Psion OMNII User manual

Version with Scanner
Version with pistol grip
Version without Scanner
OPEN
LOCK
OPEN
LOCK
Contents of the Box
features
front, right and Left
Omnii This Guide Additional Documentation
(dependent on order)
LEDs Speaker
Volume
Rocker Button
Scan Button
Microphone
Beeper
Battery Release Button
Vertical
Scroll
Button
ENTER
Button
expansion BaCk Cover
Battery Compartment getting started
features and variants
miCrosd and sim Card sLots
Camera
PTT Speaker
Blanking Plate
Standard Back Cover
Expansion Back Cover with
Scanner/Imager Pod
standard BaCk Cover
Note: For all variants of both back covers, a pistol grip is available.
Note: GPS radio and end-cap, PTT speaker, and camera are all options
available with the Expansion Back Cover.
Standard Back Covers can support a variety of scanners and imagers.
To insert a microSD or SIM card:
>Press the battery release buttons to remove the battery.
>Use a Phillips screwdriver to remove the SD cover screw.
>Flip the cover open.
microSD card
>Slide the microSD door to the left to
unlock it. Flip it open.
>Slide the microSD card onto the
guides on the SD card door.
>Close the microSD door, and slide it
to the right to lock it.
SIM card
>Slide the SIM card metal door latch
to the right to unlock it. Flip it open.
>Slide the SIM card into the guides on
the SIM card door.
>Close the SIM card door, and slide the
metal door latch to the left to lock it.
SIM Card Slot
microSD
Card Slot
SD Cover
Insert the Battery
Snap the Battery into Place
Press down firmly on both sides of the battery to ensure that it
is securely seated in Omnii.
1
2
over >

April 7, 2011
PN 8000223.A
ISO 9001 Certified
Quality Management System
QuiCk start
guide
resetting the unit
To perform a cold reset:
>Press the SYM key, the FN key, and the ENTER/Power key
simultaneously for six seconds.
During a cold reset, running programs are halted and RAM memory is
cleared. The contents of flash memory and the registry are preserved.
The operating system is reloaded.
To perform a warm reset:
>Press the FN key and the ENTER/Power key simultaneously
for a few seconds.
During a warm reset, running programs are halted. The contents of
RAM, flash memory, and the registry are preserved.
Turn the Unit On
Press and hold down the ENTER/
Power key for at least one second.
Charge the Battery
The power adaptor can be
plugged into a snap module
attached to Omnii.
The power adaptor can also
be plugged into the desktop
docking station.
Allow the battery to charge for 3-4 hours.
Note: Use only the universal AC
power adaptor and
IEC320-C13 power cord
approved by Psion for
Omnii.
Note: Full battery performance is only reached after the first
few full charge/discharge cycles.
ENTER/Power Key
Snap Module
Connect Omnii to the PC
Connect through a docking station or a snap module
with a USB port.
Install and Configure Data Transfer Software
Use ActiveSync®(Windows®XP®or earlier) or Mobile Device Cen-
ter® (Windows Vista®or Windows 7®) to establish a connection
between Omnii and the PC and synchronize your e-mail, contacts,
and so on.
For either ActiveSync or Mobile Device Center, go to the following
website:
http://go.microsoft.com/fwlink/?LinkId=147001
To Turn Omnii Off, Do One of the Following:
>Press the FN key followed by the ENTER/Power key, or
>In the Start menu, choose Shutdown>Suspend.
43
5
6
7
0 – 40˚ C
32 – 104˚ F
hand-heLd
Computer
Important: Resetting may result in data loss.
© Copyright 2011 by Psion Inc.
Psion, Psion Teklogix, and Omnii are trademarks of Psion Inc. Other product names
mentioned in this document are trademarks or registered trademarks of other hardware,
software, or service providers and are used herein for identification purposes only.