PRO Light ELUM120A User manual

Order codes: ELUM120A
Tour Batten TW
User Manual

www.prolight.co.uk Tour Batten TW User Manual
2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablemainssupplyvoltageis
between100~240VAC,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• Thislightingxtureisforprofessionaluseonly-itis
notdesignedfororsuitableforhouseholduse.The
productmustbeinstalledbyaqualiedtechnicianin
accordancewithlocalterritoryregulations.Thesafetyof
theinstallationistheresponsibilityoftheinstaller.The
xturepresentsrisksofsevereinjuryordeathduetore
hazards,electricshockandfalls.
• Warning!RiskGroup2LEDproductaccordingto
EN62471.Donotviewthelightoutputwithoptical
instrumentsoranydevicethatmayconcentratethebeam.
• WARRANTY:Twoyearsfromdateofpurchase.

www.prolight.co.uk Tour Batten TW User Manual
3
Product overview & technical specications
ThisTourBattenTWfeatures10x10WwarmwhiteLEDsandavariablecolourtemperaturebetween
1600K–2900K.ThetemperaturecanbesetviatherearmenuorDMX.Whendimmed,thexturecanemulatea
traditionalhalogenlampwithanorangeglowsimilartoasunstrip,whilstthe18°beamproducesasmoothwash
orblindereffect.
Tour Batten TW
Specications Tour Batten TW
Powerconsumption 110W
Powersupply 100~240V,50/60Hz
Dimensions 139x1082x130mm
Weight 6.5kg
Ordercode ELUM120A
1082mm 130mm
1000mm 78.2mm
1042mm
139mm
92.8mm
01-PowerindicatorLED
02-RDM/DMXindicatorLED
03-LCDdisplay
04-Functionbuttons
05-5-PinDMXinput
06-5-PinDMXoutput
07-PowerCONinput
08-PowerCONoutput
09-FuseT3.15A250V
10-Powerswitchon/off
Inthebox:1 x xture,
2 x end brackets,
1 x power cable
& 1 x user manual
RDM/DMX OUTPUT
POWER OUTPUT (15A Max.)
RDM/DMX INPUT
POWER INPUT (15A Max.)
100-240V~50/60Hz
MENU UP ENTER
RDM/DMX
POWER
DOWN
PRESS & HOLD “MENU” AND “ENTER” TO UNLOCK
1 = Ground
2 = Data -
3 = Data +
4 = NC
5 = NC
1 = Ground
2 = Data -
3 = Data +
4 = NC
5 = NC
POWER
FUSE:
T3.15A 250V
TOUR BATTEN TW
www.prolight.co.uk
CAUTION RISK OF ELECTRIC SHOCK
DO NOT OPEN THIS FIXTURE
WARNING: THIS PRODUCT MUST BE EARTHED
RDM/DMX OUTPUT
POWER OUTPUT (15A Max.)
RDM/DMX INPUT
POWER INPUT (15A Max.)
100-240V~50/60Hz
MENU UP ENTER
RDM/DMX
POWER
DOWN
PRESS & HOLD “MENU” AND “ENTER” TO UNLOCK
1 = Ground
2 = Data -
3 = Data +
4 = NC
5 = NC
1 = Ground
2 = Data -
3 = Data +
4 = NC
5 = NC
POWER
FUSE:
T3.15A 250V
TOUR BATTEN TW
www.prolight.co.uk
CAUTION RISK OF ELECTRIC SHOCK
DO NOT OPEN THIS FIXTURE
WARNING: THIS PRODUCT MUST BE EARTHED
RDM/DMX OUTPUT
POWER OUTPUT (15A Max.)
RDM/DMX INPUT
POWER INPUT (15A Max.)
100-240V~50/60Hz
MENU UP ENTER
RDM/DMX
POWER
DOWN
PRESS & HOLD “MENU” AND “ENTER” TO UNLOCK
1 = Ground
2 = Data -
3 = Data +
4 = NC
5 = NC
1 = Ground
2 = Data -
3 = Data +
4 = NC
5 = NC
POWER
FUSE:
T3.15A 250V
TOUR BATTEN TW
www.prolight.co.uk
CAUTION RISK OF ELECTRIC SHOCK
DO NOT OPEN THIS FIXTURE
WARNING: THIS PRODUCT MUST BE EARTHED
RDM/DMX OUTPUT
POWER OUTPUT (15A Max.)
RDM/DMX INPUT
POWER INPUT (15A Max.)
100-240V~50/60Hz
MENU UP ENTER
RDM/DMX
POWER
DOWN
PRESS & HOLD “MENU” AND “ENTER” TO UNLOCK
1 = Ground
2 = Data -
3 = Data +
4 = NC
5 = NC
1 = Ground
2 = Data -
3 = Data +
4 = NC
5 = NC
POWER
FUSE:
T3.15A 250V
TOUR BATTEN TW
www.prolight.co.uk
CAUTION RISK OF ELECTRIC SHOCK
DO NOT OPEN THIS FIXTURE
WARNING: THIS PRODUCT MUST BE EARTHED
RDM/DMX OUTPUT
POWER OUTPUT (15A Max.)
RDM/DMX INPUT
POWER INPUT (15A Max.)
100-240V~50/60Hz
MENU UP ENTER
RDM/DMX
POWER
DOWN
PRESS & HOLD “MENU” AND “ENTER” TO UNLOCK
1 = Ground
2 = Data -
3 = Data +
4 = NC
5 = NC
1 = Ground
2 = Data -
3 = Data +
4 = NC
5 = NC
POWER
FUSE:
T3.15A 250V
TOUR BATTEN TW
www.prolight.co.uk
CAUTION RISK OF ELECTRIC SHOCK
DO NOT OPEN THIS FIXTURE
WARNING: THIS PRODUCT MUST BE EARTHED
06 05
08
01
02
04
03
07
09
10
0m 1m 2m 3m 4m 5m
18° - Lux 2140 1731 769
20°
433 277
•2yearwarranty
•10x10WwarmwhiteLEDs
•Beamangle:18°
•1731Lux@2m
•Pixelmappingcapabilities
•DMXchannels:8bit-
1/2/5/10/6
•16bit-2/4/10/20
•Static,autorunandmaster/
slavemodes
•0-100%16bitdimming
•RDM(RemoteDevice
Management)
•4pushbuttonmenuwith
LCDdisplay
•PowerCONinput/output
•5-PinXLRinput/output
•Convectioncooled

