Pro-Line Boats 24 Super Sport User manual

Owner’s Manual
Pro-Line
24 Sport / 25 Sport
Copyright 1996-99 Pro-Line Boats Inc., P.O. box 1348,
Crystal River, FL 34423. All rights reserved. Rev. 07-06-04
Specifications subject to change without notice. Actual boats may vary from drawings.

Table of Contents
I. Introduction
Dealer / Customer responsibilities
Registration
Insurance
II. Safety
Regulations
Equipment
Passenger safety
Rules of the road
Hazardous conditions
Alcohol
Carbon monoxide
Fire
Flooding
III. Controls
Ignition
Choke
Lanyard Stop Switch
Shift / Throttle / Trim
Steering
Instruments
Switches
IV. Systems
Fresh Water
Sea Water
Fuel / Oil
Head / Waste
Electrical
After Market Accessories
V. Trailering and Launching
Capacity
Hitch
Load Distribution
Launching and Retrieving
VI. Operation and Performance
Loading
Fueling
Starting
Trim / Tilt
Prop
VII. Service and Care
Fiberglass / Gel coat
Marine growth
Windshield / Acrylics

Stainless Steel / Aluminum
Canvas
Upholstery
Corrosion Protection
Winterization and Storage
VIII. Appendix
Boat Identification Information
Trouble Shooting Chart
Nautical Terms
Specifications

Introduction
Congratulations! You are now the proud owner of a new Pro-Line 24/25 Sport fishing
boat.
Welcome into the proud family of satisfied Pro-Line owners. Every expedition lets you
enjoy the outstanding features designed into every boat we construct. Your new Pro-Line
is more than just a boat, it's a lifestyle.
Pro-Line's commitment to the needs and wishes of the professional sport fisherman has
resulted in a superior fishing craft, providing you with comfort, performance, security
and fishability. All of our boats comply with U.S. Coast Guard (USCG) safety
regulations, and are designed and crafted in accordance with the National Marine
Manufacturers Association (NMMA), American Boat and Yacht Council (ABYC)
standards, and the optional Common European directive (CE).
This manual (to be kept onboard your Pro-Line) is designed to provide you with
information necessary for safe, efficient operation and care of your new Pro-Line. Take
the time now to carefully review the information in your owner’s pack and this manual to
maximize your enjoyment and safety as well as familiarize yourself with your new boat.
Dealer's Duties
Your dealer's responsibilities include but are not limited to:
* Pre-delivery verification of proper rigging and operation.
* Providing adequate orientation in general operation of your Pro-Line including
explanation of specific safety considerations regarding the use of systems and
components.
* An explanation of owner’s packet literature and warranty registration
cards for all separately warranted equipment and accessories.
* Explaining local and out of area service procedures during and after
warranty periods.
Customer Responsibilities
* Be proficient in boat handling and safety. THIS MANUAL IS NOT
INTENDED TO PROVIDE COMPLETE TRAINING ON ALL ASPECTS
OF GENERAL BOAT OPERATION.
* Read and understand the limited warranty.
* Read all literature and instructions as well as use and maintain all equipment as
directed.
* Examine the boat at time of delivery to insure that all systems are
functioning properly.
* Learn about and operate boat in accordance with local, state, and federal laws,
regulations, and registration requirements.
* The owner is legally responsible for all liabilities of operation. Secure
insurance protection.

