Pro-Ject Audio Systems Debut Carbon Phono/USB User manual

INSTRUCTIONS FOR USE
Pro-Ject Debut Carbon Phono/USB

© Audio Trade GmbH · Pro-Ject Debut Carbon/Phono USB / Ortofon OM10 · Revision 2013.11.15
2
10
11 12
2
3
4
5
11 11
21
0
30 5
20
8
6
16
6a
18
9
17 15
7
9a
17
3a
22
14
13
9a
1
1
19
23
22

© Audio Trade GmbH · Pro-Ject Debut Carbon/Phono USB / Ortofon OM10 · Revision 2013.11.15 3
Pro-Ject Debut Carbon Phono/USB
Controls, features and connections
1 Motor brackets with Sorbothane®pads
2 Stepped drive pulley
3 Drive belt * 3a Hook *
4 Hub
5 Platter with felt mat *
6 Tonearm counterweight * 6a Downforce scale
7 Tonearm lift lever
8/18 Tonearm rest and removable transport lock
9 Tonearm tube 9a Tonearm base
10 Lid *
11 Lid hinges
12 Hinge fasteners
13 Mains lead
14 Phono output sockets, earth connection and USB-out
15 Anti-skating stub with anti-skating weight adjustment scale
16 Anti-skating weight *
17 Anti-skating weight support hoop
19 Power switch
20 Headshell with finger lift and fitted Ortofon OM 10 cartridge
21 Motor
22 Single adapter *
23 3,5mm connector *
Connection cable (not shown) *
Dear music lover,
thank you for purchasing a Pro-Ject Audio record player.
In order to achieve maximum performance and reliability with this record player you should study these instructions
for use carefully.
!
Warning of a hazard for the user, the unit or possible misuse.
Important notice.
** Your turntable has been delivered with a factory fitted and adjusted cartridge, please ignore the cartridge set
up instructions unless changing the cartridge at a later date.
During assembly and adjustment of the deck small parts could be lost if not carefully placed in a suitable
receptacle. Before starting assembly make yourself acquainted with the parts listed above and correspondingly
numbered in the technical drawings above. Separately packed items are marked with an asterisk *.
Safety instructions
!
AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the
voltage in your area meets the voltage requirements printed on a label underneath the unit.
The power cord plug and the power switch (19) are used to disconnect the unit from the mains. Make
sure that the plug and the switch are easily accessible at all times. Hold the plug when unplugging
the power cord. Never handle the power cord while your hands are wet or damp.
Avoid letting liquids enter the device. Never place any item containing liquid, such as a flower vase
on or near the device. Never spill any liquid on the device. Never place any naked flame sources,
such as lighted candles on or near the device. The product shall not be used in damp or wet locations,
next to a bathtub, sink, swimming pool or any other similar conditions.
Keep plastic bags away from children to prevent any risk of suffocation.

© Audio Trade GmbH · Pro-Ject Debut Carbon/Phono USB / Ortofon OM10 · Revision 2013.11.15
4
Set-up
The deck is supplied partially disassembled and carefully packaged for safe transport. Carefully remove all
parts from the transport packaging.
Make sure the surface you wish to use the turntable on is level (use a spirit level) before placing the turntable on it.
Remove the transport lock (18) from the tonearm. Store it in the original packaging so it is available for any
future transportation.
Fit the drive belt (3) around the hub (4) and the smaller diameter part of the motor pulley (2). Avoid getting
sweat or grease on the belt as these will deteriorate the performance and reduce the belt's lifespan. Use
absorbent kitchen paper to remove any oil or grease from the outer edge of the hub and the belt. Fit the
platter (5) and felt mat over the spindle of the hub (4).
Cartridge downforce adjustment
The counterweight (6) supplied is suitable for cartridges weighing between 4,5 - 6g (weight no. 8
80
). An
alternative counterweight for cartridges weighing between 6,5 - 8,5g (weight no. 0
08
) is available as an
accessory part.
Pushing carefully, turn the counterweight (6) onto the rear end of the tonearm tube (9), so that the downforce
scale (6a) shows towards the front of the player. Lower the armlift and position the cartridge in the space
between arm rest and platter. Carefully rotate the counterweight (6) until the armtube balances out. The arm
should return to the balanced position if it is moved up or down. This adjustment must be done carefully. Do
not forget to remove the cartridge protection cap if fitted.
Once the arm is correctly balanced return it to the rest. Hold the counterweight (6) without moving it, and gently
revolve the downforce scale ring (6a) until the zero is in line with the anti-skating stub (15). Check whether the
arm still balances out.
Rotate the counterweight counter clockwise (seen from the front) to adjust the downforce according to the
cartridge manufacturer's recommendations. One mark on the scale represents 1 mN (= 0,1g / 0,1 Pond) of
downforce.
Please note: Adjust the downforce prior to installing the anti-skating weight.
The recommended downforce for the factory fitted Ortofon OM 10 cartridge is 15mN.
Anti-skating force adjustment
The anti-skating force must be adjusted corresponding to the downforce as follows:
Downforce Groove in the stub (15)
10 - 14mN 1st from bearing rings
15 - 19mN 2nd " " "
20mN and bigger 3rd " " "
Slip the loop of the anti-skating weight's thread over the second groove of the stub to set the correct anti-
skating force for the factory-fitted cartridge. Feed the thread through the loop of the wire support (17).
Fitting the lid
Fit the lid (dust cover 10) carefully over the hinge prongs and adjust the screws (12) until the lid stays open
where you want it to without being too stiff to open or close.

