PT W53991 User manual

WARNING
It is the owner and/or operators’ responsibility to study all WARNINGS, operating, and maintenance
instructions contained on the product label and instruction manual prior to operating this tool. The
owner/operator shall retain product instructions for future reference.
The owner and/or operator are responsible for maintenance, maintaining all decals or warning
labels and while in use, maintaining the unit in good working order. If the owner and/or operator
are not fluent in English, the product warnings and instructions shall be read and discussed with
the operators’ native language by the purchaser/owner or his designee. Make sure that the
operator comprehends its contents. Safety information shall be emphasized and understood
prior to usage.
Protect yourself and others by observing all safety information.
Failure to comply with instructions could result in personal injury and/or property damage!
If you encounter any problems or difficulties, please contact our customer service department
at: 1-800-426-1262 between 6:30 a.m. and 4:30 p.m. Pacific time.
INDUSTRIAL UTILITY CART
OWNERS MANUAL
Stock Number W53991
Please read these instructions carefully and retain them for future use.

Note: Use a rubber mallet to ensure snug connection of all nonmetal parts.
1. Place the bases of the four Posts (2,3) into the corners of the Tray (1).
 TheFlangeoneachPostwillonlytintocertaincorners.
2. Insert Carriage Bolt (10) down through the holes in the bases of the Posts (2,3).
3. Attach Casters (6,7) to Carriage Bolts (10) using Split Washers (11) and Nuts (12). For best
operation, the two Straight Casters (6) go on the same end of the cart, and the two Swivel
Casters (7) go on the other end.
4. Place the other Tray (1) upside down on the work surface. Turn the Handle (8) upside down with
the cup holder toward the Tray and the hand holes on the outside.
5.PlacetheTraywithttheHandlermlyontopofthePosts(2,3).PositiontheHandleaboveeither
 theswivelofxedcasters,dependingonoperationpreference.
6. Place a Post Cap (4,5) on top of each corner of the Tray (1).
7. Use three Screws (9) through each Post (2,3) from underneath to secure them.
ASSEMBLY INSTRUCTIONS
SPECIFICATIONS
Industrial Utility Cart: ..........................................................W53991
Construction:............................................High Impact Poly-Propylene
Maximum Capacity:.................................................................500 Lbs.
Tray Size: ................................................. 30 in. L x 16 in. W x 3 in. D
Overall dimensions: ...................39-3/4 in. L x 17 in. W x 33-1/4 in. H
IMPORTANT SAFETY INFORMATION
Specifications are
subject fo change
without notice
Read these safety warnings before operation.
Assemble only according to these instructions. Improper assembly can create hazards.
Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
Keep assembly area clean and well lit.
Keep bystanders out of the area during assembly.
Do not assemble when tired or when under the influence of drugs or medication.
Weight capacity and other product capabilities apply to properly and completely
assembled product only.
This product is not a toy. Do not allow children to play with or near this item.
Use as intended only.
Inspectbeforeeveryuse:donotuseifpartsarelooseordamaged.Donotexceedlisted
weight capacity, evenly distributed. Be aware of dynamic loading! Sudden load
movementmaybrieflycreateexcessloadcausingproductfailure.
Use only on flat, level, hard surface able to properly support cart and load.
Maintain product labels and nameplates. These carry important safety information.

Part Description Qty.
1 Tray 2
2 RH Post 2
3 LH Post 2
4 RH Post Cap 2
5 LH Post Cap 2
6 Straight Caster 2
Part Description Qty.
7 Swivel Caster 2
8 Handle 1
9 Screw 12
10 Carriage Bolt 16
11 Split Washer 16
12 Nut 16
PARTS LISTING
PARTS DIAGRAM
1
2
3
4
5
6
7
8
9
10
11
12

1 YEAR LIMITED WARRANTY
PERFORMANCE TOOL® extends only the following warranties, and only to original retail purchasers. These
warranties give specific legal rights. Except where prohibited by local law, the law of the State of Washington
governs all warranties and all exclusions and limitations of warranties and remedies. There may be other rights
which vary from state to state.
PERFORMANCE TOOL® warrants the product to be free from defects in materials and workmanship under
normal use and service. A defective product may be returned for a free replacement within 90 days from the
date of purchase, provided that product is returned to place of purchase immediately after discovery of defect.
After 90 days and up to one year from date of purchase, PERFORMANCE TOOL® will replace at no charge any
parts which our examination shall disclose to be defective and under warranty. These warranties shall be valid
only when a sales receipt showing the date of purchase accompanies the defective product or defective part (s)
being returned. For part (s) after 90 days, please remit your request, postage prepaid to:
PERFORMANCE TOOL, P.O. Box 88259 Tukwila, WA 98138
These warranties exclude blades, bits, punches, dies, bulbs, fuses, hoses, and other consumables which must
be replaced under normal use and service. These warranties shall not apply to any product or part which is
used for a purpose for which it is not designed, or which has been repaired or altered in any way so as to affect
adversely its performance or reliability, nor shall these warranties apply to any product or part which has been
subject to misuse, neglect, accident or wear and tear incident to normal use and service.
PERFORMANCE TOOL® does not authorize any other person to make any warranty or to assume any liability in
connection with its products.
Except for warranties of title and the limited express warranties set forth above, PERFORMANCE TOOL®
makes no express or implied warranties of any kind with respect to its products. In particular, PERFORMANCE
TOOL® makes no implied warranty of merchantability and no implied warranty of fitness for any particular
purpose, except that for goods purchased primarily for personal, family or household use and not for
commercial or business use, PERFORMANCE TOOL® makes an implied warranty of merchantability (and, if
otherwise applicable, an implied warranty of fitness for a particular purpose), but only for the particular qualities
or characteristics, and for the duration, expressly warranted above.
The laws on limitation of implied warranties may differ from state to state, so the above limitations may not
apply in all cases.
PERFORMANCE TOOL® shall not be liable for consequential, incidental or special damages resulting from or in
any manner related to any product, or to the design, use, or any inability to use the product. The sole and
exclusive remedy for a defective product or part shall be the repair, or replacement thereof as provided above.
The laws on limitation of remedies or on consequential, incidental or special damages may vary from state to
state, so the above limitations may not apply in all cases.
© Copyright 2015 WILMAR CORPORATION, P.O. Box 88259 Tukwila, WA 98138
On occasion, after printing of our literature is completed, our manufacturers may make changes and/or modifications to
merchandise which will not be reflected in this manual. Although we strive to maintain complete and accurate information, it is
possible in some instances, that the product may differ slightly from printed specifications. Illustrations are intended for
reference only. Actual merchandise may vary. Wilmar is not responsible for typographical errors.