Prochem POWERMATE AC1204 Instruction Manual

AC1204 Powermate Manual 10/01/18 Page 1 of 18
SAFETY, OPERATION & MAINTENANCE
INSTRUCTIONS
POWERMATE AC1204
•CAUTION-READ THE INSTRUCTION MANUAL BEFORE USING THE APPLIANCE.
•ORIGINAL INSTRUCTIONS
•
MANUAL ALSO AVAILABLE ON-LINE AT WWW.PROCHEM.CO.UK

AC1204 Powermate Manual 10/01/18 Page 2 of 18
MACHINE DATA
MODEL NO.
AC1204
SERIAL NO.
DATE OF PURCHASE
DISTRIBUTOR NAME
DISTRIBUTOR TEL NO.
MANUFACTURER CONTACT
Prochem Europe Ltd.
Oakcroft Road,
Chessington,
Surrey KT9 1RH, UK
Telephone: + 44 (0)20 8974 1515
Fax: + 44 (0)20 8974 1511
Email: [e-mail]
Website: www.prochem-uk.com
All information and specifications in this manual are current at the date of issue. However, because of
Prochem Europe’s policy of continual product improvement, we reserve the right to make changes at
any time without notice. Please note that this manual applies to all models and explains variations
including accessories used. Therefore, you may find some explanations for variations and options not
installed on your equipment.

AC1204 Powermate Manual 10/01/18 Page 3 of 18
CONTENTS
PAGE NO.
WARRANTY
5
WARNING SECTION
6
IMPORTANT SAFETY INSTRUCTIONS
7
GENERAL DESCRIPTION OF APPLIANCE
& IMPORTANT OPERATING INSTRUCTIONS
8
GENERAL OPERATING INSTRUCTIONS
9
GENERAL MAINTENANCE
11
GENERAL FAULT FINDING
12
PARTS DIAGRAM
13
PARTS LIST
14
PARTS DIAGRAM
15
PARTS LIST
16
WIRING DIAGRAMS
17
DECLARATION OF CONFORMITY
18

AC1204 Powermate Manual 10/01/18 Page 4 of 18
This product is marked according to the European Directive (2002/96/EC) on
Waste Electrical and Electronic Equipment (WEEE).
The symbol on this product indicates that this product must not be disposed of with
normal household waste. Please protect human health and the environment by
disposing of this product responsibly in the correct manner.
For further information regarding the disposal, treatment, recycling and recovery of
this product, please contact:
Prochem Europe Sales Department
Telephone: [phone]
Prochem Europe Ltd. EEE Producer Registration Number: WEE / AJ0044SY
European Directive (2011/65/EU) Restriction of use of certain Hazardous
Substances in Electrical and Electronic Equipment (RoHS2).
This equipment does not contain more than the maximum permitted levels by
weight of the following substances:
Lead (Pb), Mercury (Hg), Cadmium (Cd), Hexavalent Chromium (Cr (Vl)),
Polybrominated Biphenyls (PBB), Polybrominated Diphenyl Ethers (PBDE)