Safety
Your Pro-Line boat has been constructed with safety in mind. However, the ultimate
safety of you and your passengers is in your hands. Plan your trips carefully. Insure
ample fuel supply and a reserve. Tell someone where you are going and when you
expect to return. Keep current charts onboard. Read USCG boating safety circulars and
follow the safety guidelines.
Regulations
The USCG is the authority of all waterways. State boating regulations are enforced by
local authorities. You are subject to marine traffic laws and "Rules of the Road" for both
federal and state waterways. Therefore, you must submit to boarding if requested by
proper authority. There are many publications available from the Coast Guard
concerning regulations. Call the Boating Safety Hot Line at (800)-368-5647 for
additional information.
Equipment
USCG regulations require the following equipment while operating your boat:
* Fire extinguisher
* Personal Flotation Device (PFD) for each occupant
* One throwable PFD
* Sound signal device
* Navigational lights if operated at night
* Sight signal (flare - night, orange flag - day) when in coastal waters or great
lakes.
* Anchor and sufficient line
In addition, here is a list of suggested equipment you should have aboard your Pro-Line:
* First aid kit and blankets * Sea anchor with line
* Mooring lines and fenders * Bailing device
* Combination oar / boat hook * Tool kit and lubricant
* Spare prop and hardware * Spare fasteners, hose clamps, and plugs
* Spare fuses and bulbs * Binoculars
* Local charts and compass * Water proof flashlight
* 2 way radio * EPIRB (emergency beacon)
* Floating key chain and spare keys * Navigation device
* Emergency food and water * Water proof matches or lighter
Passenger Safety
You are responsible for the safety and conduct of your passengers. Make sure that:
* You instruct passengers on proper use and location of PFD's. Children
and non-swimmers should wear one at all times.
* Each passenger is in a safe location when underway and knows to keep
the boat balanced.
* At least one other person knows how to operate the boat in case of emergency.
* They are aware of prop dangers and the possibility of sudden maneuvers and
jolts.
* The engine is turned off and the key is removed when swimmers are near the

prop or using the dive platform.
* All keep away from lines under stress should they break and recoil.
Rules of the Road
Know and use the rules of the road. The information here is only a brief overview.
Contact the USCG for detailed information.
Audible warning signals:
* One short horn blast: starboard course change.
* Two short horn blasts: port course change.
* Three short horn blasts: astern operation.
* Five horn blasts: doubt about previous signal, or danger.
* One Five second horn blast every minute: for fog operation
When overtaking, give-way vessel announces intention with horn blast(s) and waits for a
response, then completes maneuver.
When approaching head-on, both boats give way after giving appropriate horn blast(s)
(preferably to starboard).
When crossing, a vessel converging from starboard has the right-of-way. Port vessel
gives way (both acknowledge with one short horn blast).
Know and observe navigational buoys and markers.
Give way to craft under sail.
Hazardous Conditions
Keep track of weather developments and avoid hazardous conditions if possible. When
forced to operate your Pro-Line in storm conditions:
* Wear PFD's
* Stow loose gear and equipment.
* Place heavy items as low as possible.
* Head for the easiest to reach safe location.
* Reduce speed. You are moving too fast if the boat leaves the water.
* If power fails, rig a sea anchor off the bow (an empty ice chest in a pinch).
* Stay with the boat if it capsizes unless it is burning out of control.
Alcohol
Don't drink and drive. If you have been drinking, have a designated driver who has not
been drinking. Never operate a boat under the influence of drugs or alcohol.
Carbon Monoxide
Be aware of and avoid conditions that can cause carbon monoxide poisoning (see USCG
boating safety circular 77). Sources of carbon monoxide include any gas or diesel
engine, any flame such as a charcoal grill, stove, or heater. Carbon monoxide can
accumulate to deadly levels in enclosed spaces. Always ventilate occupied areas of
vessel with fresh clean air.
Fire
Be aware of and avoid conditions that can lead to accidental fire. Guard against and
watch for fuel spills and leaks. Inspect wiring for damage or exposure that could lead to
short circuits or arcing. Make sure those who smoke are careful to avoid accidental fire
ignition. Don't allow smoking while fueling. Keep a USCG approved fire extinguisher
on board at all times. Inspect the fire extinguisher regularly and learn how to properly
use it (instruct others as well). Use water to fight a fire as a last resort after making

