Progress lighting Airpro p250065 User manual

Ceiling Fan Installation Manual

P250065

93138704_C

Date Purch as ed

Store Purchased

Model No.

Serial No.

Ven d o r N o .

UPC

109226

Limited Lifetime Warranty

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so

long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to

be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic

blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of

any sea coast. Extended warranties for ENERGY STAR®qualified products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are

warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance

with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for

fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical

components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no

warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for

replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864) 678-1000 for repair or replacement

which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not

limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or

neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without

limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or

attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND

ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS

LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR

CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,

BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE OR NONINFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or

consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights

and you may have other rights which vary from state to state.

785247250042

785247250035

785247250059

Table of Contents

Safety Rules.....................................................................................................................................................................................

Unpacking Your Fan .......................................................................................................................................................................

Installing Your Fan .........................................................................................................................................................................

Installing the Decorative Cover .....................................................................................................................................................

Operating Your Transmitter ..........................................................................................................................................................

Care of Your Fan ...........................................................................................................................................................................

Troubleshooting ............................................................................................................................................................................

Specifications ................................................................................................................................................................................

10.

12.

13.

14.

1. Safety Rules

1. To reduce the risk of electric shock, insure electricity has been turned off

at the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan with any solid-state fan speed control device.

4. WARNING: To reduce the risk of fire, electric shock, or personal injury,

mount to outlet box marked "Acceptable for Fan Support of 15.9 kg (35 lbs.)

Or Less" and use mounting screws provided with the outlet box. Most outlet

boxes commonly used for the support of light fixtures are not acceptable for

fan support and may need to be replaced. Due to the complexity of the

installation of this fan, a qualified licensed electrician is strongly

recommended.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less.

Use only cUL-listed outlet boxes marked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 ft (2.1m) clearance from

the trailing edge of the blades to the floor.

7. To operate the reverse function on this fan, press the reversing button while

the fan is running.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

10. Do not use water or detergents when cleaning the fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

11. After making electrical connections, spliced conductors should be

turned upward and pushed carefully up into the outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet box.

12. Electrical diagrams are for reference only. Light kits that are not packed

with the fan must be cUL Listed and marked suitable for use with the

model fan you are installing. Switches must be cUL General Use

Switches. Refer to the Instructions packaged with the light kits.

NOTE

READ AND SAVE ALL INSTRUCTIONS!

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

Unpacking Your Fan 2.

15. Loose parts bag containing:

a. Blade attachment hardware

(37 3/16" x 10mm screws,

37 fiber washers)

b. Decorative rod holder attachment

hardware

(25 3/16" x 10mm screws,

25 fiber washers)

c. Blade arms attachment hardware

(25 1/4" x 15mm screws with

lock washers)

d. Mounting hardware

Wire nuts (3)

c d

Unpack your fan and check the contents. You should have the following items:

1. Fan blades (12)

2. Decorative rods (12)

3. Canopy assembly

4. Ball/downrod assembly

5. Collar cover

6. Set of blade brackets (12)

7. Decorative rod holders (12)

8. Fan motor assembly

9. Mounting plate

10. Decorative cover

11. Receiver

12. Remote control

13. 12V MN21/A23 battery

14. Balancing kit

812

Tools Required

Phillips screw driver, straight slot screw driver,

adjustable wrench, step ladder, and wire cutters.

Mounting Options

If there isn't an existing cUL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the

fan (at least 35 lbs). Do not use plastic outlet

boxes.

Figure 4

Figure 3

Figure 1

Figure 2

Outlet box

Outlet box Outlet box

Note: You may need a longer downrod to

maintain proper blade clearance when installing

on a steep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at your Progress Lighting Retailer).

3. Installing Your Fan

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR OTHER PERSONAL INJURY,

MOUNT FAN ONLY TO AN OUTLET BOX

MARKED ACCEPTABLE FOR FAN SUPPORT

AND USE THE MOUNTING SCREWS

PROVIDED WITH THE OUTLET BOX. OUTLET

BOXES COMMONLY USED FOR THE

SUPPORT OF LIGHTING FIXTURES MAY NOT

BE ACCEPTABLE FOR FAN SUPPORT AND

MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Angled ceiling

maximum

25 angle

Recessed

outlet box

Provide strong support

Ceiling

hanger

bracket

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps below to hang your fan properly:

Step 1. Remove the decorative canopy bottom

cover from the canopy by turning the cover

counter clockwise.(Fig. 5)

Step 2. Remove the mounting bracket from

the canopy by removing the 1 of 2 screws

from the bottom of the mounting bracket and

loosening the other one a half turn from the

screw head. Next, turn the canopy counter

clockwise to removing the mounting bracket

from the canopy. (Fig. 5)

Step 3. Pass the 120-volt supply wires

through the center hole in the ceiling hanger

bracket as shown in Fig. 6.