AC1204 Powermate Manual 10/01/18 Page 5 of 18
MACHINE WARRANTY
DATE EFFECTIVE: 1/7/15
As of the above date, this warranty supersedes all previous warranties and forms part of the contract of sale.
Prochem Europe Ltd. (hereafter referred to as “Prochem”) guarantees this machine to be free from defects in materials and
workmanship for the relevant time period as shown below, and from the actual date of purchase by the user. Proof of the purchase
date from a Prochem Authorised Distributor will be required for performance of this warranty.
Rotationally moulded polyethylene tanks ……………………………………………………………………………………2 Years
All other parts except maintenance items (see below) …………………………….………………………………………..1 Year
THIS WARRANTY EXCLUDES NORMAL MAINTENANCE ITEMS, including but not limited to HOSES, FILTERS, O-RINGS,
DIAPHRAGMS, VALVES, DRIVE BELTS, GASKETS, CARBON BRUSHES and damage to motors and other components as a
result of failure to replace normal maintenance items. THIS LIST IS NOT EXHAUSTIVE.
To obtain performance of this warranty, contact the Prochem Authorised Distributor who supplied the product.
The Prochem Authorised Distributor is responsible as the selling agent for the provision of initial training in the correct
use and application of the machine and approved chemicals. The distributor is also responsible for service maintenance
and repairs during and after the warranty period and the administration of any warranty claims in conjunction with the
Prochem Service Department. Failure of any of these provisions and responsibilities may invalidate the warranty and
the authorised status of the distributor.
If Prochem receives notice of any defects during the warranty period, Prochem reserves the right to either repair, or replace
components that prove to be defective. Goods must be returned before the warranty is approved. Goods sent out prior to the
return of faulty items will be invoiced at current prices, subject to standard payment terms (see Prochem Standard Terms and
Conditions of Sale). Replacement parts supplied under warranty will be guaranteed for the remainder of the original machine
warranty and NOT from the date of installation. Spare parts supplied after expiry of machine warranty may be covered by a
manufacturer’s warranty, subject to inspection by Prochem Europe Ltd. and at its sole discretion. Normal maintenance items,
however, are not covered. Replacement or credit of any returned parts will be at the discretion of the Prochem Service
Department. Any subsequent refusal to accept their decision will serve to invalidate this warranty with immediate effect.
PROCHEM AUTHORISED DISTRIBUTORS are responsible for machine and accessories service back up during and after the
warranty period. Prochem will furnish parts if the warranty is approved, but DISTRIBUTORS will be responsible for fitting, service,
labour and related charges including travel, if applicable, and the cost of returning the machine or parts to Prochem. If any
chargeable work is undertaken by Prochem for DISTRIBUTORS the labour, parts (if applicable) and return carriage will be
charged at FULL LIST PRICE. If warranty is approved due to genuine manufacturing defect, then labour charges and carriage
charges may be waived at Prochem’s discretion.
Prochem may send replacement parts to customers supplied by a DISTRIBUTOR or directly by Prochem, subject to the same
conditions of replacement and payment above. The customer, however, will be responsible for fitting, labour and the carriage
costs of returning repaired parts. Alternatively, Prochem will undertake warranty work at Chessington, subject to the same
conditions, but the customer will be responsible for all carriage charges.
Any of the following circumstances involving the machine will serve to invalidate this warranty:-
NORMAL WEAR, ACCIDENTS, USE OF THE MACHINE FOR A PURPOSE OTHER THAN THAT FOR WHICH IT WAS
INTENDED, INCORRECT MAINTENANCE, THE USE OF CHEMICALS OTHER THAN THOSE SUPPLIED OR APPROVED BY
PROCHEM, INCORRECT INSUFFICIENT OR NON-USE OF DEFOAMER, EXPOSURE TO EXTREME TEMPERATURES OR
CONDITIONS, INCORRECT INSTALLATION OR REPAIR & UNAUTHORISED INTERVENTION.
Your Prochem unit is designed to give you many years of reliable service. If a problem should arise during or after the warranty
period, contact the Prochem Authorised Distributor or the Prochem Service Department, for details of the services available. Only
the original purchaser of the new equipment may seek performance of this warranty – these rights cannot be transferred to a
third party.
Prochem Europe Ltd.
Oakcroft Road, Chessington, Surrey KT9 1RH, ENGLAND
Telephone: + 44 (0)20 8974 1515 Fax: + 44 (0)20 8974 1511 Machine Warranty Issue 10 1/7/15
Liability is excluded for the following: -
All forms of damage and special damage founded in tort (apart from death and personal injury) and contract law including
but not limited to consequential loss, loss of income and losses incurred in reliance of the contract; service, labour or third-
party charges and the cost of returning the machine or defective parts to Prochem or Prochem’s Authorised Distributor.
As against a person dealing as a consumer, this warranty creates specific rights in addition to any statutory rights, which
are unaffected. As against a person dealing otherwise than as a consumer, however, this warranty excludes any implied
term that the machine will correspond with a description or a product sample.
With the exception of some specific products which are labelled and intended to be used by a consumer, all equipment,
machinery, accessories, products, services and advice supplied by Prochem is intended for professional and industrial use
only.

AC1204 Powermate Manual 10/01/18 Page 6 of 18
WARNINGS!
•Warning!
Machines shall not be used by children. Children should be supervised to
ensure that they do not play with the appliance. This machine can be used by
people with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning the use of the machine in a safe way and understand the hazards
involved.
•Caution: this machine is for indoor use only.
•Caution:this machine shall be stored indoors only.
•Warning!
This machine must be disconnected from the mains during cleaning or
maintenance, when replacing any parts or converting the machine to another
function.
•Caution: under no circumstances should the machine be carried by or
bumped up a flight of stairs using the handle.

