Proscend 708EP-AC User manual

708EP-AC 8-Port PoE Long Reach
Switch/Extender
Quick Installation Guide Version: 1.00
The 708EP-AC PoE Switch/Extender features 8 pairs of Long Reach
Ethernet connections in cooperation with the 101EPI. Each pair carries
Ethernet traffic and power over an Ethernet cable up to 800 meters. The
708EP-AC is designed to locate at network side where the 101EPI is
located at the remote side.
Overview
LED Indicators
Each LED indicator on the front panel is described in the following table.
LINE Port Pin Assignment
Use the included power cord to connect the power socket on the front panel
to a power outlet.
To prevent the effects of noise from electromagnetic interference (EMI), run
the ground connection from the ground screw to the grounding surface
before connecting the devices.
Connecting Power
Ground Connection
Reset button allows you to reboot the unit or restore to factory default
setting.
Reset Button
The PoE pinouts of the LINE interfaces are as below when 8 wires are
connected.
Description
V+
V+
V-
V+
Pin
1
2
3
4
PoE Pinouts
Description
V+
V-
V-
V-
Pin
5
6
7
8
The PoE pinouts of the LINE interfaces are as below when 4 wires are
connected.
Description
V+
V+
V-
Not used
Pin
1
2
3
4
PoE Pinouts
Description
Not used
V-
Not used
Not used
Pin
5
6
7
8
Description
TX+
TX-
RX+
Not used
Not used
RX-
Not used
Not used
Description
RX+
RX-
TX+
Not used
Not used
TX-
Not used
Not used
Pin
1
2
3
4
5
6
7
8
Pin
1
2
3
4
5
6
7
8
MDI Port Pinouts MDI-X Port Pinouts
Reboot
Restore to factory default setting
Press the button for 1 second
Press the button for more than 5 seconds
Function Operation
The LINE interfaces of the 708EP-AC are standard 8-pin
RJ45 connectors. The following tables display the pinouts.
1 8
8-pin RJ45
Color Description
Device Power On.
Device Power Off.
System is working.
System is off.
Device Error.
Powered Device Connected.
Powered Device Disconnected.
1000Mbps UPLINK LINK UP.
1000Mbps UPLINK LINK DOWN.
1000Mbps Data Transmitting.
100/10Mbps UPLINK LINK UP.
100/10Mbps UPLINK LINK DOWN.
100/10Mbps Data Transmitting.
100Mbps LINE LINK UP.
LINE LINK DOWN.
100Mbps Data Transmitting.
10Mbps LINE LINK UP.
LINE LINK DOWN.
10Mbps Data Transmitting.
LED LED
On
Off
On
Off
Blinking
On
Off
On
Off
Blinking
On
Off
Blinking
On
Off
Blinking
On
Off
Blinking
PWR
SYS
PoE1~8
UPLINK
LINE 1~8
Green
Green
Green
Green
Green
Yellow
Yellow
- 1 -
Proscend Communications Inc. All rights reserved. www.proscend.com

Rack Mounting
(1) Access the Web Configurator via UPLINK port or LINE ports.
STEP 1: Enter the default IP address 192.168.1.1 as URL in your web
browser.
STEP 2: Please enter the default username root and the default
password 2wsx#EDC.
STEP 3: Click Login button.
(2) Change the default password.
Go to User setting and reset your new password and then click Apply
button.
NOTE: The default password should be changed after configuration. Please avoid using easy to
guess passwords (e.g., root, 1234...).
Setup
STEP 1: Align two brackets with the holes on the sides of the Switch and
fasten the mounting kits by using screws.
NOTE: The type of screw is flat head M3 x 5mm.
STEP 2: After attaching two brackets, line up the rack-mounting positions
of the holes in the brackets with the appropriate holes on the rack
and then fasten the Switch on the rack by using screws.
NOTE: The rack-mounting screws are not included in the package.
NOTE
󱾁Please scan below QR Code to download online resources.
Download Link: https://www.proscend.com/en/product/708E.html
708EP-AC
ATTENTION: Safety Warning
󱾁Disconnect all power from devices before attempting installation.
󱾁This device is intended for installation only in restricted access locations as defined where both
these conditions apply:
・Access is through the use of a lock or tool and key, or other means of security, and is controlled
by the authority responsible for the location.
・Access can only be gained by service persons or by users who have been instructed about the
reasons for the restrictions applied to the location and about any precautions that shall be
taken.
󱾁All electric installations must be carried out in accordance with local and national regulations.
󱾁Do not work on the system, connect or disconnect cables during periods of lightning activity.
󱾁The equipment must be connected to earth.
󱾁Shield of RJ45 cables has to be connected to the same earth potential as the equipment.
󱾁Please remove the ground connection lastly if you need to remove the device after installation.
󱾁If the LINE interface is used for the connection between two buildings, all necessary protective
measures must be ensured externally.
󱾁This equipment relies on the building’s installation for short-circuit (overcurrent) protection. Ensure
that a fuse or circuit breaker no larger than 3.5 is used.
- 2 -
Proscend Communications Inc. All rights reserved. www.proscend.com
P/N:604040000076