Progress Lighting Air Pro P2525 User manual

Date Purchased
Store Purchased
Model No.
Serial No.
Vendor No.
UPC
11221
PROGRESS LIGHTING 15-Year Limited Warranty
PROGRESS LIGHTING FAN MOTORS ARE WARRANTED TO THE END USER TO BE
FREE OF ELECTRICAL AND/OR MECHANICAL DEFECTS FOR A PERIOD OF 15
YEARS FROM DATE OF SALE. PULL CHAIN SWITCHES, REVERSE SWITCHES,
CAPACITORS AND METAL FINISHES ARE WARRANTEDFOR APERIOD OF 1 YEAR.
WARPING OF WOODEN OR PLASTIC BLADES IS NOT COVERED BY THIS
WARRANTY.
THE END USER HAS THE OPTION OF RETURNING THE DEFECTIVE FAN TO THE
PLACE OF PURCHASE DURING THE FIRST 30 DAYS FOR AREPLACEMENT. AFTER
30 DAYS, THE PURCHASER MUST CONTACT PROGRESS LIGHTING FOR REPAIR
OR REPLACEMENT. THE END USER ALSO BEARS THE RESPONSIBILITY FOR ALL
COSTS IN THE REMOVAL, SHIPPING AND REINSTALLATION OF FANS OR PARTS
FOR REPAIR OR REPLACEMENT.
PROGRESS LIGHTING WILL NOT ASSUME LIABILITY OR RESPONSIBILITY FOR
DAMAGES (INCLUDING INCIDENTAL OR CONSEQUENTIAL) CAUSED BY THE
IMPROPER INSTALLATION OR OPERATION OF THE UNIT OR ITS COMPONENT
PARTS, OR BY THE FAILURE OF SUPPORTING HARDWARE NOT SUPPLIED BY
PROGRESS LIGHTING. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER
GUARANTEES, WHETHER EXPRESSED OR IMPLIED, AND ISVOIDED IN CASES OF
ABUSE, MISUSE OR IMPROPER HANDLING, NEGLIGENCE, SHIPPING DAMAGE,
UNAUTHORIZED REPAIRS (MADE OR ATTEMPTED) OR UNUSUALAPPLICATION.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLUSIONS
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC RIGHTS AND
YOU MAY HAVE OTHER RIGHTSWHICH VARY FROM STATETO STATE.
15-Year Limited Warranty
785247147694 (BN)
785247147700 (WH)

Safety Rules.....................................................................................................................................
Unpacking Your Fan ........................................................................................................................
Installing Your Fan ...........................................................................................................................
..........................................................................................................................
Care of Your Fan ..............................................................................................................................
Troubleshooting .............................................................................................................................
Specifications ...............................................................................................................................
Operating Your Fan
1.
2.
3.
8.
9.
10.
11.
Table of Contents