AC1204 Powermate Manual 10/01/18 Page 7 of 18
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ THE FOLLOWING IMPORTANT SAFETY INSTRUCTIONS (!!)
BEFORE ATTEMPTING TO USE THIS MACHINE. FAILURE TO OBSERVE THE
INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
!! CAUTION
Read the instruction manual before using the
appliance.
!! SOUND PRESSURE LEVEL
The sound pressure of this machine, when in use,
does not exceed 85 dB (A).
!! APPLIANCE SUITABILITY
This appliance is suitable for commercial use, for
example, in hotels, schools, hospitals, factories,
shops, offices and rental businesses.
!! FOR MAINS POWERED APPLIANCES during
cleaning and maintenance – the plug is to be
removed from the outlet socket.
!! TRAINING
You must be trained in the operation of this
machine before use. Please read this manual
carefully and obtain operating instruction from your
Prochem Distributor or authorised representative in
the correct use of this equipment and suitable
chemicals before attempting to clean.
!! REPAIRS
Should any repairs, including supply cord
replacement be required, we recommend that the
appliance be returned to an authorised dealer.
!! ELECTRICAL CABLE INSPECTION &
REPLACEMENT
This machine must be earthed while in use to
protect the operator from electric shock. It is
equipped with a sealed and approved EC three
conductor cable and three-prong 13A plug. If the
supply cord is damaged it must be replaced by a
special cord or assembly available from the
manufacturer or its service agent. During operation
a hazard may occur when running the machine over
the power supply cord. The power supply cord
should be regularly inspected for signs of damage.
If the power supply cord is damaged, it must be
replaced.
!! RCD CIRCUIT BREAKER
In common with other household and commercial
electrical equipment, an 'RCD' circuit breaker plug
device is strongly recommended for this type of
equipment.
!! EXTENSION CABLES
Avoid using extension cables with this machine. If
an extension cable is used it should be of a suitable
rating and no longer than 30 metres. Use only
three wire CE approved extension cable with CE
approved three-prong earthed plugs and three pole
receptacles that accept the machine 13 amp plug.
!! DO NOT use a multiple adaptor socket to connect
the machine and heating units or other devices to a
single extension cable.
!! DO NOT stand the machine in water to operate
such as during flood extraction.
SERIOUS INJURY OR DEATH MAY RESULT IF
MACHINE IS IMMERSED IN WATER!
!! DO NOT pull the machine by the power cable or
hoses.
!! DO NOT use this machine with or near flammable
vapours. These machines can ignite flammable
vapours such as fuels, solvents or thinners.
!! DO NOT operate the machine unless it is
completely assembled.
!! DO NOT attempt repairs or maintenance unless
you are suitably qualified or experienced. Repairs
and maintenance should only be performed by
qualified personnel and the machine should be
tested for electrical safety before re-use.
!! SPRAY LIQUID ejection could be hazardous as a
result of its temperature, pressure or chemical
content.
!! ALWAYS disconnect machine from mains supply
when left unattended when cleaning the appliance.

AC1204 Powermate Manual 10/01/18 Page 8 of 18
GENERAL DESCRIPTION OF APPLIANCE
The AC1024 Powermate is an accessory for use with Hot Water Extraction Carpet Cleaning
machines.
It has a mains electricity supplied motor driven rotary brush and a spray tip.
The unit attaches by a high-pressure solution hose and vacuum suction hose to the main
machine and to the mains electricity outlet via a power cord.
IMPORTANT OPERATING INSTRUCTIONS
PLEASE READ THE FOLLOWING IMPORTANT OPERATING INSTRUCTIONS (!)
BEFORE ATTEMPTING TO USE THIS MACHINE. FAILURE TO OBSERVE THE
INSTRUCTIONS MAY RESULT IN DAMAGE TO THE EQUIPMENT.
! DO NOT expose the machine to rain or freezing
temperatures. Drain solution system and store
indoors when not in use.
! DO NOT operate the machine without solution and
waste tank filters.
! DO NOT use boiling water or temperature in
excess of 76OC.
! DO NOT use chemicals in the machine other than
those manufactured or recommended by Prochem
Europe.
! DO NOT use the machine for dry vacuuming. The
vacuum must only be used for wet extraction in
conjunction with the spray system.
! DO NOT run the solution pump and/or heating unit
dry. Always switch off and disconnect the machine
and/or heating unit electrical supply when re-filling
with solution.
! ALWAYS use a clean bucket to fill the solution
tank.
! AFTER USE flush solution system and rinse the
waste tank with clean water and remove loose
fibres from the vacuum filter.
! ALWAYS observe directions and safety
precautions on chemical products.
! ALWAYS pre-test carpet or fabric for colour
fastness and suitability with ready-to-use cleaning
solution before proceeding.
! ALWAYS use defoamer in the waste tank to
control foaming from previous shampoo residues in
the carpet.
! IF POWDERED CHEMICALS are used, always
premix in a separate bucket before adding to
solution tank. If not properly dissolved, powdered
cleaning solution may result in damage to the
solution pump.
! USE ONLY genuine replacement parts for this
machine, supplied by an authorised Prochem
Distributor.
! DO NOT use this machine for any purpose other
than for its intended design function. Any deviation
from its proper use or purpose and any
consequential damage that may occur is the sole
responsibility of the user.
! ALWAYS discharge soiled solution to a sewage
drain linked to a sewage treatment facility.
! DO NOT discharge soiled solution into roadside
storm drains.
! DO NOT use the drain valve to lift the machine
which may result in damage to the drain valve or
leakage from the drain valve mounting.

