Bionaire BDTF1609-IN User manual

DUAL BLADE
TABLE FAN
pure indoor living
MODEL# BDTF1609-IN
INSTRUCTION MANUAL
Read instructions before operating. Retain for future reference.
LEARNING MORE
For a wealth of information about your fan and other Bionaire®products, visit our
website at www.bionaire.com.
THIS RODUCT IS MANUFACTURED TO COM LY WITH
THE E.E.C. DIRECTIVES 2006/95/EC AND 2004/108/EC.
Waste electrical products should not be disposed of with house-
hold waste. lease recycle where facilities exist. Check on the
following website for further recycling and WEEE information:
www.bionaire.com.
lease see warranty card for warranty information.
© 2009 Sunbeam roducts, Inc. doing business as Jarden Consumer Solutions. All rights
reserved. Manufactured by Sunbeam roducts, Inc. doing business as Jarden Consumer
Solutions, 2381 Executive Center Drive, Boca Raton, Florida 33431 U.S.A. Distributed
by Jarden Consumer Solutions of India rivate Limited, Unit Number B-204, Universal
Business ark Off Saki Vihar Road, Chandivli Farm Road Andheri (E), Mumbai 400-072,
India. Telephone : [phone]
rinted in RC
138031
S R-110409
OPERATING INSTRUCTIONS
(See Fi . 2 & 3)
1. Operate the relevant push button for
the required fan speed. “0” for “OFF”,
“1” for Low Speed, “2” for Intermediate
Speed and “3” for High Speed.
2. To make the fan head oscillate, push the
oscillation knob DOWN. To stop the
oscillation, pull the oscillation knob U .
3. Adjust the tilt of the fan head to the
desired angle by pushing gently up or
down on the fan guard.
CAUTION: The fan should be switched
off when making this ad ustment.
lease note that the head will not latch
into the low or mid position until the
guard and blade are fitted to the motor.
CLEANING
1. Switch off and unplug the power cord
before assembling or disassembling and
cleaning.
2. lastic parts should be cleaned using
mild detergent and a damp cloth or
sponge.
CAUTION: Do not use harsh
detergents, chemical cleaners,
gasoline or solvents as they may
damage the surface finish of the
plastic components. Also, do not
immerse in liquids.
NOTE: Unit must be unplugged for
it to be fully off.

BDTF1609-IN
Fi . 1
Fi . 2
4
985
732 1
Fi . 3
3
2
1
0
1. Oscillation Knob
2. Motor Asembly
3. Rear Guard
4. Guard Retaining Nut
5. Large Blade
6. Small Blade
7. Blade Retaining Nut
8. Guard Loop
9. Front Guard
10. Guard Loc ing Screw/Nut
11. Base
BDTF1609-IN
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
1. Read all instructions before using this
appliance.
2. To avoid fire or shock hazard, plug the
appliance directly into an appropriate
electrical outlet.
3. Keep the power cord out of heavy
traffic areas. To avoid fire hazard,
NEVER put the power cord under
rugs, near heat registers, radiators,
stoves, or heaters.
4. To protect against electrical hazards, DO
NOT immerse the appliance in water or
other liquids. Do not use near water.
5. NEVER drop or insert any objects into
the openings of the unit.
6.
Do not operate any appliance with a
damaged power cord or plug. If the motor
fails to operate or the unit has been
dropped or damaged in any manner,
return appliance to manufacturer for
examination and/or repair.
7. DO NOT use outdoors.
8.NEVER place on a soft surface such
as a bed or sofa as this could cause
the unit to tip over and block the air
inlet or outlet grills.
9. DO NOT place anything on top of unit.
10.WARNING: To reduce the risk of fire or
electric shock, DO NOT use this
appliance with any solid-state speed
control device.
11. CAUTION: In order to avoid a hazard
due to inadvertent resetting of the
thermal cutout, this appliance must not
be supplied through an external
switching device, such as a timer, or
connected to a circuit that is regularly
switched on and off by the utility.
12.This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety. Children should be
supervised to ensure that they do not
play with the appliance.
13.This product is not desgned or
intended to be used with an extension
cord.
ASSEMBLY INSTRUCTIONS
1. Remove the blade retaining nut
(turning clockwise) while holding motor
shaft. Then remove the guard retaining
nut (turning counter-clockwise). Take
off the motor shaft sleeve protector
and discard.
2. Set the rear guard in the proper
position (carry handle topmost) on the
motor assembly. Make sure that the
pins on the rear guard align with the
pins on the motor assembly. Then
screw on the guard retaining nut
(turning clockwise) until tight.
3. Install the large blade onto shaft of the
motor assembly. Then install the small
blade. The flat area of the “D” on the
blade should align with the flat area
of the “D” on the motor shaft. Screw
on the blade retaining nut (turning
counter-clockwise) until tight.
4. Open the guard locking screw/nut.
lace the guard loop on the rear guard
with the guard locking screw/nut at the
bottom. Assemble the front guard on
guard loop until all sides snap. Rotate
the front guard until the Bionaire logo
is horizontal.
5. Secure both guards firmly by fitting
and tightening the guard locking
screw/nut.
6. Remove the plastic screw from the
base (turning counter-clockwise). Then
affix motor assembly to base hole until
snapped. Tighten screw to the base.
ENGLISH
1011
6
4
98 5
732 1
3
2
1
0
10 11
6
HINDI