1. To reduce the risk of electric shock, insure electricity has been turned
off at the circuit breaker or fuse boxbefore beginning.
2. All wiring must be in accordance with the National Electrical Code and
local electrical codes. Electrical installation should be performed by a
qualified licensed electrician.
3. WARNING: To reduce the risk of electrical shock and fire, do not use
this fan withany solid-state fanspeed control device.
4. WARNING: To reduce the risk of personal injury, use onlythe two steel
screws (and lock washers) provided with the outlet box for mounting to
the outlet box. Most outlet boxes commonly used for the support of
lighting fixtures are not acceptable for fan support and may need to be
replaced, consult aqualified electrician ifin doubt.
8. Avoid placing objectsin the path of the blades.
9. To avoid personal injury or damage to the fan and other items, be
cautious when workingaround or cleaningthe fan.
10. Do notuse water ordetergents when cleaningthe fan or fan blades. A
dry dust cloth or lightly dampened cloth will be suitable for most
cleaning.
11. After marking electrical connections, spliced conductors should be
turned upward and pushed carefully up into outlet box. The wires
should be spread apart with the grounded conductor and the
equipment-grounding conductor onone side ofthe outlet box.
12. Electrical diagrams are reference only. Light kit that are not packed
with the fan must be UL Listed and marked suitable for use with the
model fan you are installing. Switches must be UL General Use
Switches. Refer to the Instructions packaged with the light kits and
switches for properassembly.
WARNING
TO REDUCETHE RISK OFFIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT FAN TOOUTLET BOX MARKEDACCEPTABLE FOR
FAN SUPPORT.
5. The outlet box and support structure must be securely mounted and
capable of reliably supporting a minimum of 35 pounds. Use only UL
Listed outlet boxesmarked FOR FAN SUPPORT.
6. The fan must be mounted with a minimum of 7 feet clearance from the
trailing edge ofthe blades tothe floor.
7. Do not operate reversing switch while fan blades are in motion. Fan
must be turnedoff and blades stopped beforereversing blade direction.
WARNING
TO REDUCETHE RISK OFPERSONAL INJURY, DO NOTBEND THE
BLADE BRACKETS (ALSOREFERRED TO AS FLANGES)DURING
ASSEMBLYOR AFTERINSTALLATION. DO NOTINSERT OBJECTS IN
THE PATHOF THE BLADES.
NOTE
READ AND SAVE ALLINSTRUCTIONS!
1. Safety Rules

Unpack your fanand check thecontents. You should have the following items:
ab
c
3
1
24
5
6
7de
Unpacking Your Fan 2.
1.
2. Mounting plate
Set of blades(5)
3. Fan motorassembly
4. Motor housing
5. Set ofblades bracket (5)
6. Balancing kit
7. Loose partsbag containing:
b. Blade bracket attachment hardware
(1 screws withlock washers)
(3 screws)
d. Motor housing hardware
(4 screws)
(4 plastic wireconnectors, 1 Pullchain)
a. Blade attachmenthardware
(16 screws, 16Fiber washers)
c. Mounting hardware
e. Electrical hardware

3. Installing Your Fan
Tools Required
Phillips screw driver, straight slot screw
driver, adjustable wrench, step ladder, and
wire cutters.
Mounting Options
If there isn't an existing ULlisted mounting
box, then read the following instructions.
Disconnect the power by removing fuses or
turning off circuit breakers.
Secure the outlet box directly to the
building structure. Use appropriate
fasteners and buildingmaterials. The outlet
box and its support must be able to fully
support the moving weight of the fan (at
least 50 lbs).Do not useplastic outlet boxes.
To hang your fan where there is an existing
fixture but no ceiling joist, you may need an
installation hanger bar as shown in Figure 4
(available at yourProgress Lighting Retailer).
Outlet box
Outlet box
Outlet box
Figure 1
Figure 2
Figures 1,2 and 3 are examples of different
ways to mountthe outlet box.
WARNING
TO REDUCETHE RISK OFFIRE, ELECTRIC
SHOCK, OR OTHERPERSONAL INJURY,
MOUNT FAN ONLY TOAN OUTLETBOX
MARKED ACCEPTABLE FOR FAN SUPPORT
AND USE THEMOUNTING SCREWS
PROVIDED WITHTHE OUTLET BOX. OUTLET
BOXES COMMONLY USEDFOR THE SUPPORT
OF LIGHTING FIXTURESMAYNOT BE
ACCEPTABLE FORFAN SUPPORT ANDMAY
NEED TOBE REPLACED. CONSULT A
QUALIFIED ELECTRICIAN IFIN DOUBT.
Figure 3

Hanging the Fan
REMEMBER to turn off the power.
Follow the steps below to hang your fan
properly.
1. Attach the mounting plate to the outlet box
using the screws two screws and washers
provided with the outlet box.(Fig. 4). For
best performance be sure the mounting plate
is level and secured firmly against the ceiling.
You may need to insert additional washers
(not provided) between the outlet box and
mounting plate to make it level.
2. Carefully Lift the fan motor assembly
(without the blades) and insert the T section
of the motor housing plate into the slot in the
mounting plate as shown in Fig. 5.
You are now ready to make the electrical
connections.
4.
Figure 4
Figure 5
Outlet box
Mounting
plate
Screws
Outlet box
Solt
Fan
motor

