Jumper Setting
KS-1130
Self-Service Payment Kisok
All Rights Reserved. Copyright 2018
Safety Precaution
JP3 Clear CMOS Data
Selection
Normal Clear
CMOS
(default)
11
Battery
1
5
ESATA1 DRW1
COM2
PWR_IN1
VGA1
LAN1 USB8 LINE-OUT1
SW1_2
LED1_2
SPK2
JP5
DC5V_PWR1
JP33
JP35
JP34
JINV3
PS/2_1
SW1
JP46
USB6
JI_BUTTON1
PS/2_2
JINV2
JP1
SLOT1
J3USB7LED1_4LVDS1
JP_VDD1
JP15
JP14
JP12
JP8
JP9
JP19
USB1
JINVDRV1
JP3
JP4
LED1_1
BAT1
JP39
SATA2
SATA1
JPWR_4P2
JPWR_4P1
JP_COM2
JP_COM3
JP_COM4
JP_COM1
LPT1
COM3_1
COM2_1
CPU_FAN1
PRT_PWR1
DC12V_PWR1
COM4_1
COM1_1
USB2 JP37
JP29
DIMM1
COM3
1
1
1
1
1
1
1
16
6
1
1
1
5
1
6
1
TOUCH2COM4_2
1
11
SPK1
1
JP20
JP21
JP22
1
1
6
5
10
11517 51
52
18
16
2
1
1
1
1
11 1
1
5
6
2
2
129
30
1
1
1
1
1
2
9
10
1
1
1
1
1
17
14
141
7
1
1
1
1
1
5
1
1
6
6
1
14
13
26
1
1
6
6
11
1
1
1
274
72
71 73
204
203
Intel®
Celeron®J1900
Quad-Core
1
1
1
111
SP1
1
JP38
SW1_1 1
TOUCH1
1
5
Caution:
1.The voltage of external COM2
& COM3 ports can be
controlled on BIOS for your
convenience.
The corresponding jumpers
JP_COM2 & JP_COM3 are
set open (no connection) by
default. Refer to the Voltage
Adjustment Configuration
section (BIOS default: RI).
2.JP_COM2 & JP_COM3 can
be enabled when COM2 &
COM3 voltage adjustment is
disabled on BIOS.
3.The voltage of COM port is
adjustable by BIOS or jumpers.
You can select to adjust the
voltage of COM ports either
through BIOS or by setting
jumpers. DO NOT use these
two methods at the same time
in case of system error,
component damage or serious
boot failure.
COM Port RI & Voltage
Selection
RI
1
2
5
6
12V
5V
6
5
2
1
1
2
5
6
(default for
JP_COM2 & JP_COM3)
1
2
5
6
Open
(JP_COM1/2/3/4)
(default for
JP_COM1 & JP_COM4)
CAUTION! Danger of explosion may occur if the battery is replaced incorrectly. Replace batteries only with the same or equivalent type recommended by the manufacturer. Dispose the used batteries according to the manufacturer’s instructions.
• Don’t allow foreign objects to fall into this product.
• If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
• When the outside of the case is stained, remove the stain with a neutral washing agent with a dry
cloth.
• Never use strong agents such as benzene and thinner to clean the system.
If heavy stains are present, moisten a cloth with diluted neutral washing agent or with alcohol and
then wipe thoroughly with a dry cloth.
• If dust has been accumulated on the outside, remove it by using a special made vacuum cleaner
for computers.
• Don’t contact the surface of capacitive touch before entering your operation system, or capacitive
touch may have position problems for electrostatics interface.
• Don't exchange the M/B battery by yourself or serious damage may incur.
The following messages are reminders for safety on how to protect your systems from damages and to
extend a long life of the system.
1. Check the Cable Voltage
• Make sure the range of operating voltage between AC 100V ~ 240V. Otherwise, the system could
be damaged.
2. Environmental Conditions
• Place your KS-1130 on a sturdy, level surface. Be sure to allow enough space to have easy access
around the system.
• Avoid extremely hot or cold place to install the system.
• Avoid exposure to sunlight for a long period of time or in an airtight space.
• Avoid the system from any heating device or using it outdoors in a cold winter day.
• Bear in mind that the operating ambient temperature is from 0 ~ 35°C (32 ~ 95°F).
• Avoid moving the system rapidly from a hot place to a cold place and vice versa because
condensation may come from inside of the system.
• Place KS-1130 in strong vibration(s) may cause hard disk failure.
• Don’t place the system close to any radio active device in case of signal interference.
3. Handling
• If the system isn’t fully in DOS mode, adjust BIOS setting as the instruction:
Advanced Chipset Feature => Boot display => choose “LFP”.
• Avoid putting heavy objects on top of the system.
• Don’t turn the system upside down. This may cause the hard drive to malfunction.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And therefore we strongly
recommend that qualified engineers can open and disassemble the system. The LCD and Touchscreen are
easily breakable, please handle them with extra care.