AC1204 Powermate Manual 10/01/18 Page 9 of 18
GENERAL OPERATING INSTRUCTIONS
UNPACKING YOUR NEW AC1204 POWERMATE:
When your package is delivered, check the carton carefully for signs of rough handling. If your AC1024 is
damaged, notify the carrier immediately and request an inspection. Be sure to keep the carton, packing inserts,
packing lists and carrier’s receipt until the inspector has verified your claim.
PROCHEMS liability ceases when the carrier picks up the shipment. However, our customer service staff will be
happy to furnish any information needed in connection with the claim and will attempt to expedite a resolution.
PLEASE READ BEFORE OPERATING YOUR NEW AC1204 POWERMATE:
Read the manual carefully and completely before attempting to operate the unit. This manual has important
information for the use and safe operation of the machine. Keep this manual handy at all times.
This equipment has been engineered and manufactured to provide excellent performance and service.
To ensure that your equipment will continue to perform as intended:
Maintain equipment regularly- following the suggested maintenance schedule provided.
Use only original PROCHEM parts when servicing.
Operate equipment with care.
If additional information is needed, please contact:
PROCHEM 0208 974 1515
All information and specifications printed in the manual are current at the time of printing; however, because of
PROCHEMS policy of continual product development, we reserve the right to make changes at any time without
notice.
Preparing the AC1024 POWERMATE for Use.
Set up your extraction machine ensuring that the machine has solution in the solution tank and the waste tank is
empty and defoamer has been drawn through the vacuum hose.
1. Attach the solution hose to the Powermate via the female quick connect on the handle.
2. Attach the 11/2 in cuff of the vacuum hose onto the Powermate tube handle.
3. Ensuring that the power switch of the Powermate is in the off position plug the power cord into the 13A
mains supply.
Operating the AC1204 POWERMATE.
The Powermate is now ready for use.
1. Switch on the pump and vacuums of the main parent machine.
2. Switch on the Powermate the green switch should illuminate.
3. You can now squeeze the trigger on the solution valve and use the Powermate to agitate the solution in
the carpet fibre and vacuum up the used waste solution.
Practical use of the AC1204 POWERMATE
Once the above instructions have been carried out the Powermate must be operated in the following manner.
1. Tilt back the AC1204 so that the brush is clear of the carpet and push the unit forward to full extent of
arm movement.
2. Tilt the AC1204 forward until the brush contacts the carpet.
3. Tilting the unit to maintain contact squeeze the solution valve trigger and pull the unit towards you.
4. This is the end of the cleaning stroke you should notice waste solution being drawn through the front
clear suction cover.
5. Under no circumstances should the AC1204 be pushed forward with the brush in contact with
the surface being cleaned, this action will result in the machine being damaged.