Step 4. Secure the hanger bracket to the

ceiling outlet box with the screws and

washers provided with your outlet box.

Step 5. Remove the hanger pin, lock pin and

set screws from the top of the motor

assembly. (Fig. 7)

Step 6. Route the safety cable and wires

exiting from the top of the fan motor through

the collar cover, canopy cover, canopy and

then through the ball / downrod. (Fig. 7)

Step 7. Align the holes at the bottom of the

downrod with the holes in the collar on top of

the motor housing (Fig. 7). Carefully insert

the hanger pin through the holes in the collar and

downrod. Be careful not to jam the pin against the

wiring inside the downrod. Insert the locking pin

through the hole near the end of the hanger pin until it

snaps into its locked position, as noted in the circle

inset of Fig. 7.

WARNING

FAILURE TO PROPERLY INSTALL

LOCKING PIN AS NOTED IN STEP 7

COULD RESULT IN FAN LOOSENING AND

POSSIBLY FALLING.

Figure 6

Figure 7

Ceiling

hanger

bracket

Mounting screws

(supplied with

electrical box)

CUL Listed

electrical

box

120V Wires

Washers

Supply wires

Downrod

Hanger pin Lock pin

Set screws

Canopy

Canopy cover

Collar cover

Pin in locked

position

Step 8. Tighten two set screws on top of the fan

motor firmly. (Fig. 7)

Step 9. Place the downrod ball into the hanger

bracket socket.

Step 10. Secure the safety cable to the building

structure with a wood screw. (wood screw not

supplied)

Figure 5

Ceiling hanger

bracket

Ceiling

canopy

Canopy

cover

Safety cable

Make the Electrical

Connections

WARNING: To avoid possible electrical shock,

be sure electricity is turned off at the main fuse

box before wiring.

WARNING: Check to see that all connections

are tight, including ground, and that no bare wire

is visible at the wire nuts, except for the ground

wire.

CAUTION: To reduce the risk of electric shock,

this fan must be installed with an isolating wall

control/switch.

NOTE: The fan must be installed at a maximum

distance of 20 ft. from the remote control for

proper signal transmission between the remote

control and the fan's receiving unit.

If you feel you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

Follow the steps below to connect the fan to your

household wiring. Use the plastic wire nuts with

your fan. Secure the plastic wire nuts with

electrical tape. Make sure there are no loose

strands or connections.

Figure 8

Step 1. Insert the receiver into the mounting

bracket with the flat side of the receiver facing the

ceiling.

Step 2. Make wire connections from the fan to the

receiver.

From Fan To Receiver

White Wire ---------White Wire "For Light"

Blue Wire ----------Blue Wire "For Light"

Yellow Wire -------Yellow Wire

Red Wire ---------- Red Wire

Grey Wire --------- Grey Wire

Step 3. Make wire connections from the filter to the

outlet box as follows, using the wire nuts.

From Filter To Outlet Box

Black Wire "AC in L" ------Black Wire (Hot)

White Wire "AC in N"------White Wire (Neutral)

From Fan, Filter & Receiver To Outlet Box

Green Wires* ----- Green or Bare Wire (Ground)

There are four green grounding leads: from the

mounting bracket, hanger ball/downrod assembly,

receiver and the filter.

Step 4. Turn the wire nut connections upward,

spreading them apart so the green (ground) and white

wires will be on one side of the outlet box and the black

and blue wires will be on the other side. Carefully tuck

the connections up into the outlet box.

White

Canopy

Black

Filter

Receiver

Outlet Box

White

Blue

Red

Yellow

Grey

Green

Ground conductor

Green

Finishing the Installation

Step 1. Tuck connections neatly into ceiling outlet

box.

Step 2. Slide the canopy up to mounting bracket and

place the key hole on the canopy over the screw on

the mounting bracket, turn canopy until it locks in

place at the narrow section of the key holes. (Fig. 9)

Step 3. Align the circular hole on canopy with the

remaining hole on the mounting bracket, secure by

tightening the two set screws. Note: Adjust the

canopy screws as necessary until the canopy and

canopy cover are snug.

