Protech Systems BM-0947 User manual

USER’S
MANUAL
B
M
-
0
9
4
7
Mini-ITX Motherboard
with Intel
®
4
th
Gen. Core i7/i5
features LA /VGA/8USB/6COM
B
M
-
0
9
4
7
M
1

BM-0947
With Intel® 4th Gen. Core 


Mini-ITX Motherboard
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the property of their
respective owners.
This manual is copyrighted in September 2014. You may not reproduce or transmit
in any form or by any means, electronic, or mechanical, including photocopying
and recording.
DISCLAIMER
This operation manual is meant to assist both Embedded Computer manufacturers
and end users in installing and setting up the system. The information contained in
this document is subject to change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void your
authority to operate such equipment.
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.

Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual…............................................................
1-2
1-2 System Specification…..........................................................
1-3
1-3 Safety Precautions….............................................................
1-5
CHAPTER 2 HARDWARE CONFIGURATION
2-1 Jumper & Connector Quick Reference Table…....................
2-2
2-2 Component Locations….…...................................................
2-3
2-3 How to Set Jumpers…...........................................................
2-5
2-4 COM Port…………………………………………………...
2-7
2-5 COM Connector…………………………………………….
2-8
2-6 VGA Port…………………………………………………...
2-8
2-7 Keyboard & Mouse Port…..………………..........................
2-9
2-8 LAN & USB3.0 Port...……………………………………...
2-10
2-9 Audio Jack…………………………………………………..
2-11
2-10 USB2.0 Port….……………………………………………..
2-12
2-11 COM Port RI & Voltage Selection…………………………
2-12
2-12 COM2 RS-232/422/485 Selection………………………….
2-13
2-13 COM2 Auto-detect Selection……………………………….
2-13
2-14 Front Panel Connector & Selection………………………...
2-14
2-15 Intel
®
ME Selection…………………………………………
2-15
2-16 Clear CMOS Data Selection………………………………..
2-16
2-17 BIOS Recovery Mode Selection……………………………
2-16
2-18 Fan Connector………………………………………............
2-17
2-19 SATA Connector……………………………………………
2-17
2-20 USB2.0 Port….……………………………………………..
2-18
2-21 ATX Power Connector……………………………………...
2-19
2-22 LVDS Connector……………………………………............
2-20
2-23 LVDS Voltage Selection…….……………………………...
2-21
2-24 LCD Backlight Connector..….……………………………...
2-21

Contents
CHAPTER 3 SOFTWARE UTILITIES
3-1 Introduction……………..........................................….........
3-2
3-2 Intel
®
Chipset Software Installation Utility……..……..…...
3-4
3-4 Intel
®
USB3.0 eXtensible Host Controller Utility………….
3-5
3-5 Intel
®
Management Engine Components Utillity…………...
3-6
3-6 VGA Driver Utility………………………………….……...
3-7
3-7 LAN Driver Utility……...........................................….........
3-8
3-8 Sound Driver Utility………………………………………..
3-9
CHAPTER 4 BIOS SETUP
4-1 Introduction….......................................................................
4-2
4-2 Entering Setup…...................................................................
4-4
4-3 Main…………......................................................................
4-6
4-4 Advanced…...........................................................................
4-7
4-5 Chipset…...............................................................................
4-24
4-6 Boot……...............................................................................
4-34
4-7 Security…..............................................................................
4-39
4-8 Save & Exit….......................................................................
4-42
APPENDIX A EXPANSION BUS
PCIe Bus………………………………….......................................
A-2
APPENDIX B TECHNICAL SUMMARY
Block Diagram…..............................................................................
B-2
Interrupt Map…................................................................................
B-3
DMA Channels Map….....................................................................
B-8
I/O Map…........................................................................................
B-9
Memory Map….……………………………………………………
B-12
Watchdog Timer Configuration….………………...………………
B-14
Flash BIOS Update…...............................................…....................
B-17