AC1204 Powermate Manual 10/01/18 Page 10 of 18
Packing up the AC1204 POWERMATE after use.
When the cleaning task is finished.
1. Switch off the Powermate the switch illumination will extinguish and the brush will stop turning.
2. Remove the plug from the mains outlet.
3. Flush the Powermate with clean water when you flush the pump system on the parent machine.
4. Disconnect the solution line and release any pressure in the Powermate by depressing the solution
valve trigger.
5. Recover the power cord and wind around the cord wrap hooks for safe storage.
Storage of the AC1204 POWERMATE
The AC1204 Powermate must be stored indoors in a clean warm environment.
1. If you expose the AC1204 to freezing conditions it will result in serious damage to the unit.
2. If you expose the AC1204 to rain or a flooded environment you will cause serious damage to the unit
and could in certain circumstances cause injury to the operator.

AC1204 Powermate Manual 10/01/18 Page 11 of 18
GENERAL MAINTENANCE
MAINTENANCE:
This AC1204 has been engineered and built to require minimum maintenance. But like any machine, it does
require some care to keep it in optimum working condition. Careful attention to these maintenance instructions
will give you maximum operating performance and life expectancy of the machine.
CAUTION: Disconnect the power cord from the outlet before doing any clean up or maintenance on the
machine.
DAILY MAINTENANCE:
Some maintenance of the AC1204 Powermate will be required.
1. Flush solution line with clean water by filling the solution tank of the parent machine and spraying.
2. Keep the exterior of the Powermate free from dust and debris by wiping it down with a cloth.
3. Inspect the Power Cord for damage, do not use the Powermate with a damaged power cord.
4. Remove any hair or debris from the rotating brush.
5. Check the spray tip for any debris and clean if necessary.
6. Check security of all nuts and screws paying particular attention to the trigger valve hanger.
DO NOT ATTEMPT REPAIR
INSTRUCTION FOR THE REPLACEMENT OF POWER CORD WITH COMBINED PLUG (ALL MACHINES)
Should the power cord require replacement please follow the instructions below.
1. The replacement cord and plug shall be of the same specification as the original, Prochem part number
BE4901(3 core, 1.5mm with 13Amp sealed plug unit)
2. Ensure that the machine is disconnected from the electrical supply and open the electrical housing by
means of the tool required.
3. Disconnect the live (brown), neutral (blue) and earth (green/yellow) wires from the cable terminal block
by unscrewing the terminal block clamp wire screws.
4. Release the outer cable clamp next to the terminal block by unscrewing the two securing screws, then
unscrew the outer cable gland to release the cable which can then be pulled out of the cable gland
assembly.
5. Insert the new cable through the gland, then secure and clamp the outer cable by means of tightening
the outer gland and the two securing screws next to the terminal block.
6. Connect the live (brown), neutral (blue) and earth (yellow/green) to the cable terminal block ensuring that
the earth strand is longer than the live and neutral strand as follows.
The conductor of the wire coloured brown shall be connected to the terminal marked (L), the conductor of
the wire coloured blue shall be connected to the terminal marked (N) and the conductor of the wire
coloured yellow and green shall be connected to the terminal marked with the earth symbol.
7. Ensure that all connections are secure, close the machine electrical housing and secure with the tool
required.
8. A Portable Appliance Test (PAT) should now be carried out.
!!Caution – only qualified maintenance personnel
should attempt the following repair

AC1204 Powermate Manual 10/01/18 Page 12 of 18
GENERAL FAULT-FINDING GUIDE
PROBABLE CAUSES CORRECTIVE ACTION
Defective power cord Replace Power Cord
Blown plug fuse Replace fuse
House or Building circuit breaker tripped Reset breaker switch.
PROBABLE CAUSES CORRECTIVE ACTION
Parent machine pump inoperative or defective Repair pump
Spray tip blocked Clean spray tip
Blockage in solution line Clear blockage
Defective Trigger Valve Assembly Repair or replace trigger valve Assembly
Damaged solution hose connectors Replace solution hose connectors
PROBABLE CAUSES CORRECTIVE ACTION
Damaged suction cover Replace suction cover
Glide missing or defective Replace glide
Damaged vacuum hose Replace vacuum hose
Blocked vacuum hose and tube Remove blockage.
PROBABLE CAUSES CORRECTIVE ACTION
Same as no power Same as no power
Defective switch Replace switch.
Broken drive belt Replace drive belt
Defective motor Replace motor
NO POWER
With the unit plugged into the mains outlet and the brush motor switched to on.
NO OR MINIMAL SPRAY
With solution hose connected, parent machine pump on and functioning correctly, trigger valve squeezed.
NO OR MINIMAL VACUUM
With vacuum hose connected to parent machine and vacuum switched on and functioning correctly.
NO BRUSH ACTION
With unit connected to the mains and brush switch in the on position.

