Pro 1 IAQ T605-2 User manual

Operation ManualOperation Manual

U.S. Registered Trademark. Patents pending
Copyright 2018 All Rights Reserved.
T605-2
Pro1 Technologies
Toll Free: 888-776-1427
Web: www.pro1iaq.com
Hours of Operation: M-F 9AM - 6PM Eastern
Table of Contents
Table of Contents
Thermostat Quick Reference
Thermostat Operation
Warranty Information
Page
2-4
5-6
7
1
Una version en español
de este manual se puede
descargar en la pagina web
de la compañia.
Equipment damage hazard.
Do not operate the cooling
system if the outdoor
temperature is below 50 ˚F
(10 ˚C) to prevent possible
compressor damage.
Caution:
Rev. 1823
P.O. Box 3377
Springeld, MO 65808-3377

FAN
ON AUTO
SYSTEM
COOL OFF HEAT
Set At
LEAVE
AM
Hold/Run
Time
Program
Thermostat OperationThermostat Operation
LCD Display
Fan Switch
System Switch
See page 4 for details about
this display read out.
Select ON or AUTO. ON will
run the fan continuously.
AUTO will cycle the fan on
only when the heating or
cooling system is on.
Selects the operation mode
on your HVAC system.
Selecting HEAT turns on
the heat mode. Selecting
COOL turns on the air
conditioning mode.
Selecting OFF turns both
heating and cooling o.
When the battery icon appears replace your AA
batteries immediately. Failure to do so may result in your
heating & cooling system becoming inoperable. Freezing or
over heating can occur.
Caution:
User Buttons
Use these buttons to set up
your programming options.
Refer to the next page for
detail.
Temperature Setpoint Buttons
Press the + or - buttons to
select the desired room
temperature.
Fan Switch
System Switch
Temperature Setpoint Buttons
LCD Display
User Buttons
Easy Change Battery Door
See page 5 for details.
Easy change battery door

Set At
COOL ON
WAKE
Sun Mon Tue Wed Thu Fri Sat
ON
LEAVE
RETURNSLEEP
AMPM
HOLD
Thermostat Quick Reference Thermostat Quick Reference
The low battery icon is displayed when the AA battery power is low. Whenever the
thermostat detects low battery voltage from the AA batteries, the low battery icon
will begin ashing on the screen for 21 days (if the batteries are not changed). If the
batteries are not changed 22 days after the thermostat detects low battery
voltage, the thermostat screen will only show the ashing battery icon until
buttons are pressed. If the batteries are not changed 43 days after the thermostat
detects low battery voltage, the thermostat screen will only show the ashing
battery icon until buttons are pressed and the set points will oset to 85°F/29°C
in cooling and 55°F/13°C in heating. At this stage, set point changes can be made
temporarily but, the set points will change back to defaulted values after a 4-hour
period. The thermostat will continue to perform this low battery ashing,
temperature oset condition until the internal voltage threshold is reached. When
the thermostat internal voltage threshold is reached, all relays will be opened and
the thermostat will become inoperable until new batteries are installed.
Important:
Battery Door Information
Use the nger bevel on
the lower portion of the
thermostat to open the
easy access battery door.
Replace with
2 AA Alkaline
Batteries. High
quality Alkaline
batteries are
recommended.
Simple operating instructions are
found on the back of the battery door.
Indicates the current room temperature
Time and day of the week
Setpoint: Displays the user selectable setpoint temperature.
Hold is displayed when the thermostat program is permanently overridden.
System Operation Indicators: ON will display when the COOL
or HEAT is on. Compressor delay feature is active when ashing.
Low Battery Indicator: Replace batteries when this indicator is shown.
Program Time Periods: This thermostat has 4 programmable time periods
per day.
7
7
HEAT

Thermostat Quick ReferenceThermostat Quick Reference
Temporary and Permanent Hold Feature
Note: This is a programmable thermostat, and will always be
running a programmed schedule. However, it can be
overidden with a Temporary or Permanent Hold.
Temporary Hold: With the system in Heat or Cool, anytime the set-at
temperature is changed with the + or - buttons, the thermostat will
enter a Temporary Hold. This will be indicated by “HOLD” ashing
and will remain in this hold until the next programmed time period
begins.
Permanent Hold: To enter a Permananet Hold, press the Hold/Run
button while “HOLD” is ashing. The word“HOLD” will remain on
continuosly, indicating a Permanent Hold.
To Return to Running Schedule: To manually exit this hold and
return to scheduled program, press Hold/Run button or cycle the
System Switch.

Programming The Thermostat
1. Press TIME
2. Day of the week will be ashing. Use the or key
to select the current day of the week.
3. Press TIME
4. The current hour is ashing. Use the or key to
select the current hour. When using 12-hour time, make
sure the correct a.m. or p.m. choice is selected.
5. Press TIME
6. Minutes are now ashing. Use the or key to
select current minutes.
7. Press HOLD/RUN when completed.
Set Time
To customize your program schedule, follow these steps
Weekday:
Set Program Schedule
Programming The Thermostat
Continued on next page...
1. Select HEAT or COOL with the system switch. Note: You have
to program heat and cool each seperately.
2. Press the PROGRAM
3. Monday-Friday is displayed and WAKE is shown. You are now
programming the wake time period for the weekday setting.
4. Time is ashing. Use the or key to make your time
selection for the weekday WAKE time period.
5. Press PROGRAM
6. The setpoint temperature is ashing. Use the or key
to make your setpoint selection for the weekday wake period.
7. Press PROGRAM
8. Repeat steps 4 thru 7 for weekday LEAVE time period, for
weekday RETURN time period, and for weekday SLEEP time
period.

Warranty Information
Warranty Registration
Your new thermostat has a 2 year limited warranty. You must register
your thermostat within 60 days of installation. Without this
registration the warranty period will begin on date of manufacture.
For warranty issues please contact the HVAC professional that
installed this product. You can register your new thermostat in 2 ways:
Go to the company website, select warranty registration and
ll out a short registration form.
Complete the form below and mail it to the address shown.
Warranty Registration
Complete form and mail to:
Thermostat Warranty Registration
Online
Mail
Repeat steps 4 thru 7 for Saturday WAKE time period, LEAVE
time period, RETURN time period, and for Saturday SLEEP time
period.
Saturday:
Repeat steps 4 thru 7 for Sunday WAKE time period, LEAVE
time period, RETURN time period, and for Sunday SLEEP time
period.
Sunday:
To customize your program schedule, follow these steps
Set Program Schedule
Programming The Thermostat
Pro1iaq
P.O. Box 3377
Springeld, MO 65808-3377
Name:
Address:
City:
State:
Zip:
Thermostat Model:
Date Installed:

www.pro1iaq.com
Cut Out For
Warranty Registration