PRO SIGNAL PS-MTSTWS28B User manual

Mobile TV Stand Trolley with Shelf
CAUTION: DO NOT EXCEED
RATED LISTED WEIGHT. SERIOUS
INJURY OR PROPERTY DAMAGE
MAY OCCUR!
INSTALLATION MANUAL
8. Adjustment
Maintenance
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please contact your distributor if you have any questions.
Adjust the display to the desired location
then tighten the knobs.
7. Hanging the Display onto the Universal Plate
TV Stand
200x200
300x300
400x200
400x400
600x400
PS -MTSTWS28B
70"
MAX 50kg
(110lbs)
RATED
50kg
(110lbs)
RATED
TVTV DVDDVD
10kg
(22lbs)
RATED
10kg
(22lbs)
RATED
Tighten the two screws by
using a proper screwdriver to
secure the adapter brackets
to the universal plate.
+10°
-10°
CAMERACAMERA
5kg
(11lbs)
RATED
5kg
(11lbs)
RATED

WARNING
21
Package M
NOTE: Read the entire instruction manual before you start installation and assembly.
Package
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
column 2
H
(x ) universal plate (x1)
I
left shelf
support (x1)
K
right shelf
support (x1)
L
DVD/AV components shelf 1
J
(x ) camera shelf
M
(x1)
D6
washer (x8)
P-G
wrench
P-J
8mm
Allen key (x1)
P-L
5mm
Allen key (x1)
P-K
M8
P-H
(x12) M6
-I
(x4)
P
M6x10
-A
(x4)
P
M5x8
-B
(x2)
P
M8x65
-C
(x12)
P
M10x35
-D
(x2)
P
D10
washer (x2)
P-E
D8
washer (x4)
P-F
connecting plate
N
(x1) right adapter bracket
O
(x1) left adapter bracket
P
(x1) plastic stopper
Q
(x2)
Component Checklist
IMPORTANT: Ensure you have received all parts against the component checklist prior to installation.
If any parts are missing or faulty, contact your destributor for a replacement.
base 1
C
(x )
plastic cover
D
(x2) caster with brake
G
(x2)caster
F
(x2)washer 4
E
(x )
short support leg 2
A
(x ) long support leg
B
(x2)
washer
M-F
(x4) big spacer
M-H
(x8)
small spacer
M-G
(x8)
M6x30
M-C
(x4)
M6x14
M-B
(x4) M8x30
M-D
(x4)
M5x14
M-A
(x4)
M8x50
M-E
(x4)

4
3
2.Installing the columns
1.Installing the Base Assembly
Insert the casters into the holes and tighten the casters
to secure.
Note: Make sure all casters are at the same height.
Note: Lock the brakes on the casters to avoid any sudden
movements during installation.
Attach the universal plate to the columns using the
appropriate screws,washers and nuts.
3.Installing the Universal Plate
F
G
AB
C
D
-C x8P
E
-H x8P P-J
H
I
P-K
P-C x4
P-F x4
-H x4P
P-D x2
P-E x2
P-L
G
F
Attach the support legs to the base
using the appropriate screws, washers
and nuts.
P-K
Snap the plastic covers onto the base.
Attach the columns to the base using the appropriate
screws and washers, then tighten all screws with the
Allen key.
Tighten all screws but do not over tighten.
Tighten all screws but do not over tighten.
Tighten all screws but do not over tighten.
Note: Each caster can be adjusted independently
for fine tuning. Slightly turn the nut to lower or
raise the base.
P-J

5
4. Installing the Camera Shelf
5. Installing the DVD/AV Components Shelf
· Attach the shelf supports onto the DVD/AV
components shelf.
· Hook the DVD/AV components shelf onto the
columns assembly.
· Attach the camera shelf to the connecting plate using the
screws.
· Attach the assembled camera shelf to the universal plate
using the appropriate screws, washers and nuts.
P-G x8
-KP
M
N
P-B x2
-KP
P-A x4
-I x4P
Tighten all screws but do not over tighten.
J
K
L
Q
Attach the plastic stoppers
to the DVD/AV components
shelf to prevent the shelf
from falling off unexpectedly.
6. Installing the Adapter Brackets
Tighten all screws but do not over tighten.
· Position the adapter brackets as close as possible to the center of the displays.
· Screw the adapter brackets onto the displays.
6a. For Flat Back Screens
6b. For Bump-out or Recessed Back Screens
TV
TV
TV
TV
TV
TV
Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screens.
P O
M-F
M-A
M-B
M-F
M-C
M-D
M-G
or
M-F
M-C
M-D
M-H
M-F
M-C
M-D
M-G
or
M-H
M-F
M-E
or
M-H
M-F
M-E
or
M-H
M-G
M-F
M-E
M-H
M-G
6