Protech Systems KF-7270 User manual

If you discover any item below damaged or lost,
please contact your vendor.
This Quick Reference Guide x1
KF-7270
Quick
Reference
Guide
This Quick Reference Guide x1
Ver. Q1
All Rights Reserved. Copyright 2018
Packing Checklist
KF-7270
KF-7270 KF-7270
Specifications
System View
KF-7270 Kiosk Main Unit X1
AD Board X1
17” Bezel free P-CAP
Touchscreen
AD Board
RFID Sensor
IC Card Reader
Thermal Printer
Barcode Reader
DM Tray
Speaker
Speaker
Door
System
CPU Type Intel®CoreTM i5-6500 3.20GHz Processor
Chipset Intel®H110 Chipset
Memory Support 2 x DDR4 SO-DIMM sockets (Default: 4GB)
HDD 1 x Intel 2.5" 128GB TLC SSD
Network 10/100/1000 Mbps Base-T Fast Ethernet (RJ45)
Power Supply AC 100-240V, 50-60Hz
System Weight About 83kg (with package)
Dimensions (WxHxD) 527 x 1788 x 412mm
O.S. Support Windows 10 IoT Enterprise LTSB 2016 32bits
Fan 2 x system fans
Material SPCC, SECC
Speaker 2 x 2W HD speaker
Painting Powder-paint coating
Operating Display
Touch 17” Bezel free P-CAP Touch (USB interface)
LCD 17" (4:3) LED backlight
Max. Resolution 1280 x 1024
Brightness 350 cd/m²
Touchscreen Projected Capacitive Touch
Viewing Angle Horizontal: (R) 85°/(L) 85° / Vertical: (U) 80°/(L) 80°
Estimated luminance lifetime 50,000h
Integrated Devices
Thermal Printer Epson TM-T70II
Barcode Reader FS5002J
IC讀卡機 SKH301-1000C
悠遊卡機 虹堡TS-2000
Environment
Operating Temp. 5°C~ 35°C (41°F ~ 95°F)
Storage Temp. 0°C~ 60°C (32°F~ 140°F)
Humidity 20%~ 85%
If you discover any item below are damaged
or lost, please contact your vendor.
AC Power Cord Cable X1
Panel Key X2
Door Key X2
2ND D Screw Cover X1

Quick Setup
KF-7270
All Rights Reserved. Copyright 2018
Safety Precaution
17” Self-Service Kiosk with P-Cap Touch
Step 1.
Connect the AC power cord to the AC power jack,
connect the Ethernet cable to the LAN port, and
connect the COM cable to the COM1 port.
Step 2.
Use your hand to release the screw on the printer door and open it.
• Don’t allow foreign objects to fall into this product.
• If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry
cloth.
• Never use strong agents such as benzene and thinner to clean the system.
If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and
then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special made vacuum cleaner
for computers.
• Don’t contact the surface of capacitive touch before entering your operation system, or capacitive
touch may have position problems for electrostatics interface.
• Don't exchange the M/B battery by yourself or serious damage may incur.
The following messages are reminders for safety on how to protect your system from damages and
extend a long system life.
1. Check the Cable Voltage
• Make sure the range of operating voltage between AC 100~240V. Otherwise, the system could be
damaged.
2. Environmental Conditions
• Place your KF-7270 on a sturdy, level surface. Be sure to allow enough space to have easy
access around the system.
• Avoid extremely hot or cold place to install the system.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the system from any heating device or using it outdoors in a cold winter day.
• Bear in mind that the operating ambient temperature is from 5°C~35°C (41°F~95°F).
• Avoid moving the system rapidly from a hot place to a cold one and vice versa for condensation
may come from inside of the system.
• Place KF-7270 in strong vibration(s) may cause hard disk failure.
• Don’t place the system close to any radio active device in case of signal interference.
3. Handling
• If the system isn’t fully in DOS mode, adjust BIOS setting as the instruction:
Advanced Chipset Feature →Boot display →choose “LFP”.
• Avoid putting heavy objects on top of the system.
• Don’t turn the system upside down. This may cause the hard drive to malfunction.
2Use your hand to
release the screw and
open the printer door.
Printer Door
Step 3.
Press the Power button to turn on the system. The Power
Button is hidden inside on the upper right area above the
printer door.
3Press the Power button.
Note: The Power Button is
hidden inside on the
upper right area above
the printer door.
LAN
Port
COM1
Port
AC Power
Jack
1Connect AC power cord,
Ethernet cable and COM cable.