Pro-Ject Audio Systems Box S USB User manual

INSTRUCTIONS FOR USE
Pro-Ject Switch Box S

© Pro-Ject Audio Systems · Pro-Ject Switch Box S (from S/N: F37853) · Revision 2015.10.30.
2
Dear music lover,
thank you for purchasing a Pro-Ject Audio Systems´ input expander.
In order to achieve maximum performance and reliability you should study these instructions for use carefully.
Warning of a hazard for the user, the unit or possible misuse
Important notice
Safety instructions
Please note that the back side of front panel edges can be sharp! Please handle carefully!
AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the
voltage in your area meets the voltage requirements printed on the power supply.
The power supply is used to connect/disconnect the unit from the mains. Make sure that the power
supply is easily accessible at all times. Never handle the device, the power supply while your hands are
wet or damp.
Avoid letting liquids enter the device or the power supply. Never place any item containing liquid,
such as a flower vase on or near the device. Never spill any liquid on the device or the power supply.
Never place any naked flame sources, such as lighted candles on or near the device. The product shall not
be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.
Connectors
Make all connections whilst the input expander is disconnected from the power supply.
Take care to connect the left and right channels correctly. The right channel is usually marked red,
the left channel black or white.
Never use any other power supply than the one supplied with the unit.
Outputs
Out has to be connected to the In 2 of the Pro-Ject Pre Box S. Out 2 can be used to connect a Pro-Ject
headphone amplifier, like the Head Box S ore the Head Box DS.
Inputs
Line level sources such as CD player tuner or TV can be connected to the input sockets marked In 2 - In 5.
!
!
!

© Pro-Ject Audio Systems · Pro-Ject Switch Box S (from S/N:F37853) · Revision 2015.10.30.
3
Trigger (Pro-Ject Pre Box S only)
The socket marked Trigger Switch on the Pro-Ject Pre Box S provides a trigger signal for the Switch Box S.
The trigger signal permits automatic synchronization with the input selector of the Pro-Ject Pre Box S.
A 30cm long trigger cable is supplied with the Pro-Ject Switch Box S for connecting the socket Trigger Switch
on the Pro-Ject Pre Box S and the socket Trigger on the back of the Pro-Ject Switch Box S.
Do not use the trigger input and output for any other connections for which it is not designed.
Mains power connection
Connect the low voltage plug from the power supply to the Power 9V DC socket before connecting the power
supply to the mains.
Selecting an input together with a Pro-Ject Pre Box S
After the unit is powered on, pressing the grey button next to the two LEDs selects the inputs In 1 to In 5 in
turn. Select the inputs using the remote control buttons marked CH-or CH+.
The selected input will be shown by the corresponding LED.
The dark grey button on the front of the Switch Box S is without function when the Switch Box S is
connected to a Pro-Ject Pre Box S via the supplied connecting cable.
Selecting an input together with a Pro-Ject Receiver Box, Stereo Box and Pre Box DS
Selecting an input when used with an amplifier from another manufacturer
Press of the button on the left side turn the unit on, short pressing of the same button selects the inputs In 2
to In 5 in turn. The selected input will be shown by the corresponding LED on the Switch Box S. Long press of
the button turns the unit off.
Pre Box S

© Pro-Ject Audio Systems · Pro-Ject Switch Box S (from S/N: F37853) · Revision 2015.10.30.
4
Technical specifications Pro-Ject Switch Box S
Gain: 0dB
Line-level inputs: 1 pair RCA/phono sockets, 3 x 3-pole 3,5mm co-axial jack
Line-level outputs: 1 pair RCA/phono sockets, 1 x 3-pole 3,5mm co-axial jack
Trigger: digital switching signal
Trigger in: 2-pole 2,5mm co-axial jack
Outboard power supply: 9V/300mA DC, suitable for your country's mains supply
Power consumption: 30mA DC
Dimensions W x H x D (D with sockets): 103 x 36 x 104 (109)mm
Weight: 580g without power supply
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information,
please contact your dealer for further advice. Only when the problem cannot be resolved there should the
unit be sent to the responsible distributor in your country.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions
for use. Modification or change to any part of the product by unauthorized persons, release the
manufacturer from any liability over and above the lawful rights of the customer.
Copyright, trademarks
Pro-Ject Audio Systems is a Registered Trademark of
H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems
Copyright ©2015. All rights reserved.
The information was correct at the time of going to
press. The manufacturer reserves the right to make
changes to the technical specification without prior
notice as deemed necessary to uphold the ongoing
process of technical development.