arrangements to abandon the boat if a fire should get out of control. Keep the following
in mind if a fire is burning out of control and you must abandon the boat:
* Abandon the boat into the wind to minimize burn risk from floating fuel.
* Wear a PFD unless you must swim under burning fuel.
* If swimming under burning fuel, throw a PFD outside of the burning area and
swim under the burning fuel to it.
Flooding
Be aware of and avoid conditions that can cause your boat to flood with water.
Possible causes of flooding include: damage to hull or thru-hull fitting, waves washing
into the boat, water entering cockpit due to improper loading, or failure to properly install
drain plug. The boat will become flooded and may swamp, capsize, or sink if water
enters the boat faster than the bilge pump can expel it.
Controls
Pro-Line Boats offers many different motor choices. Therefore, the information in this
manual is general in regard to engines and controls. Refer to the engine manual in your
owner’s packet for additional specific information.
Ignition
The ignition switch has three positions: “OFF”, “ON”, and “START”. To start the
engine: attach safety lanyard and turn the key clockwise against the spring pressure to the
start position. Once the engine starts, release clockwise pressure allowing spring tension
to return switch to the “ON” position. Some engine models incorporate the choke into
the ignition key switch. See the engine manual for specific details.
Choke
The choke is only used to aid in starting a cold engine. Choke operation varies with
manufacturer. Consult your engine manual.
Lanyard Stop Switch
The safety Lanyard Stop Switch shuts off the engine in case the operator is thrown from
the boat. Always attach the lanyard securely to the operator to insure proper functioning.
Shift/ Throttle/ Trim
Your Pro-Line can be ordered with different shift / throttle systems. Refer to the owner's
packet to find the manual pertaining to your particular installation. Separate shift and
throttle controls are available for each outboard motor. The throttle lever has three range
positions: “Forward”, “Neutral”, and “Reverse”. The shift function occurs in the first
portion of the lever travel. After the transmission is shifted into gear, further movement
of the lever advances the throttle. Push the throttle lever ahead to move forward and pull
it back for reverse. Centralize the lever to the detent for neutral. The throttle lever is
equipped with a neutral safety switch to prevent the motor from starting in gear. Practice
shifting a few times without the engine running to develop a feel for the range and
friction of the system. The initial short movement of the lever to engage the transmission
should be made firmly to avoid causing gear clash. CAUTION: Use care in shifting to
avoid advancing the throttle more than intended. Practice in a safe area away from
obstacles until familiar with the feel of the throttle. The throttle can be operated
independent of the transmission for starting. If attempting to start an engine this way,

keep a hand on the throttle to pull it back as the engine clears to prevent over revving.
The shift levers can be operated independently for precise maneuvering (twin engines at
slow speed only). Refer to the engine / drive manuals in your owner’s packet for specific
information.
Compass, Dash Glove / Radio Box
Key Switch, Steering Wheel, Trim Tab Switches, Binnacle, Cup Holders
Steering
Your Pro-Line is equipped with a self contained hydraulic steering system. When the
steering wheel is turned, the helm pump pumps fluid to the steering cylinder causing it to
extend or retract. Periodically check the fluid level and fill if necessary. Beware of
adding too much fluid, especially if the ambient temperature is cold because subsequent
expansion could cause leaking or damage to your system (refer to manual in packet).
Every 24 hours of operation check all nuts, caps, and hose fittings for tightness. Make
sure the hoses are not chafing, or kinking on sharp corners. Also, check that hose ends
are not damaged or distorted. The fluid should be changed annually under normal
conditions and every six months during times of heavy usage. If your steering does not
operate properly, first check for: drive entanglements, fluid level, hoses / fittings for
leaks, and / or air in the system.

Instruments
Your Pro-Line's instrumentation will vary from model to model and engine to engine.
Therefore, the following descriptions are general. Refer to your engine manual for
specifics.
Fuel Gauge
Differences in temperature, humidity, speed, and trim can affect the actual accuracy of
this gauge in service. It is important to verify the fuel flow in gal./hr. for your boat and
make note of your gauge position with respect to time for different RPM settings. No
gauge can give 100% accuracy. If you notice unusually high or low fuel consumption,
investigate further to see if the engine is using more fuel than normal or the gauge has
failed.
Temperature
The temperature gauge indicates the internal temperature of your engine. Your engine is
equipped with a thermostat to quickly bring the engine up to its optimum operating
temperature range. Outboard engines are also equipped with an audio alarm system
indicating an overheat condition. Many times over heating may occur due to a blockage
of the water intakes caused by aquatic vegetation or mud. Check the water intakes for
blockage and see the engine manual for specific details.
Volt
The volt meter indicates battery voltage. A low reading indicates too heavy of a load or a
malfunction in the charging system. Too high of a voltage indicates a fault in the
charging circuitry and continued operation will damage the battery. Refer to engine
manual for specifications.
Tachometer
The tachometer indicates the revolutions per minute (RPM) of your engine. Do not
operate the engine beyond the limits stated in your engine manual. Abnormally low
tachometer readings (for a given throttle setting) indicates loss of power, or a prop
entangled with weeds or trash. Check the prop first. A reading higher than normal may
indicate a ventilating or cavitating prop as well as possible prop/drive damage.
Speedometer
The speedometer indicates the speed of your boat in Miles Per Hour (MPH) and
Kilometers Per Hour (Km/H). The gauge operates by sensing water impact pressure from
the pitot tube which is mounted on the transom (or integrated into the lower drive unit of
the motor) depending upon the motor manufacture. Suspect a blocked pickup if the
gauge fails to give a reading.