5.
SUPPLY CIRCUIT
Ground
Conductor
Outlet Box
Green
Ground
Lead
Ground to
Downrod
BLACK
WHITEWHITE
BLACK
BLUE
GREEN
WHITE
BLUE
BLACK WHITE
Figure 6
Diagram indicates optionallight kit wiring.
WARNING
ELECTRICAL DIAGRAMSARE FOR
REFERENCE ONLY.OPTIONAL USEOF ANY
LIGHT KITSHALL BEUL LISTED AND
MARKED SUITABLEFOR USE WITHTHIS FAN.
Making the Electrical
Connections
Follow the steps below to connect the fan to your
household wiring. Use the wire connecting nuts
supplied with your fan. Secure the connectorswith
electrical tape. Make sure thereare no loose strands
or connections.
Step 1 Connect the fan supply (black) wire and
light supply (blue) wire to the black household
supply wire as shown inFigure 6.
Step 2. Connect the neutral fan (white) wire to the
white neutral household wire.
household
Step 4 After connecting the wires, spread them
apart so that the green and white wires are on one
side of the outlet box and the black wire is on the
other side.
REMEMBER to disconnect the power. If you feel
that you do not have enough electrical wiring
knowledge or experience, have your fan installed
by a licensed electrician.
Step 3 Connect the two green fan ground wires,
located on the mounting plate and motor, to the
ground wire.
WARNING
TO REDUCE THE RISKOF FIRE OR ELECTRIC
SHOCK, DO NOT USEA WALL MOUNTED
SOLID STATE SPEED CONTROLWITH THIS
FAN. IT WILLPERMANENTLYDAMAGE THE
ELECTRONIC CIRCUITRY.
Step 5 Turn the connecting nuts upward and
push the wiring into theoutlet box.

6.
Finishing the
Installation
1. Swing the motor assembly up into position
under the mounting bracket. Secure the
bracket to the plate with the screws provided.
(Fig. 7)
2. Carefully lift the motor housing onto the
mounting plate, properly align the holes
and tighten the motor housing with the four
screws supplied.(Fig. 8)
Figure 7
Figure 8
Mounting
plate
Screws
Motor Mounting
plate
Screws
Motor
housing

7.
Fiber
washer
Blade
arm
Figure 9
Blade
Screws
Attaching the Fan
Blades
Step 1 Attach the blades to the blade arms
using three screws and fiber washers as shown
in Fig. 9. Start a screw into the arm, do not
tighten. Repeat for the 2 remaining screws and
washers.
Step 2 Tighten each screw securely starting
with the center screw. Make sure the blade is
straight.
NOTE: Your fan blades are reversible. Select
the blade side finish which best accentuates
your decor.
Fasten the blade assembly to the motor
using the motorscrews provided.
Step 3
(Fig. 10)
Step 4 Install an optional light kit if you wish.
Follow the instructionsincluded with thekit.
Figure 10
Motor
Blade arm
Blade blancing
deviation
3. Use the enclosed Blade Balancing Kit if
the blade wobbleis still noticeable.
4. If the blade wobble is still noticeable,
interchanging two adjacent (side by side)
blades can redistribute the weight and
possibly result insmoother operation.
All blades are grouped by weight. Because
natural woods very in density, the fan may
wobble even though the blades are weighed
equally.
The following procedure should correct
most fan wobbling problems. Check after
each step.
1. Check that all blade and blade arm
screws are secure.
2. Most fan wobbling problems are caused
when blade levels are unequal. Check this
level by selecting a point on the ceiling
above the tip of one of the blades. Measure
this distance as shown in Figure 11. Rotate
the fan until the next blade is positioned for
measurement. Repeat for each blade. The
distance should be equal within
1/8".
'

