Pro-Ject Audio Systems Measure it E User manual

© Pro-Ject Audio Systems · Measure it E · Revision 02.09.16
Thank you for purchasing a Pro-Ject Audio Systems stylus balance.
!
Warning of a hazard for the user, the unit or possible misuse
Important notice
What is in the box
•stylus balance
•calibration weight (5 g)
•2 LR43 (AG12) button cell batteries plus 2 pieces as backup
•protection pouch for the meter
•user guide
Calibration
1 Make sure the surface is level.
2Turn on the meter with the ON/OFF button. The display will show 0.000 after a few seconds.
Give your stylus balance sufficient warm up time. Usually 30 seconds give the internal
components time to stabilise before calibrating.
3Press and hold the MODE button until the display shows CAL and then press the MODE button
again, the display will show 5.000 (flashing) after CAL (flashing).
4Gently place the 5g weight on the centre of the platform. After approximately 5 seconds the
display will read 5.000, PASS and 5.000.
Occasionally the display will show for example 5.002 or 5.004 instead of 5.000. This is
no defect. It will not affect the calibration.
5Remove the weight and press ON/OFF to turn off the meter.
Choosing the weighting mode
The meter has to be turned on. The display shows 0.000. Pressing the MODE switches between the
different weighting modes.
Weighting modes: gram (1g = 10mN), ounce (oz), pennyweight (dwt) and carat (ct).
Cartridge downforce adjustment - weighting mode gram
1 Make sure the surface you use the turntable on is level.
2Remove the stylus guard and the stylus balance protection cover. Gently place the meter on the
platter. Move the headshell over the weighting platform and place the tip of the needle above the
black dot of the weighting platform.
3Turn on the stylus balance with the ON/OFF button. The display will show 0.000 after a few
seconds. Give your meter sufficient warm up time. Usually 30 seconds to give the internal
components time to stabilise.
4Gently lower the tonearm until the stylus is on the black dot of the weighting platform. The display
shows the tracking force.
5Lift the tonearm and adjust the counter weight (tracking weight dial) and repeat the above
procedure until the recommended tracking force is achieved.
!
Never load the stylus balance with more than 5g, overloading can permanently damage it.

© Pro-Ject Audio Systems · Measure it E · Revision 02.09.16
Backlight
Turn on the stylus balance and the backlight will automatically switch on (no further key switch
needed). When the stylus balance is switched off, the backlight will switch off.
Other display readouts
No display, backlight getting weak - batteries are empty and need to be replaced.
o_LD - overload (more than 5g). Please remove the excessive load immediately.
LLLLL - The weighting load cell has been damaged by misuse (i.e. it was shocked, dropped or
overloaded). You can try to recalibrate the meter. If the load cell has not been damaged to
much, it will work again after recalibration.
UNSt - Use the meter on a more stable, vibration free surface.
Changing batteries
Proceed as follows:
•Take off both battery case covers
•Replace both batteries together. Make sure the batteries are the right way round
•Refit the battery case covers
Battery type: 2 x LR45 (AG12) button cells, 1,5V
If the stylus balance is not used over a long period of time the batteries should be removed.
Do not dispose the batteries as ordinary domestic refuse. Please d
ispose your exhausted
batteries at the appropriate collection sites -
usually located at supermarkets and
drugstores.
Technical specifications Measure it E
Capacity 0 - 5g
Variance ±0,002g
Weighting modes gram (1g = 10mN), ounce (oz), pennyweight (dwt) and carat (ct)
Display 4 digit LCD with backlight
Calibration auto calibration using a 5g weight
Auto off 30 seconds off
Replacement battery 2 x LR43 (AG12) button cells, 1,5V
Operating temperature +10 - +30°C (50 - 86 degrees Fahrenheit)
Dimensions (W x H x D) 96 x 21 x 43mm
Weight 49g
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these
instructions for use. Modification or change to any part of the product by unauthorized
persons, will release the manufacturer from any liability over and above the lawful rights of
the customer.
Pro-Ject Audio Systems is a Registered Trademark of
H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems
Copyright © 2016. All rights reserved.
The information was correct at the time of going to
press. The manufacturer reserves the right to make
changes to the technical speci
fication without prior
notice as deemed necessary to uphold the ongoing
process of technical development.