© Audio Trade GmbH · Pro-Ject Debut Carbon/Phono USB / Ortofon OM10 · Revision 2013.11.15 5
Connection to the amplifier
The record player has gold plated female RCA phono sockets (14) so you can substitute the interconnect cables
supplied with higher quality cables such as the P
Pro-Ject Connect it
interconnect cables for connection to the
amplifier if you wish. Use a line input (such as AUX, CD, Tuner, Tape or Video) on your amplifier.
!
Due to the built in phono pre-amplifier, a phono input (sometimes labelled gram, disc or RIAA) is not
suitable.
Take care to connect the left and right channels correctly. The right channel is usually marked red, the left
channel black or white. Check the manual supplied with your amplifier for relevant information. The earthing
wire of the tonearm lead should be connected to the earth terminal on your amplifier (if provided).
For detailed product information regarding Pro-Ject Audio interconnect cables please refer to the Pro-Ject
web site
www.project-audio.com.
The recommended load impedance for the factory fitted cartridges is:
47kohms/MM-input
The 3,5 mm connector (supplied) can be used to connect your Pro-Ject Debut Carbon/Phono USB to any line
level/auxiliary input (Computer, Midi System, Mixer etc.).
Connect the socket end to the phono plugs at the end of the audio trailing lead from your turntable and insert
the 3,5 mm plug into the relevant socket on your audio component.
Connecting to a Computer
Connect the USB-output of the unit to a free USB-socket on your computer and turn it on/make sure it is
powered on.
The “new hardware found assistant“ will automatically detect the unit and announces it as a M
Microphone USB
audio codec
. There is no need to install a driver manually.
After installation, one setting has to be done. For example - Windows 7®operating system:
ÆControl Panel ÆSound ÆRecording ÆM
Microphone USB Audio CODEC
ÆProperties Æ
Advanced: set to 2
2channel, 16 bit, 48000 Hz (DVD Quality)
Please note: Connection should be made to an USB-socket of your computer directly. Connecting to
USB-hubs or switches can cause problems.
Recording Programme
In case you do not have a recording programme installed on your computer, you may download one free from
the Internet. Recording programmes may be found by searching Google or Yahoo.
In the menu of the recording programme, source or input may have to be set to M
Microphone USB audio codec
.
Please be aware that downloads from the Internet are made entirely at your own risk. Under no
circumstances can we carry responsibility or provide support for third-party software products sourced
from the internet or for any damage or problems arising from the use thereof. All downloads should
be checked with an up-to-date anti-virus programme. License fees may be applicable.
Mains power connection
Connect the mains lead to the mains.
!
AC outlet voltages vary from country to country. Before connecting to the mains. Make sure that the
voltage in your area meets the voltage requirements printed on a label underneath the unit.
Useful tips
The record player should be positioned on a low-resonance surface such as wood or multiple layer ply board
to avoid structural vibrations disturbing replay.
Switching on and off
Pressing the power switch (19) alternately starts or stops the motor.

