PRO SIGNAL PS-ATWB47T User manual

Tilting Wall Mount
100x100/200x100
200x200/400x200
400x400
PS- ATWB47T
47"
MAX
CAU TI O N : DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
45kg
(99lbs)
MAX
INSTALLATION INSTRUCTIONS

2
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If
any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
M4x14 (x4)
M-A
M6x14 (x4)
M-E
Package W
ST6.3x55 (x4)
W-A
concrete anchor (x4)
W-B
D6 washer (x4)
W-C
M4x25 (x4)
M-B
M5x25 (x4)
M-D
M6x25 (x4)
M-F
M5x14 (x4)
M-C
M8x15 (x4)
M-G
1
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experiences and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• Never exceed the maximum load capacity.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. Use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
ø14xø6x10 (x4)
M-J
washer
M-I
(x4)
wall plate
A
(x1)
safety bar
D
(x1)
M8x30 (x4)
M-H
5mm allen key
E
(x1)
ø15xø8x15 (x4)
M-K
right adapter bracket (x1)
C
left adapter bracket (x1)
B
right decorative cover (x1)
G
left decorative cover (x1)
F
ST2.9x8 (x4)
M-L

4
3
WARNING
• Make sure that mounting screws are anchored into the center of the studs. Use of a stud finder
is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installer must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
1. Installing Decorative Covers 2b. Solid Brick and Concrete Block Mounting:
55mm/2.2" ø 4.5mm
ø 3/16"
2
1
Drill pilot holes
3
2a. Wood Stud Wall Mounting
Screw the wall
plate onto
the wall
X X
√
With the up arrow of the plate upward.
M-L
W-C
• When installing wall mounts on cinder block, verify the actual concrete thickness is at least
1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block.
It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Installer must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
WARNING
60mm/2.4" ø 10mm
ø 3/8"
Screw the wall
plate onto
the wall
X X
√
Drill pilot holes
1
2
With the up arrow of the plate upward.
W-C
W-A
W-B
W-A

65
3. Installing Adapter Brackets
TV
TV
TV
Tighten all screws but do not over tighten.
3-1 For Flat Back Screen
M-A M-C/M-E/M-G/
M-I
3-2 For Recessed Back Screen or to Access A/V Inputs
TV
TV
TV
Tighten all screws but do not over tighten.
· Position the adapter brackets as close as possible to the middle of the screen.
· Screw the adapter brackets onto the TV.
or
M-H
M-I
M-K
M-B M-D/M-F/
M-I
M-J

8
7
4. Hang TV onto the Wall Plate
wall wall
Two qualified
persons are
required
Hook the TV over the top of the wall plate.
Important: Make sure the TV is correctly hooked before releasing the TV.
Insert the safety bar at the bottom of the mount to
prevent the TV from being knocked off accidentally.
A padlock can be used in the safety bar to help
prevent theft of your TV.
Note: the padlock is not included.
5. Pitching Angle Adjustment
You can slightly adjust level for the display by tightening or loosening screws using a 5mm Allen key.
wall wall
E
-15° +10°
Push or pull from the top or bottom of the display to the desired angle.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.

10
9

X-ON Electronics
Largest Supplier of Electrical and Electronic Components
Click to view similar products for Pro Signal manufacturer:
Other Similar products are found below :
ABS-210-135-RC KVM-404 JR9502/5M JR8030/25M APFLY5 MJ-2325 ABM-713-RC PSG-BB-170W-2BP PSG01592 PSG01540
PSG01522 PS11169 PS11067 PS11360 PS11155 PS11153 PS11026 PSG03905 ABI-052-RC PSG03109 PSG03489 JR9505/1M
JR8052/20M MP-012LN APFLY2 SPC22887 PSG90335 PSG01495 PS11386 PS11185 PS11453 PS11172 ABS-244-RC PS000101
SVC683-3M AV02562 PSG02580 PSG01516 PS11028 PS11170 PS11156 PS11060 SPC23060 PSG90864 ABT-462-RC PS11092
JR9901/2M JR9755-10M BLACK CAB JR8052/7M CL62002X