4
TEMPERATURE/TIMER CONTROLLER OPERATION SPECIFICATIONS
Start-up:
1. The preset time will ash until the preset temperature is reached.
2. When the control reaches the preset temperature, time display, "Heat On" indicator and program
indicator will stop ashing and the alarm will beep three times.
Temperature:
1. To view the actual temperature, press and hold "Temp Button." Display will read "Lo F" if
temperature is below 273°F and "Hi F" if temperature is above 573°F.
To Program Time and Temperature:
1. Press and hold "Temp" (actual temperature displays).
2. While holding "TEMP," press and hold any program button on the Left PC board for 1 second,
the LED above program lights and display reads "_ _ _ _." Enter the four - digit security code
sequence: 4, 3, 2, 1. Starting with the rst digit, the center horizontal bar will light on each digit
as the security code is entered. The security code will not show on display. Once the correct
sequence has been entered, the preset time will be displayed and the LED for that program will
begin to ash.
3. Set the time with the + or - buttons.
4. Press the "TEMP" button to save the time.
5. The preset temperature will now be displayed.
6. Set the desired temperature for this program using the + or - buttons.
7. Press the "TEMP" button to save temperature and to exit programming mode for this
program. The LED will stop to ash but will remain lit.
8. To stay in program mode without re-entering the security code, press and hold the "TEMP"
button and press the program button that you want to program. The programmed time
for that button will display. Release the "TEMP" button and that program button. Repeat
steps 3 through 8 until programming is nished.
9. While programming a program (LED is ashing), if no input is received for 15 seconds,
the unit will revert to normal operation and the security code must be re-entered.
NOTE: Temperature settings are done with the Left PC board only. The time settings
programmed on the Left PC board will also be programmed onto the Right PC board. See
next column to make changes to the Right PC board only. Each programming change
must be saved by pressing the "TEMP" button!Right PC board (Timer only):
1. To Change the time on Right PC board, press and hold the "TEMP" button on the Left PC
board and press and hold any program button on the Right PC board for one second.
The LED above the program button will light and the Right Display will read "_ _ _ _."
Enter the four-digit security code sequence, 4, 3, 2, 1. Starting with the rst digit, the center
horizontal bar will light on each digit as the security code is entered. The security code will not
show on display. Once the correct sequence has been entered, the preset time will be displayed
and the LED for that program will begin to ash.
2. Set the time with the "+ or -" buttons.
3. Press the "TEMP" button to save the time.
4. The LED will stop to ash but will remain lit.
5. To stay in program mode without re-entering the security code, press and hold the "TEMP"
button and press the program button that you want to program. The programmed time
for that button will display. Release the "TEMP" button and that program button. Repeat
steps 3 through 8 until programming is nished.
6. While programming a program (LED is ashing), if no input is received for 15 seconds,
the unit will revert to normal operation and the security code must be re-entered.
Operation:
1. Press any program button (1-4) on either side to begin the timer countdown for that side. The
LED for the appropriate program will be lit during the countdown and the remaining time will be
displayed. The countdown may be stopped at any time by pressing the same program button.
The display will return to the programmed time of that button.
2. When the display reaches "00:00," the buzzer will sound and the digits will ash.
3. Press the program button to silence the buzzer and return the readout to programmed time.
4. The Right and Left boards will operate independent of each other. Both timers can be in operation
at the same time. The "00:00" display will show which side is timed out.