© Audio Trade GmbH · Pro-Ject Debut Carbon/Phono USB / Ortofon OM10 · Revision 2013.11.15
6
Changing replay speed
To play records at 45 r.p.m. first remove the platter (5). Using the accessory tool provided (3a), hook the belt
(3) over the larger diameter part of the motor pulley (2). Refit the platter. To revert to 33 r.p.m. repeat the
proceedings using the smaller step on the pulley.
Fitting and connecting the cartridge
** All cartridges with half inch mounting holes can be fitted. Leaving the needle's protection cover on, fit the
cartridge to the headshell using the screws supplied with the cartridge by passing one screw through each
slot in the headshell (20). Do not tighten the nuts yet.
Connect the tonearm wires to the cartridge pins as follows:
white left channel positive (L+)
red right channel pos. (R+)
green right channel return (R -)
blue left channel return (L -)
The full sound quality of the record player can only be achieved if the cartridge is correctly adjusted. Particular
tools like the Pro-Ject alignment tool are required to accomplish this job properly.
If you are not well acquainted with the adjustment of cartridges you are advised to call upon the willing help of
your Pro-Ject dealer to accomplish this task for you.
Please note: Adjusting a cartridge and tonearm calls for the greatest care in order to avoid damaging
the cartridge or tonearm bearings. Leave this work to your dealer if you are in any way unsure of the
necessary steps and precautions to be taken.
Adjusting the azimuth
** The cartridge needle must be vertical in the record groove in order to trace the
groove wall modulations correctly.
A small screw at the bearing end of the arm allows incorrect azimuth to be
corrected if your needle is not mounted exactly perpendicular to the cartridge body
(which is often the case).
Slacken off the screw just enough to be able to revolve the arm tube without
applying force. Please note: do not remove the screw completely!
Screw
With the aid of a good magnifying glass adjust the needle until it is vertical in the groove (i.e. perpendicular
to the record's surface). Ideally this should correspond to the top surface of the cartridge body being parallel
to the record surface.
When you are satisfied that the needle is vertical retighten the screw carefully.
Please note: Under no circumstances should the arm tube be adjusted with the needle still in the
record groove! Irreparable damage may be caused to the cantilever suspension! The arm must be
lifted to make each adjustment and lowered afterwards to check it.
Maintenance and cleaning
Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic
cloth. Never use a dry cloth because this will create static electricity which attract more dust! Antistatic
cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber
parts. It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage.
If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching.
!
Always disconnect the record player from the mains power supply as a precaution before maintenance!

© Audio Trade GmbH · Pro-Ject Debut Carbon/Phono USB / Ortofon OM10 · Revision 2013.11.15 7
Technical specifications Pro-Ject Debut Carbon Esprit / Pro-Ject 8.6cc
Nominal speeds 33/45 r.p.m.
Speed variance ±0,8%
Wow and flutter ±0,1%
Signal to noise 68dB
Effective tonearm mass 6g
Effective tonearm length 8,6 " ( 218,5mm)
Overhang 18,5mm
Power consumption 7,5W, 0W in Stand-By
Voltage suitable for your country's mains supply
Dimensions (W x H x D) 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm
Weight 6kg
Technical specifications moving magnet phono pre-amplifier - A/D converter
* typical for MM or high output MC cartridges
Input capacitance/input impedance 47kohms/100pF *
Gain 32dB
Output voltage typically 200mV/1kHz at 5mV
Noise floor -88dB
RIAA-equalisation curve accuracy 20Hz-20kHz / max. 0,5dB
USB output digital serial data protocol USB 1.1
Operating systems Windows XP®, Windows VISTA®, Windows 7®, Windows 8®,Mac OS
Technical specifications MM-Cartridge Ortofon OM 10
Frequency range 20-22.000Hz
Channel separation 22dB/1kHz
Output voltage 4mV
Recommended load impedance 47kohms/amplifier connection – MM-input
Compliance/stylus type 25m/mN – elliptical
Recommended tracking force 15mN
Weight 5g
Potential incorrect use and fault conditions
Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before
leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but
can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common
fault symptoms is included.
The platter doesn't turn although the unit is switched on:
The unit is not connected to the mains power supply.
No mains at the socket.
Drive belt is not fitted or has slipped off.
No signal through one or other channel or both channels:
No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or
from that to the phono box or between that and the amplifier. This could be due to a faulty plug,
broken wire or solder joint or simply loose plug/socket connection.
Wrong input selected at amplifier.
Amplifier not switched on.
Amplifier or speakers defective or muted.
No connection to the loudspeakers.
Distorted or inconsistent sound from one or both channels:
Record player is connected to wrong input of amplifier, or MM/MC switch incorrectly set.
Needle or cantilever damaged.
Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.