Trim
The trim gauge indicates the in (down) and out (up) position of the drive unit in relation
to the hull.
Options
Optional instrumentation for your Pro-Line includes: fish locator / depth finder, VHF
radio, GPS navigation aids, etc.. Refer to the manuals supplied.
Switches
Back View of Switch Panel (wiring)
Front View of Switch Panel

BilgePump
Your 24/25 Sport is equipped with an automatic bilge pump that has a manual switch
override. The pump is located at the aft end of the bilge at the keel. The automatic float
switch is wired directly to the battery terminal through an inline fuse. Keep the bilge area
clean and free from debris that could clog ports or inhibit float movement. The helm
switch overrides normal automatic operation. A circuit breaker for the pump is located at
the helm below the switch. Keep the battery that provides power to the bilge pump
charged. If the battery is discharged and flooding occurs, the boat could swamp causing
damage and possible loss of life or property.
Lights
Your Pro-Line is equipped with a variety of different lighting systems. The navigation
and anchor lights are required to be used for operation at night or under low visibility
conditions to indicate your position to other boaters. Visually verify operation of your
Nav/Anc lights and insure the lights are free from obstructions. The dash instrument
lights are turned on by the Nav/Anc light switch as well. Lights are also provided for the
cockpit, baitwell, console compartment, helm-courtesy with optional t-top, and optional
spreader lights. Spreader lights are operated by a switch incorporated into the helm-
courtesy light which is located on the t-top. An optional remote spot light is also
available and has a separate switch and control.
Accessory
These switches can be used for additional dealer installed accessories.
Windlass
The optional windlass is operated by a separate switch and is protected by an 80A
breaker located below the switch. Refer to the windlass manual for operation and
maintenance.
Trim Tabs
The optional trim tabs operate independently up or down to correct for differing
conditions of wind or load. Refer to the owner’s packet for specific information. The
trim tab pump is located on the side of the aft port stringer near the transom. The pump is
accessible through the port side transom / bilge hatch and should be maintained in
accordance with the manufacturer’s instructions.
Before the boat is underway, depress the bottom half of both switches until the tabs are
fully elevated (bow up position). While underway and in open water clear of other
boaters, depress the top half of the switches in half-second increments to achieve the
desired degree of trim. To correct a starboard list, depress the top half of the port switch
in small increments until the list is corrected. To avoid over trim, allow a few seconds
between tab adjustments to allow the boat to respond (if you over trim simply give the
over trimmed tab an adjustment in the opposite direction). Push the top half of both
rocker switches in half-second increments to trim the bow down.
Warning: trim tabs can cause a dramatic change in the attitude and heading of
your boat. Adjust them in small increments when in open water and clear of any
obstructions.

Trim Tabs

Circuit Breakers
The wiring on your 24/25 Sport is protected by circuit breakers and/or fuses. In the event
a device stops working, check to see if the circuit breaker is tripped or the fuse is blown.
The main breaker is located on the aft port side stringer and is accessible from the port
transom / bilge hatch. Additional breakers / fuses for the bilge pump, trim tabs, etc. are
located next to the main breaker and on the dash panel. A tripped breaker will protrude
from its set position indicating that the circuit has been overloaded. Turn off the
device(s) on the circuit then reset the breaker by pushing in once. If the breaker does not
reset or if it resets and then trips again after the device is turned back on, then a short
circuit exists or your device may be damaged, overloaded, or faulty. Correct the problem
and then reset the breaker. If the breaker continues to trip and you are certain the device,
switch, and wiring are in good repair; then either the breaker is too small for the load, or
is faulty. Reduce the load or replace the breaker.
Horn
The horn is used to signal, warn, or alert other boats or people on shore. Avoid any horn
use without appropriate purpose.
Baitwell and Washdown
These switches energize the sea water pumps (see Sea Water Systems section). Leave
these switches off when not in use.
Fish Box Pump
This switch operates the pump to drain the fish boxes and should be left off when not in
use.
Fresh Water
The fresh water switch activates the fresh water pump system (see Fresh Water Systems
section). The switch should be left off when not in use.

