Prorack K661 Operation and installation manual

K661
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 2 x 1
x 1 x 2 x 1 x 1
Revision No: 2B 1

Fitting Kit K661
x 1 x 1 x 2 x 2
x 2
2

Fitting Kit K661
MAX kgs (lbs)
W/P WHD
Honda
Civic, 5dr Hatch 12-+ NZ 60 kgs (132 lbs) 60 kgs (132 lbs)
Civic, 5dr Hatch 12-+ AU 60 kgs (132 lbs) 60 kgs (132 lbs)
Civic, 5dr Hatch 12-+ ZA 60 kgs (132 lbs) 60 kgs (132 lbs)
Civic, 5dr Hatch 12-+ EU 60 kgs (132 lbs) 60 kgs (132 lbs)
3

Fitting Kit K661
X
A B C 1 2 3
Civic, 5dr Hatch 12-+ (NZ) -240mm 340mm - 895mm 805mm -
-9 -7/16ths" 13 3/8ths" - 35 1/4ths" 31 11/16ths" -
Civic, 5dr Hatch 12-+ (AU) -240mm 340mm - 895mm 805mm -
-9 -7/16ths" 13 3/8ths" - 35 1/4ths" 31 11/16ths" -
Civic, 5dr Hatch 12-+ (ZA) -240mm 340mm - 895mm 805mm -
-9 -7/16ths" 13 3/8ths" - 35 1/4ths" 31 11/16ths" -
Civic, 5dr Hatch 12-+ (EU) -240mm 340mm - 895mm 805mm -
-9 -7/16ths" 13 3/8ths" - 35 1/4ths" 31 11/16ths" -
4

Fitting Kit EN
K661
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
5

Fitting Kit EN
K661
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
6

Fitting Kit EN
K661
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A = Clear
B = Grey
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = A073
B = A074
C = A075
7

Fitting Kit EN
K661
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
8

Fitting Kit EN
K661
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-252
B = 11-04-253
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
9

Fitting Kit EN
K661
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
10