Page:1-1
INTRODUCTION
This chapter gives you the information for BM-0947. It also outlines
the system specifications.
Sections included:
About This Manual
System Specifications
Safety Precautions
Experienced users can jump to chapter 2 on page 2-1
for a quick start.
CHAPTER
1

Chapter 1 Introduction
BM-0947 USER ′ S MANUAL Page: 1-2
1-1. ABOUT THIS MANUAL
Thank you for purchasing our BM-0947 Mini-ITX Motherboard with Intel
®
4
th
Gen. Corei7/i5 processor, enhanced with LAN, VGA, 8 USB & 6COM, which
is fully PC/AT compatible. The BM-0947 provides faster processing speed,
greater expandability and can handle more tasks than before. This manual is
designed to assist you how to install and set up the system. It contains four
chapters. The user can apply this manual for configuration according to the
following chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specifications for this system. The final page of this chapter will indicate how to
avoid damaging this board.
Chapter 2 Hardware Configuration
This chapter outlines the component locations and their functions. In the end of
this chapter, you will learn how to set jumper and how to configure this card to
meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the VGA
utility, LAN utility, Sound utility, and Flash BIOS Update. It also describes the
Watchdog-timer configuration.
Chapter 4 BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A Expansion Bus
This appendix introduces you the expansion bus for PCIe connectors.
Appendix B Technical Summary
This appendix gives you the information about the Technical maps.

Chapter 1 Introduction
BM-0947 USER ′ S MANUAL Page: 1-3
1-2. SYSTEM SPECIFICATIONS
System
CPU Intel
®
4
th
Gen. Corei5/i7 Processor (LGA1150)
i5-4570S (65W)
i5-4570TE (35W)
i7-4770S (65W)
OS Support Windows 8, 7
Chipset Intel
®
H81
Memory 2 x SO-DIMM (204 pins), dual channel DDR3-1333/1600
MHz, up to 16GB
BIOS AMI
Watchdog 1~255 seconds
Power Supply ATX 12V & 5VSB (24-pin connector; 4-pin connector for
CPU)
Dimension 170 x 170 mm (6.69” x 6.69”)
Certificate CE/FCC
I/O Ports
Serial Port 6 ports:
COM1/2: COM1 & COM2 D-sub, both COM1 & COM2
are 5V/12V/RI selectable
COM3/4/6: Box headers on board
(COM1/3/4/5/6 for RS-232, COM2 for RS-232/422/485)
USB Port 2 x external USB 3.0, stacked with LAN
6 x USB 2.0 (2 are external ports, 4 are internal pin-
headers.)
SATA Interface Intel
®
H81: 1 x SATA II, 2 x SATA III
2 x SATA III
LAN 1 port, supports Wake-on-LAN
LAN1: Intel
®
I217-LM/V
Audio Realtek ALC888S-VD2-GR High Definition audio codec
Line-in/Line-out/MIC
Option: S/PDIF
Keyboard/Mouse 1 x PS/2
Expansion Bus 1 x PCIe (16x) Gen. 2

Chapter 1 Introduction
BM-0947 USER ′ S MANUAL Page: 1-4
Display
Graphics Built-in processor to share the system memory.
1 x VGA
1 x LVDS (2CH 18/24 bits)
Environment
Operating Temp. 0 ~ 60°C (32 ~ 140°F)
Storage Temp. -40 ~ 80°C (-40 ~ 176°F)
Humidity Operating: 5~90% (non-condensing)

Chapter 1 Introduction
BM-0947 USER ′ S MANUAL Page: 1-5
1-3. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Keep your system away from static electricity on all occasions.
2. Prevent electric shock. Don‘t touch any components of this card when the card is
power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices.
For instance, when you connect a jumper or install any cards, a surge of power
may damage the electronic components or the whole system.

