HATING is same as or greater
than coupler LOAD RATING.
2. CHECK that ball SIZE is same as coupler.
3. CLOSE COUPLER CLAMP on ball.
4. LIFT coupler upwards to test that it will not separate
from ball.
5. LOCK coupler clamp with pin or padlock.
WARNING
©2022 NATM UT0016
ALWAYS use safety chains.
Chains hold trailer if connection fails.
You must:
1. CROSS chains underneath coupler.
2. ALLOW slack for trailer to turn.
3. ATTACH chain hooks securely to tow
vehicle frame.
WARNING
©2022 NATM UT0020
Trailer can roll if it comes loose.
Electric safety brake applies when cable pulls pin out of
switch box.
1. PULL hard to get pin out of switch box.
2. CHECK brake by PULLING TRAILER with tow vehicle.
3. ATTACH pin CABLE to tow vehicle so pin will be
pulled out if trailer separates.
4. Promptly REPLACE pin in switch box.
WARNING
©2022 NATM UT0035
Lights can prevent trailer from being hit by other
vehicles. You must:
1. CONNECT trailer and tow vehicle electrical
connectors.
2. CHECK all ghts: tail lights, turn signal, and
brake lights.
3. DO NOT TOW if lights are not working.
WARNING
©2022 NATM UT0026
Tire, wheel or lug nut failure can cause loss of control.
Before towing, you must CHECK:
1. Tire pressure and tread.
2. Tires and wheels for damage.
3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts
at the rst 10, 25 and 50 miles of driving.
WARNING
©2022 NATM UT0019

HDCAR-TA, HDCAR-TA-10K Assembly Instrucons V:04/224
PARTS, HARDWARE & TOOLS
PART NO.
1
2
3
4
5
6
7
ITHEM Main
frame
Ramp
holders
Loading
ramp
Stabilizer
jack Fender Fender support Tire
QTY 1 2 2 2 2 2 4
LABEL HW-8 HW-12 HW-13
NAME Fender Front Wall Fender Support
BOLT M8-130 x8 M10-150 x4 M8-150 x4
NUT M8 x8 M8 x4 M8 x4
WASHER M8 x8 M8 x4 M8 x4
TOOLS NEEDED
Impact drill10, 13, 18mm socket 10, 13, 18mm wrench
PART LIST
HARDWARE LIST
Wire strippers Trailer light tesng box
1
2
2
3
3
4
4
5
5
7
7
7
7
6
6
HW-8
HW-8
HW-8
HW-8
HW-13
HW-13
HW-12
HW-12

HDCAR-TA, HDCAR-TA-10K Assembly Instrucons V:04/225
PREPARATION
HW-12
2
3
4
STEP 1
1. Cut all zip es and banding.
2. Gather the hardware packages.
3. Gather both driver and passenger side
fenders and 2 fender supports.
4. Gather 2 stabilizer jacks.
5. Gather 2 loading ramps and 2 ramp
holders.
1.
2.
3.
4.
5.
HW-8
HW-13
1
2
3
4
5
5
6
6