AC1204 Powermate Manual 10/01/18 Page 13 of 18

AC1204 Powermate Manual 10/01/18 Page 14 of 18
PARTS LIST
ITEM
STOCK CODE
PART NUMBER
DESCRIPTION
QTY
1
E02200
B02200
CABLE CLAMP
1
2
D00352-3
LEVER VALVE
1
3
A00065P
¼ BARB X ¼ MP NYLON
1
4
H00564-2
WARNING LABEL TO AVOID ELECTRIC
SHOCK
1
5
E00525
G00525
PH VALVE
1
6
C00303
1/8 X ¾ TUBULAR PIVOT
7
E00095-1
A00168-18
BUSH ¼ - 1/8
1
8
J00651
SCREW CLAMP ¼ HOSE
1
9
E02494-1A
02494-1A
CORD HOOK SET 1 1/4
1
10
D02382
HANDLE, ONE PIECE
1
11
J00596
¼ BRAIDED HOSE
4
12
C00310-38
8-32 X 3/8 RH MACHINE BLACK PHILLIPS SS
25
13
BE4901
POWER CORD
1
14
E00214-2
B00214-2
COVER, SWITCH, ROCKER
1
15
E02211-1
B02211-1
SWITCH ILLUM GREEN 240V
1
16
G02531-1
WHEEL, 4.25 X 3/8
2
17
82331-2A
AXLE ASSY
1
18
C00312-1
10-32 X 1 1/8 TRUSS HEAD BLACK ZINC
2
19
B02212
LIQUID TIGHT STRAIN 3/8 NPT WITH NUT
1
20
82490A
MOTOR HOUSING ASSY
1
21
E82491A
82491A
SUCTION HEAD LENS
1
22
F02492
BOTTOM COVER
1
23
F02493
BELT ACCESS COVER
1
24
82363A
MOTOR STRAP ASSY
2
25
E82424A
82424A
BEARING SHAFT ASSY
1
26
G00528-3
BRUSH BEARING
2
27
E80508-1A
80508-1A
BRUSH ASSY
1
28
E02445
E02445
MOTOR BELT
1
29
D00356-4
WEIGHT BLOCK
1
30
E00091
A00091-1
SPRAY TIP 110/08 1/8 MP BRASS
1
31
00185-6A
UE WIRE ASSY
1
32
B00190
4 NYLON TIE
1
33
E03428
MOTOR SEAL GASKET
1
34
G00539
PW MOTOR
1
35
GU00102
A00102
FEMALE QC
1
36
E00053
A00053
45 ELBOW ¼ MP X ¼ FP
1
E90001A
RFI/ EMC FILTER (Not Shown)
1

AC1204 Powermate Manual 10/01/18 Page 15 of 18

AC1204 Powermate Manual 10/01/18 Page 16 of 18
ITEM
STOCK CODE
PART NUMBER
DESCRIPTION
QTY
1
GU00102
A00102
FEMALE QC
1
2
E00095-1
A00168-18
BRASS BUSHING
1
3
E11527A
11527A-PW
1/8 HP HOSE ASSY
1
4
E11593A
G13658
VALVE WITH BRACKET
1
5
CH4018
A00114B
HEX NIPPLE 1/4MP X 1/8MP
1
6
E12964
A12964
¼ BRASS COUPLER
1
7
D02382
WAND HANDLE
1

AC1204 Powermate Manual 10/01/18 Page 17 of 18
WIRING DIAGRAM AC1204

AC1204 Powermate Manual 10/01/18 Page 18 of 18
DECLARATION OF CONFORMITY
We:
Prochem Europe Ltd.,
Oakcroft Road,
Chessington,
Surrey, KT9 1RH
UK
(Importer / EC Responsible Person)
E.D.I.C
1753, Blake Avenue,
Los Angeles,
California, 90031-1006
USA
(Manufacturer)
Declare that the product(s):
Type(s): POWERMATE
Model(s): AC1204
Description: POWER BRUSH ACCESSORY
Has been tested to comply with the
2006/95/EC Low Voltage (LVD) Directive
A Technical file is held by Prochem Europe Ltd.
Certificate of compliance and test reports have been issued by:
Signed
(For and on behalf of the Importer / EC Responsible Person)
Name: J Hattersley
Position: Equipment Product Manager
Place of Issue: Chessington UK
Date of Issue: 22/01/2018