Operating Your Fan 8.
WARNING
TO REDUCE THERISK OF PERSONALINJURY,
DO NOT BENDTHE BLADE HOLDERS
WHILE INSTALLING,BALANCING THE
BLADES, OR CLEANINGTHE FAN. DO NOT
INSERT FOREIGNOBJECTS BETWEEN
ROTATING FANBLADES. Turn on the power and check the operation of
your fan. There are two pull chains available in
your fan:
1. 3-speed pull chain- it controls the fan speed as
follows: 1 pull- High, 2 pulls- Medium, 3 pulls-
Low, and4 pulls- Off.
Speed settings for warm or cool weather
depend on factors such as the room size,
ceiling height, numberof fans, andso on.
The slide switch controls directions: forward
(switch down )or reverse (switchup ).
Warm weather - (Forward) Adownward air flow
creates a cooling effect as shown in Figure 12.
This allows you to set your air conditioner on a
higher setting without affecting your comfort.
Cool weather - (Reverse) An upward airflow
moves warm air off the ceiling area as shown in
Figure 13. This allows you to set your heating
unit on a lower setting without affecting your
comfort.
NOTE
WAITFOR FAN TO STOP BEFORE
CHANGING THE SETTING OF THE
SLIDE SWITCH.
Figure 12
Figure 13
Touching
ceiling
Figure 11

Here are some suggestions to help you
maintain your fan
1.Because of thefan's natural movement,
some connections may become loose.
Check the support connections,
brackets, and blade attachments twice
a year. Make sure they are secure. (It is
not necessary to remove fan from
ceiling.)
2. Clean your fan periodically to help
maintain its new appearance over the
years. Use only a soft brush or lint-free
cloth to avoid scratching the finish. The
plating is sealed with a lacquer to
minimize discoloration or tarnishing.
Do not use water when cleaning. This
could damage the motor, or the wood, or
possibly cause anelectrical shock.
3. You can apply a light coat of
furniture polish to the wood blades for
additional protection and enhanced
beauty. Cover small scratches with a
light application ofshoe polish.
4. There is no need to oil your fan.
The motor has permanently lubricated
bearings.
IMPORTANT
MAKE SURE THEPOWER IS OFFAT THE
ELECTRICAL PANEL BOX BEFOREYOU
ATTEMPTANY REPAIRS. REFER TO THE
SECTION "MAKING ELECTRICAL
CONNECTIONS"
9. Care of Your Fan

Problem
Fan will notstart.
Fan sounds noisy.
Solution
1.Check circuit fusesor breakers.
2. Check linewire connections tothe fan and switch wire connectionsin the switchhousing.
CAUTION: Make suremain power isoff.
1. Make sureall motor housingscrews are snug.
2. Make surethe screws thatattach the fan blade bracket tothe motor hubis tight.
3. Make surewire nut connectionsare not rubbing against each otheror the interiorwall of theswitch housing.
CAUTION: Make suremain power isoff.
4. Allowa 24-hour "breaking-in"period. Most noiseassociated with anew fan disappear during this time.
5. If usingan optional lightkit, make sure the screws securingthe glassware aretight. Check thatlight bulb is
also secure.
6.Some fan motorsare sensitive tosignals from solid-state variable speed controls.
If you haveinstalled this typeof control, choose and install anothertype of control.
7. Make surethe upper canopyis a short distance from theceiling. It should nottouch the ceiling.
Troubleshooting 10.

11. Specifications
2007 Progress Lighting, Inc.
701 Millennium Blvd
Greenville, SC 29607
All Rights Reserved
C
These are approximatemeasures. They do not include Amps and Wattageused by thelight kit.
RPM CFM N.W. G.W.
C.F.
52"
120 1.08'5.70
kgs
7.03
kgs
0.24
0.37
0.49
16
34
63
62
120
162
1025
3300
5200
120
120
Fan Size Speed Volts Amps Watts
Low
Medium
High