Pro DVX IPPC-10 SLB User manual

Quick start
guide
The information in this document is subject to change without notice. © 2022 ProDVX Europe B.V. All rights reserved.
IPPC-10 SLB
Please check the website or scan the QR-code for more product information.
www.prodvx.com/support
IPPC-10 SLB

This package contains:
How to start:
Quick connection settings
IPPC-10SLB Quick start guide
*Please note that it is prefered not to use power
tools to attach the device to the mount or stand.
Step 1: Take contents out of the box, make sure all components are present.
Step 2: Install wall/glass mount or desk stand using manual screw driver, check designated mount/stand
manual for instructions.
Step 3: Connect to power via power adapter or PoE+.
Step 4: Connect to Internet through Wi-Fi, PoE+, or LAN.
Step 5: If applicable, install and configure preferred application.
Optional accessories
Landscape Camera
Portrait
Backside
Pogo pin connector Strain relief
Speaker Speaker
VESA 75 mount
Screw spec: M4*4 mm
Bottom view
LAN port
Type A USB port
Micro-USB / OTG
GPIO
Mounting screw hole
HDMI out
Audio port 3.5 mm
12 V DC-in
Top view
On / o button
SD-Card slot
(with cover)
Back / home button
Scroll up / down button
Volume + and -
Tools necessary
but not included
IPPC-10SLB Quick start guide
Step 1: Plug in power cable to turn on display.
To connect to Wi-Fi, navigate to the bottom toolbar
and click the globe icon as seen in the image below.
Step 2: Select the desired Wi-Fi network,
click “connect” and fill in credentials to connect.
Barcode scanner NFC module Camera
1. When powering on the device, select Wi-Fi by pressing and holding the volume plus-button.
2. If you would like to switch back to the ethernet connection, make sure the device is powered down. Aer that,
press and hold the volume minus-button while turning on the device to revert back to ethernet.
If the procedure is performed correctly, a notification will be shown stating which connection is now active.
Important notice
Whenever you want to switch between the Wi-Fi connection and
ethernet connection, the following procedure can be used:
Caution:
Please note this product contains a small clock battery. Please return the product to a
certified repair centre for proper replacement of the battery; battery disposal can be
dangerous.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequen-
cy energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a
residential area can cause harmful interference, in which case the user will be required to
correct the interference at their own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Europe/UK – EU/UK Declaration of Conformity
This device complies with the essential requirements of the Radio Equipment Directive
(2014/53/EU). The following test methods have been applied in order to prove presump-
tion of conformity with the essential requirements of the Radio Equipment Directive.
This equipment is compliant with Class A of EN55032. In a residential environment, this
equipment may cause radio interference.
Correct Disposal of this product.
This marking indicates that this product should not be disposed of with other
(household) waste. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustain-
able reuse of material resources. To return your used device, please use the return and
collection systems or contact the reseller where the product was purchased. They can
take this product for environmentally safe recycling.
“FCC & CE RF Radiation Exposure Statement Caution: To maintain compliance with
the FCC & CE’s RF exposure guidelines, the product must be placed at least 20cm from
nearby persons.”
The guaranteed environmental specifications for the ProDVX Display and accessories are:
- Operating temperature: : 0 – 40 °C / 32 - 104 °F
- Storage temperature: -10 - 55 °C / 14 - 131 °F
- Relative humidity: 10 - 85% at 40 °C / 104 °F non-condensing