Systems
Fresh Water System
The optional fresh water pump on your Pro-Line supplies water on demand when a drop
in water pressure activates the pressure switch. The manual switch located at the helm
energizes the pump. The switch should be kept off while not in use. Do not run the
pump dry. The fresh water tank supplies the transom shower. The tank and pump are
both accessible for maintenance or repair via the access hatch located in front of the
console. The fresh water tank fill is located on the forward starboard gunwale by the
casting deck.
Console Front
Casting Deck Fill Hose Tank Pump Hoses
Fresh Water System

Sea Water Systems
The baitwell switch controls a pump mounted on a seacock in the bilge. An overflow
tube is provided that is inserted into the drain to allow circulation to keep bait alive. The
washdown pump is mounted in the bilge on the aft face of the aft fuel tank bulkhead.
The pump is equipped with a pressure switch. Turn the main switches off if the pumps
are not going to be used soon. Sea water is taken in through a “T” fitting on the seacock
and a strainer on the pump filters the sea water. The filter must be cleaned as needed to
avoid pump damage. The seacock should be closed when not in use.
Raw Water Filter, Seacock (shown in open position), On-demand Pump
Bilge Layout
Fuel / Oil System
The fuel tank on your Pro-Line is made of heavy gauge aluminum with internal baffling
to minimize sloshing. The tank is vented overboard and the vent should be inspected for
obstructions regularly. Deck plate access ports are placed over the hose connections and
the sending unit. Inspect the hose connections on a regular basis. There may be a leak
somewhere in the fuel system if you notice a fuel odor or see fuel in the bilge. Correct
any fuel leaks before operating the vessel.
Fuel filter / water separator unit(s) are located in the starboard bilge area. There is one
unit for each motor and the spin on cartridges should be renewed every season at a
minimum. Fuel tanks that are not kept full accumulate water faster due to condensation.
The cartridge(s) may need to be replaced more often depending upon usage and
conditions or if motors begin to run rough. When replacing the filters / separators, coat
the rubber seal with a film of grease or oil to help prevent sticking.
A primer bulb is used to prime the engine fuel pump with fuel. There is a primer bulb for
each engine. Squeeze the bulb a few times until resistance is felt in order to prime. If no
resistance develops and the fuel pump will not prime, you may be out of fuel, the primer

bulb may be defective, or a leak may have developed allowing air into the system.
Pro-Line boats equipped with oil injected outboard engines have remote oil tanks located
in the aft end of the bilge. The oil tank fill is located just above the motor well on the
starboard side. Insure that the tanks are well stocked with the recommended two stroke
oil - refer to your engine manual. It is imperative the oil supply remain clean and
uncontaminated by water or dirt. Check to make sure the oil lines are free from leaks,
kinks, and chafing. Some motors use a primer bulb to initiate oil flow. Sometimes air
may enter the system and require purging. Refer to your engine manual for specific
instructions.
Fuel / Oil System

Head / Waste
The head / console compartment door is secured in the closed position with draw latches.
Secure the door before operating the boat and make certain that no one is in the head
compartment when latching the door closed. Your Pro-Line is equipped with a portable
head. Refer to the manual supplied in your owner's packet. It is illegal to dump waste
overboard in most locations. Be sure to check the law in your area.
View of Porta-Potty through console head door
CenterConsole Head Compartment

Electrical
Direct Current
12 volt direct current provides electrical power for all lighting, pumps, electronics, and
D/C devices. A main breaker panel is located behind the port transom hatch. Optional
battery selector switches in the bilge are for battery isolation, parallel operation, and
disconnect. The main helm terminal panel is accessed by removing the panel above the
helm foot rest.
Caution: To avoid possible alternator / battery damage on twin engine installations,
insure that the optional dual battery switches are never left so both engines are connected
together (never leave a switch on “BOTH”). The preferred switch position is port engine
to port battery, starboard to starboard.
Please refer to Battery Switch Page in your manual to see proper
positioning of Battery Switches.

