All Rights Reserved. Copyright 2017
Unit: mm
The following messages are reminders for safety on how to protect your system from damages and to extend a long life of the system.
1. Check the Cable Voltage
• The range of operating voltage should be between DC 9V and 36V. Otherwise, the system could be damaged.
2. Environmental Conditions
• Place your KS-1132 on a sturdy, level surface. Be sure to allow enough space to have easy access around the system.
• Avoid extremely hot or cold place to install the system.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the system from any heating device or using KS-1132 when it’s been left outdoors in a cold winter day.
• Bear in mind that the operating ambient temperature is from 0°C ~ 35°C (32°F ~ 95°F).
• Avoid moving the system rapidly from a hot place to a cold place and vice versa because condensation may come from inside of the system.
• Placing KS-1132 in strong vigrations may cause hard disk failure.
• Don’t place the system close to any radio-active device in case of signal interference.
3. Handling
• Avoid putting heavy objects on top of the system.
• Do not turn the system upside down. This may cuase the hard drive to mal-function.
• If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry cloth.
• Never use strong agents such as benzene and thinner to clean the system.
• If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special made vacuum cleaner for computers.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore we strongly recommend that qualified engineers can open and disassemble the system.
Please handle LCD and Touchscreen with extra care as they are easily breakable.
Safety Precaution
Easy Maintenance
Jumper Setting
CAUTION! Danger of explosion may occur if the battery is replaced incorrectly. Replace batteries only with the same or equivalent type recommended
by the manufacturer. Dispose the used batteries according to the manufacturer’s instructions.
Note: H9N SKU has no LVDS connector/jumper setting & M.2 slot.
JHDD_PWR2
JUSB2
JHDD_PWR1
JP1 VCCIO Voltage Selection
0.95V 1.0V
(default)
1
1
JP16 AT / ATX Mode
Selection
ATX
(default)
1
AT
1
1
Normal
1
(default)
Clear CMOS
JCMOS1 Clear CMOS
Data Selection
JP5 LVDS Control
Selection
LVDS Enable
(default)
1
Disabled
1
JP6 COM1 RS232/422/485
Selection
RS485
RS422
RS232
12
9
10
(default)
2
10
1
9
2
910
1
JP11 COM1 RS-485 Auto
Flow Control Selection
(default)
Disable Enable
1
1
JP17 Backlight PWM Level
Selection
1
(default)
1
5V 3.3V
ATX
JP2 AT / ATX Mode
Selection
(default)
1
AT
1
CPU_FAN1
CPU1
M1
4
12V
12V
GND
AUDIO1
LAN2_USB2
LAN1_USB1 VGA1
DP1 ATX_PWR1
GND
3 4
1 2
1
JP16
JP6
JP11
11
10
9
JP_COM2 6
5
1
2
1 2
5 6
JP9
1
PCI_E1
1
JCMOS1
1 1
JP2
JP17
1
9
2
FP1
JUSB1
1
M_2_SSD
JP1
SO-DIMM1
SO-DIMM2
JP9 SPI Override Protection
Enable
(default)
1
Disable
12
1
RI
(default)
5
6
12V
COM2 Pin9 Voltage
Selection
2
1
5V
2
15
6
5
6
RI(default)
21
5 6
12V
5V
21
5 6 6
5
2
1
COM1 Pin9 Voltage
Selection
Intel
®
H110
JLVDS1
1
2930
2
COM2
COM1
M.2 SSD
DC_IN
JDIO1
1615
21
JP13
JP15
JP14
2 1
56
2 1
56
2 1
56
17
SATA2
17
SATA1
1
1
1
9
210
1
9
210
1 2
10
SYS_FAN1
1
JP7
1
JP5
INV1
6
1
JPWR_DIO1
1
1
4
JP12
JP10
1JP_COM1
SP1
(Buzzer)
Battery
1
JP15 LVDS Voltage
Selection
(default)5V
5
1
6
2
3.3V
5
1
6
2
JP13/JP14 LVDS Voltage
Selection
5
1
6
2
JP13
5
1
6
2
JP14
1024x768
Channel S/8bit
(default)
6
2
5
1
6
2
5
1
JP13 JP14
1920x1200
Channel D/8bit
M/B: BM-2503
Removing Front Panel
Step 1. Press the main door latch to unlock the
system front door.
Step 3. From the same location in Step 2,
remove the 6 screw nuts as shown:
Step 4. Lift up to remove the panel from the system.
Removing Stand
Installing Wall Mount
Step 3. Attach the system over the wall (Diagram 1) and precisely align
and insert the 8 screw caps located on the rear of the system into
the corresponding mounting holes on the installed wall mount
brackets (Diagram 2).
Step 2. Align the screw holes on both sides of the provide wall
mount brackets with the drilled holes on the wall, and
install the eight sleeve anchors to secure the two wall
mount brackets firmly.
Step 1. Press the main door latch to unlock the
system front door.
Step 3. Close the system front door.
Step 2. Gently pull down the front door and remove the
8 screw nuts as shown:
Step 4. Lift up to detach the system from the Stand.
Step 4. Press the main door latch to release the system front door. Step 6. Close the system front door to complete the installation.Step 5. Fasten the screw (M4x12L) provided into the location
to secure firmly.
Press the main door
latch to unlock.
Lift up to remove the panel.
x 6
Release the six screw nuts.
Press the main door
latch to unlock.
Close the Front Door.
Pull down the
front door.
x 8
Release the eight screw nuts.
Lift up the system
to detach.
Pull down the
front door.
Press the main door
latch to unlock.
Insert the screw
(M4x12L).
Close the Front Door.
Step 2. Gently pull down the front door and remove the
two screws as shown. The door latch can be
then detached.
The spring previously attached on
the door latch is loosened.
Door Latch
Pull down the
front door.
Wall
Fasten the 8 screws
to secure the two
wall mount brackets
on the wall.
Diagram 2
mounting
hole
Wall
Wall Mount
Bracket
Rear of the
system Diagram 1
Insert the 8 screw caps into
the corresponding mounting
holes.
screw
caps
Step 1. Precisely drill 8 screw holes on the wall according to the
dimensions and distances as specified for the installation of
the provided 8 x sleeve anchors (1/4”) in the next step.
Sleeve Anchor 1/4” (8 pcs)
244
70
8
678 mm857 mm
Wall
Ø
Unit: mm
Floor