© Audio Trade GmbH · Pro-Ject Debut Carbon/Phono USB / Ortofon OM10 · Revision 2013.11.15
8
Service
Should you encounter a problem which you are not able to alleviate or identify despite the above information,
please contact your dealer for further advice. Only when the problem cannot be resolved there should the
unit be sent to the responsible distributor in your country.
Guarantee repairs will only be effected if the unit is returned correctly packaged. For this reason we recommend
keeping the original packaging.
Never return a record player without making sure that is it safely disassembled and correctly packaged in the
original packaging according to the diagrams on the last page of this user guide. Please remove these parts
and pack them separately: lid (10), counterweight (6), anti-skating weight (16) platter (5) and belt (3). Fit the
cartridge protection cap. Insert the transport lock for the tonearm (18) prior to carefully packaging the record
player.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions
for use and/or by transportation without the original packaging. Modification or change to any part
of the product by unauthorized persons release the manufacturer from any liability over and above
the lawful rights of the customer.
Copyright, trademarks
PRO-JECT is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Audio Trade GmbH
Copyright ©2012. All rights reserved.
The information was correct at the time of going to
press. The manufacturer reserves the right to make
changes to the technical specification without prior
notice as deemed necessary to uphold the ongoing
process of technical development.
Windows XP®, Windows Vista®, Windows 7®, Windows 8®are trademarks of the Microsoft group of companies.
Mac and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.

© Audio Trade GmbH · Pro-Ject Debut Carbon/Phono USB / Ortofon OM10 · Revision 2013.11.15 9
Tomearm
transport look
Lid
Platter
Accessories
Tonearm
counterweight

Product information
12. 2013
Update: JK / DZ Date: 12.12.2013
Debut Carbon Phono USB (DC)
Audiophile turntable for Hifi & Audio-Transfer to PC/Mac
x 8,6” carbon tonearm with pre-mounted OM10 cartridge
x Increased platter size with more weight & felt mat
x Precision belt drive with synchronous motor
x New DC power supply with ultra precision frequency DC-
driven AC generator (like Speed Box) for ultimate speed
stability
x New TPE motor suspension
x Integrated Phono-MM preamplifier
x Connections: line-level RCA to amp & USB to PC/Mac
(simultaneously)
x 7 high-gloss colours
Speed 33, 45 (manual speed change)
Drive principle belt drive
Platter 300mm metal with felt mat
Mains bearing stainless steel
Wow & flutter +/- 0,10%
Speed drift +/- 0,80%
Signal to noise - 68dB
Tonearm 8,6”, Carbon
Effective arm length 218,5 mm
Effective arm mass 6,0 g
Overhang 18,5mm
Tracking force 10 - 30mN
Included accessories 15 volt DC power supply, lid
Power connection 110/120 or 230/240 Volt - 50 or 60 Hz
Power consumption < 1 watt
Dimensions 415 x 118 x 320mm (WxHxD) lid closed
Weight 6 kg net
The best-buy turntable classic with carbon tonearm, computer connection and DC power supply!
The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc
and the assumed demise of vinyl records, an analogue product re-emerged in the “mass market” – something all music lovers could afford.
The new Debut Carbon Phono USB (DC) has been designed to set new standards in this category for the coming decade – perfectly timed as
analogue today is again a respected source, while the demand for good turntables is growing again!
The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted reso-
nance. This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower
price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound
quality is greatly improved. The approved belt drive offers low noise AC motor with effective motor decoupling (utilising TPE damping) and ultra
precision DC-driven AC frequency generator (like Speed Box) for ultimate speed stability without unwanted vibration.
Because Debut Carbon Phono USB (DC) comes with pre-mounted cartridge and built-in phono preamplifier with USB output, connection to both
line-level input of your hifi system and recording of vinyl to PC/Mac easily can be done simultaneously!
Debut Carbon Phono USB (DC) is offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option.
PRO-JECT AUDIO SYSTEMS
a division of AUDIO TUNING GmbH
1050 Wien, Margaretenstraße 98,
Debut Carbon Phono USB
(DC) / OM10
retail price
449,00 €
AD-converter with USB-Output