After Market Accessories
Your Pro-Line's electrical system was designed for factory tested and approved dealer
installed optional accessories. Pro-Line makes no recommendations to the suitability of
accessories that are not listed in the Pro-Line sales literature. Any unapproved
modifications or additions to the standard or optional system are done at the owner’s risk
and may void the warranty. Unapproved modifications could cause risk of fire or failure
of the electrical system. A pull wire is installed in the optional t-top to facilitate
installation of electronics. The wire is located on the starboard side, forward corner of
the overhead electronics box. Use the factory supplied buss bar for connections. Make
sure the circuit is protected by fuse or breaker and the wire is properly sized for the load
and length of run.
Trailering and Launching
Consult your trailer manufacturer for specific information relating to your particular
trailer. Pro-Line does not make or recommend the use of any particular trailer. Make
sure the trailer you use is certified. Consult your state authority for state regulations
pertaining to trailering a boat.
Use the following towing check list as a guideline:
* Check brakes if equipped.
* Check springs and under carriage for cracks, loose parts, and fasteners.
* Insure tires are inflated to proper pressure and in good condition.
* Check wheel bearings and lug nuts.
* Verify light and signal operation.
* Make sure boat is tied down from bow and stern eyes.
* Stow Bimini top and all items likely to blow off or out of the boat.
* Carry a spare tire and tools for changing (spare bearing and race set for
long trips).
* Securely brace O/B motors.
* Go slow over bumps.
* Check tires and hubs often for excessive heat. Service if required.
* Have an assistant watch blind spots and guide with signals when backing.
Capacity
The trailer you choose should be a proper match for your boat with regard to capacity and
hull design. Consult your dealer when making your selection. The tow vehicle must
have sufficient towing capacity for the combined load of boat, trailer and accessories.
Check the certification label on the forward port (left) side of your trailer to insure it has
adequate gross vehicle weight rating (GVWR) for the combined boat and trailer. The
boat weight must include the weight of the empty basic hull, motors, full fuel and fresh
water capacities, accessories, equipment, and provisions.

Hitch
Insure the hitch on the tow vehicle is rated for the gross total weight (GTW) or greater,
and the ball size matches the trailer receiver.
Load Distribution
In general, the tongue weight should be from 5 to 10 % of the GVWR. Make certain the
hull is evenly supported along the length and width of the trailer with no load
concentrations. The bottom of the transom should be supported and not hanging past the
end of the trailer. The bow must be supported as well. Load the boat so it is centered
side to side, and straight on the supports. Rollers, if used, should only serve to guide the
boat into position while in the water and not relied upon to support the weight of the boat.
The improper use of rollers voids your warranty and could seriously damage your hull.
Launching and Retrieving
Pre - Launch Check List:
* Install drain plug.
* Remove covers and tie downs (leave bow winch strap in place).
* Place lines and fenders if needed.
* Disconnect lights to avoid shorting.
* Verify safety equipment is aboard.
Launching:
* If possible use a lookout.
* Back down the ramp until wheels are underwater or the stern of the boat just
starts to float ( keeping perpendicular to the shore).
* Loosen bow strap, board the boat, and lower the motor.
* Start the motors and check the bilge for leaks.
* Remove winch strap from bow eye.
* Back boat off trailer.
* Dock the boat and park the tow vehicle.
Retrieving:
* Back down the ramp so trailer is half submerged.
* Carefully line up boat, slowly maneuvering with short bursts of power.
* When the keel is centered and boat is just touching the trailer, winch or
smoothly apply power until the boat eases to the bow rest.
* Secure the bow strap.
* Haul the boat out of the water and park out of the way of others.
* Remove the drain plug.
* Rinse off salt water as soon as fresh water is available.
* Stow equipment and canvas as well as affix tie downs and covers.
* Hook up trailer lights and verify operation.