Xandex Kubi Enhanced Audio Kit Manual
SETUP INSTRUCTONS
SETUP INSTRUCTONS
Connect the AC power cord to
the USB charger. Connect the
AC power cord to a 100-240
VAC power source.
Note: The USB charger may
also be used to connect the
charging cables for KUBI and
the tablet.
Plug the 3.5 mm side connector
on the microphone into the
earphone port on the tablet.
Rotate the microphone so it
points the same direction as the
tablet screen.
Plug one end of the audio cable
into the earphone port on the
end of the microphone.
Plug the other end of the audio
cable into the AUDIO IN port on
the speaker.
Plug the mini USB cable into
the DC IN port on the speaker.
Connect the other end of the
USB cable into one of the ports
on the USB charger.
Turn the speaker power switch
to ON
Play an audio le on the tablet
and adjust speaker volume
using the tablet’s volume con-
trol buttons.
kubi Enhanced Audio Kit
Copyright © 2017 Xandex Inc. 1360 Redwood Way, Suite A, Petaluma CA 94954
TEL: (707) 763-7799 EMAIL: [email protected] For more infomation visit www.revolverobotics.com P/N 180-0135r1
kubi Enhanced Audio Kit
KUBI SECURE INSTALLATION
KUBI SECURE INSTALLATION
INSTRUCTONS
INSTRUCTONS
NOTE:
NOTE:
If you are installing the speak-
er bracket on an already assembled
kubi secure, remove the arms from
the kubi by removing the two arm
retention screws. Retain screws for
re-assembly.
Kubi Secure Arms are shipped
with foam pads attached. Two of
these pads (red arrows) must be
removed to install the Audio Kit
Speaker Bracket.
Peel the bottom two pads off of
the arms (red arrows in item 1) and
remove all adhesive from the arms.
An adhesive solvent may be
required, like acetone or Goo
Gone®.
Align the right arm over the thread-
ed insert on the kubi. Orient the
speaker bracket over the arm as
shown, and install one of the small
center-pin torx screws using the
kubi wrench. Wrench and screws
are supplied with the kubi (not the
audio kit).
Slide the left arm into place behind
the speaker bracket and align the
at edge to the at edge on the
right arm (red arrow in image #2).
Rotate the speaker bracket down
into place.
Install one of the small center pin
torx screws using the kubi
wrench.
After both screws are in place,
visually inspect the alignment of
the arms. They should be cen-
tered on the kubi housing with the
speaker bracket at against the
arms.
Copyright © 2017 Xandex Inc. 1360 Redwood Way, Suite A, Petaluma CA 94954
TEL: (707) 763-7799 EMAIL: [email protected] For more infomation visit www.revolverobotics.com P/N 180-0135r1
kubi Enhanced Audio Kit
KUBI CLASSIC AND PLUS
KUBI CLASSIC AND PLUS
INSTALLATION INSTRUCTONS
INSTALLATION INSTRUCTONS
IMPORTANT! The goal of this
procedure is to install the
speaker bracket WITHOUT
LIFTING, MOVING OR REMOV-
ING THE ARMS. IF THE ARM
SPRINGS BECOME DISEN-
GAGED, A SEPARATE OPERA-
TION MUST BE PERFORMED!
IDENTIFY WASHER TYPE:
White Plastic or Stainless Steel
Stainless Steel Procedure:
Keep downward pressure on
the arm and use the supplied
Allen wrench to remove the
right screw and metal washer.
Keep downward pressure on
the arm and place the audio
speaker bracket over the right
arm bushing and install the
retaining screw. Tighten so the
bracket can still be rotated.
Remove the left arm screw and
metal washer.
Rotate the bracket down and
install the left screw. Tighten
both screws.
After installation of the bracket,
the arms should be retracted in
upright position.
If arms do not move freely, and
close completely on their own,
loosen arm screws slightly until
arms open and close freely.
WHITE STAINLESS
Copyright © 2017 Xandex Inc. 1360 Redwood Way, Suite A, Petaluma CA 94954
TEL: (707) 763-7799 EMAIL: [email protected] For more infomation visit www.revolverobotics.com P/N 180-0135r1
kubi Enhanced Audio Kit
KUBI CLASSIC AND PLUS
KUBI CLASSIC AND PLUS
INSTALLATION INSTRUCTONS
INSTALLATION INSTRUCTONS
IMPORTANT! The goal of this
procedure is to install the
speaker bracket WITHOUT
LIFTING, MOVING OR REMOV-
ING THE ARMS. IF THE ARM
SPRINGS BECOME DISEN-
GAGED, A SEPARATE OPERA-
TION MUST BE PERFORMED!
IDENTIFY WASHER TYPE:
White Plastic or Stainless Steel
White Plastic Procedure:
Use the supplied Allen wrench
and remove the screw from the
right washer.
Keep downward pressure on
the arm and carefully remove
the washer.
Replace the washer with one of
the supplied white nylon bush-
ings.
Place the audio speaker brack-
et over the right arm bushing
and install the retaining screw.
Tighten so the bracket can still
be rotated.
Remove the left arm screw and
washer and install a white nylon
bushing.
Rotate the bracket down and
install the left screw. Tighten
both screws. If arms do not
move freely, loosen arm screws
slightly until arms open and
close freely.
WHITE STAINLESS
Copyright © 2017 Xandex Inc. 1360 Redwood Way, Suite A, Petaluma CA 94954
TEL: (707) 763-7799 EMAIL: [email protected] For more infomation visit www.revolverobotics.com P/N 180-0135r1
Table of contents
Other Xandex Tablet Accessories manuals