Page 2-1
HARDWARE
CONFIGURATION
** QUICK START **
CHAPTER
2
Helpful information describes the jumper & connector settings, and
component locations.
Sections included:
Jumper & Connector Quick Reference Table
Component Locations
Configuration and Jumper settings
Connector’s Pin Assignments

Chapter 2 Hardware Configuration
BM-0947 USER ′ S MANUAL Page: 2-2
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
JUMPER/CONNECTOR NAME
COM Port COM1, COM2, COM5
COM Connector COM3, COM4, COM6
VGA Port VGA1
Keyboard & Mouse Port KB_MS1
LAN & USB3.0 Port LAN1_USB1
Audio Jack AUDIO1
COM Port RI & Voltage Selection JPCOM1, JPCOM2
COM2 RS-232/422/485 Selection JP8
COM2 Auto-detect Selection JP7
Front Panel Connector & Selection FP1
Intel®ME Selection JP3
Clear CMOS Data Selection JP4
BIOS Recovery Mode Selection JP1
Fan Connector CPU_FAN1, SYS_FAN1, SYS_FAN2
SATA Connector SATA1, SATA2, SATA3
USB2.0 Port JUSB2, USB3, USB4
ATX Power Connector ATX_PWR1, ATX_PWR2
LVDS Connector LVDS1
LVDS Voltage Selection JP15
LCD Backlight Connector JINV1

Chapter 2 Hardware Configuration
BM-0947 USER ′ S MANUAL Page: 2-3
2-2. COMPONENT LOCATIONS
AUDIO1
JP4
JP1
JP3
FP1
SATA3 DIMM2
DIMM1
CPU_ FAN1
SATA2
SATA1
SYS_FAN1
JP6
SP1
USB3
USB4
JP15
JD09M1
JPCOM1
JPCOM2
COM3 COM4
JP7
JP8
ATX_PWR2
ATX_PWR1
SYS_
F
AN2
KB_MS1
LAN1_USB1 JUSB2
LVDS1
COM6
VGA1+COM5
REMOVE
Intel®4th Gen.
Core™ i5/i7
(LGA1150)
Intel®
H81/Q87
JLPC1
9
10
1
2
1
1
1
Battery
1
2
7
8
1
2
5
6
1
4
1
4
17
17
17
12 11
2
1
1
2
71
72
73
74
203
204
1
2
71
72
73
74
203
204
1
2412
3
4
1
2
1
3
2
6 5
1
5
2
1
1
5
616
10
1
2
9
10
1
2
9
10
9
102
1
1
30
291
2
5 10
1 6
8
JINV1
1
PCI_E1
BM-0947 Front Connector, Jumper and Component locations

Chapter 2 Hardware Configuration
BM-0947 USER ′ S MANUAL Page: 2-4
R133
R1094
V6
CM17
CB7
R367
CB77
R378
R380
C241
C64
C55
R708
R750
R728
R735R739
C383
R126
C238
C236
C237
C235
R379
R385
R376
R375
CB6
C246
CM2
U49
R129
R382 R383 C240
R729
U19
V7
R695
C301
C221
C220
C216
C217
R855R854
C410
R845
U41
U43
TP113
R1096
TP125 U45
U46
R1007
R1008
C479
R687R686
Q45
Q48
R697
CE25
C219
C218
C214
C215
R277
R864
R841
R860
R842
Q97
TP152
R863
TP115TP108TP141
TP140
TP151
R846
TP122TP107
CB74
R1081
R1080
CB75 U42
CB76
TP112
R1087
R1085
C148
D2
TP111
TP123 TP121
C137
R733
C146
R738
R1009
C482
U55
R1001
R1003
C478
C308
R397 R400
L2
R1116
Q146
R1110
Q145
R1113
TP129
TP142
R280 R273
TP143
C154
TP145 TP146
TP147
TP148
C152
R138
CB4
CM13
R105
C114
C147
C164
C141
C142
C150
C139
C153
TP95
R114 R217
R999
R1006
Q118
R995
Q117
U36
Q115
CD13
R398 R402
R405 R406
L4 L3
Q144
R1111
R1105
R852 R849
R1117
C117
C118
FB2
C159
Y2
R283
C110
TP106
TP105
TP138
TP139
R285
R139 C161
R284
R141
R140
C562
C566
C160
C158 C157
C133
TP91
TP90
R100 R227
R91
R233
TP98
TP97
R161
C123
Q119
Q116
Q114
R1019
C225
C493
R1107
CB80
R1115
R1108
R853
Q96
C407
R861
C130
C406
C111
R137
C115
TP86
TP118
R103
R101
R112
R251
R246
TP76 TP75 R121
R204 R208 R202 R102
TP77
TP114
R770R772
C392
R998 R996 C470
R771
C477
R521
R522
C361
C362
C349 C347
FB23
C327
R1017
C488
C354
R1018
Q123
C489
C490
R1112
R1109
C578
R1114
Q95
R848 C405
R271
C151
TP128
TP127
TP87TP124
TP133
C162
C149
TP119
R241R136
R238 R110
R243
C390
R768
R767
R769
C291
C292
R438
R439
C328
C333
U38
R1106
Q94
C492
R302
R272
R859
R856
R851
R288
C116
C163
R230
C126
C140
TP99
R232
R248 R231
R213
R235 R245
R193
R764
R766
C389
Q68
U28
C391
CE5
CB9
FS12
CE28
C496
C491
R866
R867 R865
C408
C612 C611
TP117
TP116
C138
C136
TP110
TP120
TP109
R247 C109 C107
C108
C106
R221
R218
R183 R179
R836
R829
U54
U27
JAPS1
CB8
CB78
R374
R370
C230
C229
C239
C343
C338
R858 R869 R847 R857
U39
R850 R862 CB59 C409
R868 Q100
R705
R703
R700
Q99
R702
R1169 R1168
C380
R1163
R1170
R1162
R760
R1172
TP80
C156
C614 C613
C135
C144
R261
C165
R306
R205
R203
C105
C104
R826
R762
R765
CM46
R513
CB79
R514
R1024 C337
R715
CB56
R757
R1173
R1171
Q66
R758R759
Q8
R267
C143
R832
R216 R226 R225
C393
R833
R827
Q86
R763
R779
R775
C388
R730
R740
R736
C384
R731
U50
R368
R366
U6
CM21
CM20
U9
R1023 R1029
R707 R701
CB54
R710
Q51
R749
R746 R743
Q67
Q43
R683 R682 R680
R156
R90
R278
R116
R279
R113
R185
R184
R99
R780 C394
R774 R778
Q69
R783
R776
R777
C404
C403
R834
D17
CM14
R388
R387
CM47
CM1
R711
R712
R716
R704
R706
R714
R699
CB55
CB53
R713
R709
U23
R744 R747 R752
R751R755
Q65
R754
C386
R753
R672 R674
Q41
R678 R676
Q70
R773
U57
R781
R784 R782
R837
Q90R835
R130
U15
CB84
R597
R592 R600 R601
R593
R596 R599 R598
FS18
R615
R605
R594 R602
C553
R803
C552
R825 R823 R824
U53
V1
CB39
R927
R879 C411
R905
R913
R888
C423
C415
R44
R43
R46 R22
R20
C500
R811
R813
R814
R820
R810
R822
R821
R804
R808
Q79
C397
R816
R812
C399 U16
R873R870
R882
R880
R894
R902
R55
R1090
R56
R1059
R1060
C577CB66
R1061
C549 C550
Q130
U52
R807
R805
C400
R874
R907
R918
R910
R891
R899
R901
R13
R47
R42
R41
R38
R30
R34
R53
CB72
R1062
R815 R802
R806R809
C20 Q80
R73
R74
C398
Q83
R817
R819
R818
R908
R11
R37
R36
R18
R32
R72
R1091
C27
R954
R955
TP15 TP13
TP18
TP74
TP56
TP69 TP45
TP16 TP68
R71 R70
C21
TP11
TP12 TP22
TP49TP48TP46
C44
C40
C41
C2
C45
D11
R956
R1122
R957
C85
C80
R1123 R1124
R949 R948
C42
C32
C49
C83
C54
C6
C22
C8
C9
U31
R545 R548 R547
C53
C43
C51
C30 C29
C79
C7
C48
C52
C5
C47
TP135
TP150
TP136
R945
R952
R1067 R1068
CB19
CB81
TP27
TP71
C82
C84
C31
C25 C26
C23
C24
C81
C13
C50
TP149
TP137
C439
C443
R1071 R1072 R1070 R1073
TP26
TP72
TP23
R75
R76
R67 C37
R69
C14
R68
TP2
TP31
TP30TP73 TP24
TP53
C36
R77
R965
R964
R972
R973
TP51TP1
TP52
TP43
TP42
TP41
TP50
TP19
TP40
R1179
C453
C3
TP100
R269
R151 R150
R756
R178
R236
R160
R122
R120
C132
C10
R145
R152
C33
R1189
R1180 R1178
R86
R307
C35
R1182
R83
R144
R460
R840
R838
TP134
C4
R63 R64 R62
C385
R175
R761
R155
R154
C387
R134
R253
R176
U5
R453
R843
R844
Q91
R66
R1083
R1088
R1084
C11
C34
Q7
R308
R1185
R309
R158
R839
Q92
Q98
R65
Q93
R1082
R1097
Q141
R732
R727
R741
R737
R734
R742
R1005
R1002
R1004
R692
R691
Q46
B E
C
1
2
24
A2
A82
A81
1
2
12
21
A1
B1 B2
B81 B82
1
2
6
1
4
3
6
1
4 3
1
7
2
8
4
1
2
22
32
42
36
1
2
1
B
6
C
1
C
E B
2
E
1
B E
C
C C
B E B
6
1
11
6 4
3
1
12
4
3
CB
EE
4
3
B 6 4
3
1
E
5
1
48
5
4
E
C
E B
C D
B G S
C
1
2
B 1
E
6
11
12
1
1
1
1
8
8
1
C
E BC
E B
E
C
1
3
7
7
7
5
25
35
44
8
1
9
10
A4
B4
C
B
E
B E
CB
E
C
3
2
3
4
2
1
1211
2
3
CB
1
2
CB
4
1
18
8
B
E
C
CB
E
4
1
CB
E E
5
1
8
B
E
C
8
1
8
E
C
B
E
B
S
G
8
G
S
64
3
1
64
3
1
C
B
E
B
E
B
E
8 8
1
2
3
1
64
1
CE
B
1
D
C
8
C
G
S
C
D
1 1 1
D
B
E
C
33
32
128
3
1
2
8
1
97
1
96
65
64
E
CB
E
S
B
C
1
10
24
2 1
9 1
34
13
41
3
1
8
12
1
8
12
G
1
B E
C
D
6
1
64
3
1
4
3
F
E
A
A
A
ECN:
M/N:
BIOS:
B
B
B
Made in Taiwan
17-143-094202
S/N:
E
C
C
F
SIO
BM-0947 Rear Component locations