Attaching the Fan Blades

Attaching the blades to the blade arms

Step 1. Attach the blades to the blade arms using the

three blade attachment screws (3/16" x 10mm) and

fiber washers. Start a screw with fiber washer into

the blade arms, but do not tighten.

Step 2. Repeat for the two remaining blade attach-

ment screws and fiber washers.

Step 3. Tighten each screw securely starting with

the center screw. Make sure the blade is straight.

Step 4. Attach the decorative rod holders to the

blades using the two decorative rod holder attach-

ment screws (3/16" x 10mm) and fiber washers.

Step 5. Tighten each screw securely starting and

make sure the blade is straight.

Step 6. Repeat these steps for the remaining blades .

WARNING

Make sure the notch on the hanging bracket

properly sits in the groove in the hanger ball before

attaching the canopy to the bracket by turning the

housing until it drops into place.

Outlet box

Canopy

cover

Canopy

Hanger

bracket

Figure 9

Screws

Figure 10

Blade screws

(3/16" x 10mm)

and fiber washers

Blades

Blade arms

Decorative rod

holders

Decorative rod

holder screws

(3/16" x 10mm)

and fiber washers

Attaching the Fan Blades (continued)

Attaching the decorative rod and fastening the blade

assemblies to the motor

WARNING: To reduce the risk of personal injury, do not bend the blade

arms while installing, balancing the blades, or cleaning the fan. Do not

insert foreign objects between rotating fan blades.

Step 1. Rotate the decorative rods onto the setscrew on the motor housing

and firmly tightened. (Fig. 11)

Step 2. Insert the decorative rods through the holes on the decorative rod

holder. (Fig. 11)

Step 3. Fasten the blade assemblies to the fan motor assembly. Tighten the

two blade arm screws with lock washers provided. (Fig. 11)

Step 4. Repeat this procedure for the remaining blade assemblies.

Figure 11

Decorative rods

Setscrew

Figure 12

Decorative rods

Decorative rod

holders

Blade assembly

Blade arm screws (1/4" x 15mm)

with fiber washers

Blade Balancing

All blades are grouped by weight. Because

natural woods very in density, the fan may

wobble even though the blades are weighed

equally.

The following procedure should correct most

fan wobbling problems. Check after each step.

1. Check that all blade and blade arm screws are

secure.

2. Most fan wobbling problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

this distance as shown in Figure 13. Rotate

the fan until the next blade is positioned for

measurement. Repeat for each blade. The

distance deviation should be equal within

1/8".

3. Use the enclosed Blade Balancing Kit if the

blade wobble is still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result in smoother operation.

Touching

ceiling

Figure 13

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

HOLDERS WHILE INSTALLING,

BALANCING THE BLADES, OR CLEANING

THE FAN. DO NOT INSERT FOREIGN

OBJECTS BETWEEN ROTATING FAN

BLADES.

Installing the

Decorative Cover

CAUTION: Before starting installation,

disconnect the power by turning off the circuit

breaker or removing the fuse at fuse box. Turning

power off using the fan switch is not sufficient to

prevent electric shock.

Step 1. Remove the 1 of 3 screws from the posts

of the mounting ring and keep it for future use.

Loosen the other 2 screws. (Do not remove)

Step 2. Place the key holes in the mounting plate

over the two screws previously loosened from the

mounting ring. Turn the mounting plate until the

decorative cover locks in place at the narrow

section of the key holes. (Fig. 14)

Step 3. Securely tighten the two mounting screws

previously loosened and the one previously

removed.

Step 4. Position the notches in the outer rim of

the mounting plate so they line up with the tabs

on the decorative cover. Carefully lift the

decorative cover up inside the mounting plate and

secure it to the fan by turning the decorative cover

clockwise until snug. DO NOT OVERTIGHTEN.

Figure 14

Installing the battery

Install a 12V MN21/A23 battery (included) into the

remote control. To prevent damage to the remote

control, remove the battery if not used for long

periods. (Fig. 15)

Figure 15

Screws

Mounting

ring

Mounting

plate

Tab

Decorative

cover

Operating Your Transmitter 10.

Figure 17

Figure 16

Your DC brushless motor is equipped with an

automatically learned type remote control. There is

no frequency switches on the receiver or transmitter.

The fan can start to use once the pairing process is

done.

Remote Control Button Definitions:

These six buttons are used to set the fan speed as

follows:

I = minimum speed

II = low speed

III = medium low speed

IV = medium speed

V = medium high speed

VI = high speed

button: Turns the fan off.

button: Controls fan direction.

button: This button is to control optional light on or off.

Press and hold the button to activate the dimmer function.

Setting the Remote Control

Follow the below steps to set the remote control:

The auto learning function will only mandate within

60 seconds when turning the fan’s AC power ON.

With the fan’s power off, restore power to the fan. Press

and hold “SET” button for about 5 seconds and release.

If optional light kit is installed, the light kit will flash

twice and the signal light on the remote control will

come on when the button is pressed. The fan has

completed the pairing process with the remote control

and is ready for use.

NOTE: If the self calibration test failed, turn

the AC power off; restore power and process

the self calibration test again.

NOTE: During self calibration test, the remote

is non-fuctional.

NOTE: The learning frequency function and

self calibration test will continue to retain the

last set frequency and calibration set even

when the AC power is shut off. If the

frequency is changed the self calibration test

will occur again.

Over 80W protection: When the receiver

detects motor power consumption which is

greater than 80W, the receiver power will be

stopped and operation will immediately

discontinue. Wait for 5 seconds and then turn

the receiver power back on.

Speed settings for warm or cool weather depend on

factors such as the room size. Ceiling height, number

of fans and so on.

NOTE: To operate the reverse function on this fan,

press the reverse button while the fan is running.

Warm weather - (Forward) A downward airflow

creates a cooling effect as shown in Fig. 18. This

allows you to set your air conditioner on a warmer

setting without affecting your comfort.

Cool weather - (Reverse) An upward airflow moves

warm air off the ceiling area as shown in Fig. 19. This

allows you to set your heating unit on a cooler setting

without affecting your comfort.

Figure 18

Figure 19

11.

Here are some suggestions to help you maintain your

fan

1. Because of the fan's natural movement, some

connections may become loose.

Check the support

connections, brackets, and blade attachments

twice a year.

Make sure they are secure.

(It is not

necessary to remove fan from ceiling.)

2. Clean your fan periodically to help maintain its new

appearance over the years. Use only a soft brush or

lint-free cloth to avoid scratching the finish. The

plating is sealed with a lacquer to minimize

discoloration or tarnishing. Do not use water when

cleaning. This could damage the motor, or the wood,

or possibly cause an electrical shock.

3. You can apply a light coat of furniture polish to the

wood blades for additional protection and enhanced

beauty. Cover small scratches with a light application

of shoe polish.

There is no need to oil your fan.

The motor has

permanently lubricated bearings.

IMPORTANT

MAKE SURE THE POWER IS OFF AT THE

ELECTRICAL PANEL BOX BEFORE YOU

ATTEMPT ANY REPAIRS. REFER TO THE

SECTION "MAKING ELECTRICAL

CONNECTIONS"

Care of Your Fan

12.

13.

Troubleshooting

Solution

1. Check circuit fuses or breakers.

2. Check line wire connections to the fan and switch wire connections in the switch housing.

CAUTION: Make sure main power is off.

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade bracket to the motor hub is tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.

CAUTION: Make sure main power is off.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear during this time.

5. If using an optional light kit, make sure the screws securing the glassware are tight. Check that light bulb is also secure.

6. Some fan motors are sensitive to signals from solid-state variable speed controls. If you have installed this type of control,

choose and install another type of control.

7. Make sure the upper canopy is a short distance from the ceiling. It should not touch the ceiling.

1. Turn the AC power off to fan, and re-do steps for programming on page 10.

2. Do not turn off fan from standard wall switch. Use only our wall switch or your remote to regulate fan.

Problem

Fan will not start.

Fan sounds noisy.

Fan has lost its

programming

repeatedly.

Specifications

14.

29.81

lbs

33.37

lbs

2.54'

Fan Size Speed Volts Amps Watts RPM CFM N.W. G.W. C.F.

52"

Low

High

120

These are approximate measures. They do not include Amps and Wattage used by the light kit.

0.08

0.39

3.85

29.66

112

2745.38

6296.22

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

701 Millennium Blvd.,

Greenville, SC 29607

Manuel d’installation du ventilateur de plafond

P250065

93138704_C

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.