progressive automations TY-01 User manual

TY-01
User Manual
Page 2
Page 2
Page 2
Page 3
Parts
Dimensions In Inches
Specifications
Tools Required
Hardware
Assembly Instructions
Page 3
Contents
Page 4-6

Parts
Dimensions In Inches
2
Control box
Wireless remote
28.98
Retracted: 31.89”
Extended: 70.89”
27. 17
11.81
16.69
7.09
2.95 2.95
1.18
1.97
1.26
32
5.67
5.55
7.09
0.39
m6
Specifications
Dynamic Load
Retracted Length
Speed at Full Load:
Output Voltage:
Weight:
Overload Protection:
Duty Cycle:
IP Grade:
Operational Temperature:
Certification:
Tube Material:
120V~ 60Hz, 86W
Yes
10% (2 minutes on, 18 minutes off)
IP20
CE and UL
Powder painted steel tube
-5ºC~+20C (23ºF~104ºF)
130 lbs
0.98"/sec
31.89"
Input Voltage:
Stroke Length: 39"
24VDC 2A
42 lbs
Static Load 150 lbs
Color: Black
Control Options: RF remote/ Wired remote

2
Screws M5×50
4
Screws M6×16
8
Hex Bolts
M6×14
4
Hex Bolts
M8×16
4
Nuts M8
8
Spring washers M6
8
Washers M6
3
Tools Required
Allen Wrenches
M6 M8
Philips head screw
Hardware
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
1
8
8
8
2
1
4
1
4
4
2
1
1
1
Mounting base
Column
Washers M6
Spring washers M6
Hex Bolts M6x14
Screws M5x50
TV mounting bracket
Nuts M8
Mounting bracket
Screws M6x16
Screws M8X16
Connection cable and power cable
Remote
Handset
Control box
No. Type Qty

4
Assembly Instructions
Use 4 Hex Bolts M6x16, each with Spring washer and Washer, to attach
Bases to the bottom of the Column. Tighten the 4 Screws (2 per side).
1
Use 4 Hex Bolts M6x16, each with Spring washer and Washer,
to attach Mounting bracket to the top of the Column.
Tighten the 4 Screws.
2
Use 4 Screws M6x16, to assemble the TV mounting
bracket as following.
3
Use 4 Hex Bolts M8x16, each with Spring washer and Washer, to attach TV
mounting bracket on to the Mounting bracket. Tighten the 4 Screws.
4

8
Down
Button
Up
Button
LED
Assembly Instructions
5
Secure another 2 parts of the TV mounting bracket onto
the backside of the TV set with 4 screws included with
TV set. And then hang the TV set onto the TV mounting
bracket as following.
Use 2 M5x50 screws to tighten on the bottom.
5
Connect the Wires as per the diagram
below. Now your TV lift is ready for use.
(press the buttons of the handset and
column will move up/down)
6
Operating: You can use the remote or handset operate
the TV lift.
(1) Remote: Press S1+S3, TV lift move up, press S2+S3, TV
lift move down.
(2) Handset: Press UP button, TV lift move up, press DOWN
button, TV lift move down. (3) During the movement, you
can press any button on remote or handset (not the RESET
button on handset), TV lift stop at once.
7
S1
S3
S2
Setting the UPPER and LOWER limits:
•Press and hold the UP button (red) on the control box
while simultaneously pressing the UP button on the
handset. Raise the TV lift to the desired height. Release
both UP buttons to set the UPPER limit.
•Press and hold the DOWN button (black) on the control
box while simultaneously pressing the DOWN button on
the handset. Lower the TV lift to the desired height.
Release both DOWN buttons to set the LOWER limit.
Both UPPER and LOWER limits have now been set.

Assembly Instructions
6
9Reset the TOP and BOTTOM position: You may want to reset
the TOP position higher than the original TOP position and
BOTTOM position lower than the original BOTTOM position.
To reset the UPPER and LOWER limits, please follow step 8.
Some other information:
(1) Frequency study: If you lose the wireless remote and buy a
new remote from your local distributor, the frequency of the
new remote may not match with your control box. You should
STUDY the frequency between the remote and control box
with the following procedure:
1. Press any button S1 (or S2 and S3) and the STUDY
button on the handset at the same time and hold them.
Several seconds later, the LED on handset will blink and
you finish the frequency study. You can now use the
new remote to operate this TV lift.
2. Time protection: In order to prevent from “playing” with
the TV lift, there is a time limit protection implemented.
You can only operate the TV lift for 3-minutes within a
20 minute time period. If the operation time exceeds 3
minutes, the system will stop moving and the LED on
the control box will blink. You should wait for 20
minutes or remove power from the control box.
Afterwards you can operate the TV lift again.
3. RESET the system: If a problem occurs when operating
the system, for example, a cable connection problem or
the TV lift won't move when you press the UP/DOWN
buttons, you should try to RESET the system by the
following procedure:
Warning: The TV lift will move to the zero position when
RESET. Be sure there is no obstruction under the TV set.
Disconnect and reconnect the cables. Turn off the power of
the control box and turn on the power again. Be sure the
green LED on the control box is light on.
Press the RESET button on handset and hold it. After 5
seconds, TV lift will move down slowly and then to the zero
position and then move up 7 mm and stop. The Reset
procedure is complete. During the RESET procedure, you
should hold the RESET button and the LED light on the
handset will blink during the RESET procedure. The LED on
the handset will turn off after finishing the RESET. You can
operate the system now.
10
10
Cont.