Chapter 2 Hardware Configuration
BM-0947 USER ′ S MANUAL Page: 2-5
2-3. HOW TO SET JUMPERS
You can configure your board by setting jumpers. Jumper is consists of two or three metal
pins with a plastic base mounted on the card, and by using a small plastic "cap", Also
known as the jumper cap (with a metal contact inside), you are able to connect the pins.
So you can set-up your hardware configuration by "open"or "close"pins.
The jumper can be combined into sets that called jumper blocks. When the jumpers are all
in the block, you have to put them together to set up the hardware configuration. The figure
below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3), You can connect
PIN1 & PIN2 to create one setting by shorting. You can either connect PIN2 & PIN3 to
create another setting. The same jumper diagrams are applied all through this manual. The
figure below shows what the manual diagrams look and what they represent.

Chapter 2 Hardware Configuration
BM-0947 USER ′ S MANUAL Page: 2-6
Jumper Diagrams
2 pin Jumper
looks like this
Jumper Cap
looks like this
3 pin Jumper
looks like this
Jumper Block
looks like this
Jumper Settings
Looks like this
3 pin Jumper
2-3 pin close(enabled)
Looks like this
Jumper Block
1-2 pin close(enabled)
2 pin Jumper close(enabled)
1
1
1
2
1 2
1
1
Looks like this

Chapter 2 Hardware Configuration
BM-0947 USER ′ S MANUAL Page: 2-7
2-4. COM PORT
COM1, COM5: COM Port, fixed as RS-232
PIN
ASSIGNMENT PIN
ASSIGNMENT
1 DCD# 6 DSR#
2 RX 7 RTS#
3 TX 8 CTS#
4 DTR# 9 RI#
5 GND
COM2: COM2 Connector, selectable as RS-232/422/485
Co-lay with the other COM port stacked over COM1.
ASSIGNMENT
PIN
RS-232 RS-422 RS-485
1 DCD# TX- RS-485-
2 RX TX+ RS-485+
3 TX RX+ X
4 DTR# RX- X
5 GND GND GND
6 DSR# X X
7 RTS# X X
8 CTS# X X
9 RI# X X
5
1
9
6
COM1/
COM5
/
5
1
9
6
COM2

Chapter 2 Hardware Configuration
BM-0947 USER ′ S MANUAL Page: 2-8
2-5. COM CONNECTOR
COM3, COM4, COM6: COM3 & COM4 Connectors, fixed as RS-232
PIN
ASSIGNMENT PIN
ASSIGNMENT
1 DCD# 6 DSR#
2 RX 7 RTS#
3 TX 8 CTS#
4 DTR# 9 RI#
5 GND 10 NC
2-6. VGA PORT
VGA1: VGA Port
PIN
ASSIGNMENT PIN
ASSIGNMENT
1 RED 9 VCC5
2 GREEN1 10 GND
3 BLUE 11 NC
4 NC 12 DDC_DATA
5 GND 13 HSYNC
6 GND 14 VSYNC
7 GND 15 DDC_CLK
8 GND
1
6
5
10
COM3/
COM4/
COM6/
15 610 1115
VGA1

Chapter 2 Hardware Configuration
BM-0947 USER ′ S MANUAL Page: 2-9
2-7. KEYBOARD & MOUSE PORT
KB_MS1: PS/2 Keyboard & Mouse Port
Keyboard:
PIN
ASSIGNMENT PIN
ASSIGNMENT
1 KBDATA 4 VCC5
2 NC 5 KBCLK
3 GND 6 NC
Mouse:
PIN
ASSIGNMENT PIN
ASSIGNMENT
7 MSDATA 10 VCC5
8 NC 11 MSCLK
9 GND 12 NC
3
12
4
56
9
78
10
1112
MS
KB
KB_MS1

Chapter 2 Hardware Configuration
BM-0947 USER ′ S MANUAL Page: 2-10
2-8. LAN & USB3.0 PORT
LAN1_USB1: LAN & Two USB3.0 Ports
LAN1 signal:
PIN
ASSIGNMENT PIN
ASSIGNMENT
1 MDI_0P 5 MDI_2N
2 MDI_0N 6 MDI_1N
3 MDI_1P 7 MDI_3P
4 MDI_2P 8 MDI_3N
LAN LED Indicator:
Left Side LED
Green Color On 10/100 LAN Speed Indicator
Orange Color On
Giga LAN Speed Indicator
Off No LAN switch/hub connected.
Right Side LED
Yellow Color Blinking LAN Message Active
Off No LAN Message Active
USB3.0 signal:
PIN
ASSIGNMENT PIN
ASSIGNMENT
A1 VCC5 B1 VCC5
A2 USBP0N B2 USBP1N
A3 USBP0P B3 USBP1P
A4 GND B4 GND
A5 RX1_DN B5 RX2_DN
A6 RX1_DP B6 RX2_DP
A7 GND B7 GND
A8 TX1_DN B8 TX2_DN
A9 TX1_DP B9 TX2_DP
Green/Orange Yellow
B1 B4
B9 B5
A1 A4
A9 A5
8 1
LAN1_USB1