Proto-X 4606 User manual
FCC STATEMENT AND INDUSTRY CANADA NOTICE:
1. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Remark: This device is in accordance with the digital device grade B limitation and the
15th regulation of FCC. This limitation requires reasonable anti-interference protection
around the residence. The device can transmit radio wave during use and can interrupt
the mobile communication without proper installment. Interruption will occur for special
device. If the device do interrupt the radio or television, please turn the device off then turn
it on to adjust. Below are some resolution for your reference:
•Move the receiving antenna
•Enlarge the distance between the device and receiver
•Try to not connect the device and the receiver on the same circuit
•Ask for professional help from experts
3. This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of Industry Canada.
• Do not turn on quadcopter unless controller has been turned on first.
• Keep hands, hair and loose clothing away from spinning blades.
• Turn off controller and quadcopter when not in use.
• Parental guidance is recommended.
• Do not submerge into water. This could damage electronic assemblies.
• Follow operating instructions exactly.
• Not intended for children under 8 years old.
• Replace any damaged or broken parts before attempting to fly.
• Do not drop the quadcopter by suddenly reducing the throttle. This
could lead to severe damage.
•
The quadcopter’s range will also be affected if the battery is not fully charged.
• Do not touch the motors after flying. They can become hot.
• The battery in the quadcopter is not replaceable.
CAUTION: Changes or modifications to
this product not expressly approved by
the party responsible for compliance may
void the user’s authority to operate the
equipment.
90 DAY LIMITED WARRANTY
PLEASE DO NOT RETURN YOUR PRODUCT TO THE STORE – Proto-X will repair or replace factory defects for 90 days from the date of purchase. This
warranty specifically does not cover crash damage, misuse or abuse. To make a warranty claim, please contact our product support team at 1-217-398-
If requested by Product Support, please send defective product to: Hobby Services, 3002 N Apollo Dr., Suite #1, Champaign, IL 61822
This warranty applies only if the product is operated in compliance with the instructions and warnings provided with each model. Proto-X assumes no liability except
for the exclusive remedy or repair of parts as specified above. Proto-X shall not be liable for consequential or incidental damages. Some states do not allow the
exclusion of consequential or incidental damages so the above exclusion may not apply to you. This warranty gives you specific legal rights and you may also have
other rights which vary from state to state.
Battery Requirements for Controller:
Requires: 2 x 1.5V AAA size batteries (not included)
Requirements for USB Charge Cord:
USB Output Jack (not included)
Battery Cautions:
• Parental guidance is recommended when installing batteries.
• Do not power controller by mixing different types of batteries, or old and new batteries.
• Use only batteries of the same or equivalent type as those recommended.
The quadcopter is equipped with a rechargeable 3.7V LiPo battery.
Please pay attention to the following cautions for safe use:
• Do not dispose of battery into fire or heat.
• Do not use or leave battery near a heat source, such as fire or a heater.
• Do not strike battery or throw it against a hard surface.
• Do not pierce battery.
• Do not disassemble or alter battery.
• Turn off power switch after use.
• Recycle used batteries.
Do not touch the
spinning blades or
fly over another person’s
head. Adult supervision is
required.
ON OFF
12
3 4 5
GET READY TO FLY
Plug the charger into a USB port and
quadcopter as shown. (The battery
connector will only fit in one way. Do
not force the connectors together.)
The red LED will light when charging.
The red LED will shut off once the
charge is complete.
The Proto-X must be powered
off before charging.
Set the quadcopter on a level surface until
the blue LEDs change from blinking to
solid.
Switch on controller. Make
sure left stick is down.
LED
Off
On
NEVER leave the quadcopter unattended
when charging.
DO NOT allow the USB port to power down
when connected to the quadcopter.
ALWAYS unplug the quadcopter when
charging is complete.
4606
Proto-X c/o Hobbico, Inc.
2904 Research Road Champaign, IL USA 61826
Made In Dongguan, Guangdong, China
Contents
HOW TO FLY
CORRECTING DRIFT
LANDING SAFELY
TROUBLESHOOTING
REPLACEMENT BLADES
It is normal for the quadcopter to drift slightly. However if it drifts
in any direction consistently press the trim button opposite the
movement as many times a needed to eliminate the drift.
UP FORWARD
FORWARD
DOWN
ROTATE LEFT
ROTATE LEFT LEFT
LEFT
LEFT TRIM
FORWARD TRIM
FORWARD TRIM
LEFT TRIM
ROTATE RIGHT
ROTATE RIGHT RIGHT
RIGHT
RIGHT TRIM
FRONT
Gray Blades, Blue LEDs
REAR
Black Blades, Red LEDs
BACKWARD TRIM
BACKWARD TRIM
RIGHT TRIM
BACKWARD
BACKWARD
DOWN
UP
When the battery voltage begins to run low, the LEDs will begin
to flash. It is time to land before the built in low voltage cut off
reduces power to the motors.
PROBLEM: Controller cannot be linked to the quadcopter.
SOLUTION: Throttle position needs to be at zero.
PROBLEM: Controller LED flashing after binding.
SOLUTION: Replace batteries.
PROBLEM: Quadcopter shaking.
SOLUTION: Check if the canopy, chassis and rotors are damaged.
PROBLEM: Will not take off.
SOLUTION: Check that the rotor blades are properly installed.
CALIBRATING THE SENSORS
If the quadcopter doesn’t trim well,
recalibrate the sensors.
1. Turn on the controller and the quadcopter. Place the quadcopter on a
flat surface.
2. Hold the left stick to the lower right. At the same time, quickly move the
right stick left and right several times until the blue LED’s flash.
4606 © 2014 Proto-X, a Hobbico company.
protoquad.com