www.prolight.co.uk Tour Batten TW User Manual
4
Operating instructions
Main Menu Sub Menu Options/Values Description
DMX
Channel
01/8Bit 1channelmode-8bit
DMXChannelSetting
02/16Bit 2channelmode-16bit
02/8Bit 2channelmode-8bit
04/16Bit 4channelmode-16bit
05/8Bit 5channelmode-8bit
10/16Bit 10channelmode-16bit
10/8Bit 10channelmode-8bit
20/16Bit 20channelmode-16bit
06/8Bit 6channelmode-8bit
Address 001-512 DMXAddressSetting
NoDMX
OFF
FunctionswhennoDMXsignalHold
Program
Glide ON SwitchingDMXfadetoonactivates
ashortdelayonDMXcommands
OFF
Chase
Program Program:01-Program:16/
Program:Auto/Program:Full Program
Master 000-100 Masterdimmer
Speed 01-100 ProgramSpeed
FadeTime 000-100 ProgramFade
IMPORTANT! PLEASE NOTE:TheLCDdisplayforthisxturehasamenulockingfunctionwhere
after30secondsofinactivityitwilllock.Tounlockthemenuholdthe“MENU”and“ENTER” buttons
for3seconds.

www.prolight.co.uk Tour Batten TW User Manual
5
DMX mode:
OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomes
tocustomisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthe
xtureandeachxtureindependently.
ToaccesstheDMXchannelmode,pressthe“MENU”buttononthefrontoftheunittoshow
“Address” ontheLCDdisplay.Pressthe“ENTER”buttontoshow“Channel” ontheLCDdisplay.
Nowusethe“UP”and“DOWN”buttonstochooseoneofthechannelmodes;
1/2/5/10/6-8bit,2/4/10/20-16bit(seechartonpage4).
Pressthe“ENTER”buttontoconrmthesetting.
ToaccesstheDMXaddressmode,pressthe“MENU”buttononthefrontoftheunittoshow
“Address” ontheLCDdisplay.Nowthe“UP”and“DOWN”buttonstosettherequiredDMXaddress.
Pressthe“ENTER”buttontoconrmthesetting.
ToaccesstheDMXbitsetting,pressthe“MENU”buttononthefrontoftheunittoshow
“Address” ontheLCDdisplay.Pressthe“ENTER”buttontoshow“Glide” onthe
LCDdisplay.Nowthe“UP”and“DOWN”buttonstosettheDMXfade“ON”or“OFF”.
Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MENU”button.
Operating instructions
Channel Value Function
1 000-255 LEDs1-10dimmer(0-100%)
1 channel mode - 8 bit:
Channel Value Function
1 000-255 LEDs1-5dimmer(0-100%)
2000-255 LEDs6-10dimmer(0-100%)
2 channel mode - 8 bit:
Channel Value Function
1 000-255 LEDs1-2dimmer(0-100%)
2000-255 LEDs3-4dimmer(0-100%)
3000-255 LEDs5-6dimmer(0-100%)
4 000-255 LEDs7-8dimmer(0-100%)
5 000-255 LEDs9-10dimmer(0-100%)
5 channel mode - 8 bit:
Channel Value Function
1high8byte
2low8byte
00000-
65535
LEDs1-10dimmer
(0-100%)
2 channel mode - 16 bit:
Channel Value Function
1high8byte
2low8byte
00000-
65535
LEDs1-5dimmer
(0-100%)
3high8byte
4low8byte
00000-
65535
LEDs6-10dimmer
(0-100%)
4 channel mode - 16 bit:
Channel Value Function
1high8byte
2low8byte
00000-
65535
LEDs1-2dimmer
(0-100%)
3high8byte
4low8byte
00000-
65535
LEDs3-4dimmer
(0-100%)
5high8byte
6low8byte
00000-
65535
LEDs5-6dimmer
(0-100%)
7high8byte
8low8byte
00000-
65535
LEDs7-8dimmer
(0-100%)
9high8byte
10low8byte
00000-
65535
LEDs9-10dimmer
(0-100%)
10 channel mode - 16 bit: